Abstract:This paper presents the first experimental engine and test rig results obtained from a fast response cooled total pressure probe. The first objective of the probe design was to favor continuous immersion of the probe into the engine to obtain a time series of pressure with a high bandwidth and, therefore, statistically representative average fluctuations at the blade passing frequency. The probe is water cooled by a high pressure cooling system and uses a conventional piezoresistive pressure sensor, which yields, therefore, both time-averaged and time-resolved pressures. The initial design target was to gain the capability of performing measurements at the temperature conditions typically found at high pressure turbine exit (800–1100°C) with a bandwidth of at least 40 kHz and in the long term at combustor exit (2000 K or higher). The probe was first traversed at the turbine exit of a Rolls-Royce Viper turbojet engine at exhaust temperatures around 750°C and absolute pressure of 2.1 bars. The probe was able to resolve the high blade passing frequency (≈23 kHz) and several harmonics of up to 100 kHz. Besides the average total pressure distributions rom the radial traverses, phase-locked averages and random unsteadiness are presented. The probe was also used in a virtual three-hole mode yielding unsteady yaw angle, static pressure, and Mach number. The same probe was used for measurements in a Rolls-Royce intermediate pressure burner rig. Traverses were performed inside the flame tube of a kerosene burner at temperatures above 1600°C. The probe successfully measured the total pressure distribution in the flame tube and typical frequencies of combustion instabilities were identified during rumble conditions. The cooling performance of the probe is compared with estimations at the design stage and found to be in good agreement. The frequency response of the probe is compared with cold shock-tube results and a significant increase in the natural frequency of the line-cavity system formed by the conduction cooled screen in front of the miniature pressure sensor were observed.

Evaluation and Validation of PSP and TSP Measurement Techniques in Turbomachinery Applications

A TEMPERATURE-GRADIENT CORRECTION METHOD FOR FILM COOLING EFFECTIVENESS MEASUREMENT USING ENDOSCOPE-BASED PSP TECHNIQUE

Improved Apparatus for Inline Measurement of Residence Time Distribution of Thermomechanically Complex Systems

An Experimental Study of Turbine Vane Film Cooling Using Endoscope-Based PSP Technique in a Single-Passage Wind Tunnel

Temperature- and Pressure-Sensitive Paint Measurements in Short-Duration Hypersonic Flow

Quantification Of Performance Uncertainty For A Transonic Compressor Rotor Using An Adaptive Nipc Method

Pressure-sensitive paint measurements in a shock tube

A method of in-situ monitoring multiple parameters and blade condition of turbomachinery by using a single acoustic pressure sensor

Experimental analysis of pressure deviation-induced film cooling effectiveness deviation in pressure sensitive paint measurement

Fast pressure-sensitive paint measurements of dynamic stall on a pitching airfoil via intensity- and lifetime-based methods

Resolving dynamic features of kilohertz pressure fluctuations using fast-responding pressure-sensitive paint: measurement of inclined jet impingement

High-temperature high-frequency turbine exit flow field measurements in a military engine with a cooled unsteady total pressure probe

Unsteady Pressure Measurements With a Fast Response Cooled Probe in High Temperature Gas Turbine Environments

Time-resolved pressure-sensitive paint measurements for cryogenic wind tunnel tests

Experimental Study of Shaped Hole Film Cooling Using Pressure Sensitive Paint

Unsteady Pressure-Sensitive-paint (PSP) Measurement in Low-Speed Flow: Characteristic Mode Decomposition and Noise Floor Analysis

An Ultra-Fast TSP on a CNT Heating Layer for Unsteady Temperature and Heat Flux Measurements in Subsonic Flows

Investigation of Flow Structure in a Turbocharger Turbine under Pulsating Flow Conditions

Pressure-Sensitive Paint Measurements in Narrow Clearances: A Feasibility Study

Initial Study of the Onsite Measurement of Flow Sensors on Turbine Blades (SOTB)

Characterization of the Endwall Flow in a Low-Pressure Turbine Cascade Perturbed by Periodically Incoming Wakes, Part 2: Unsteady Blade Surface Measurements Using Pressure-Sensitive Paint