Carrier engineering of Zr-doped Ta3N5 film as an efficient photoanode for solar water splitting

Xin Zou,Xueyang Han,Chengxiong Wang,Yunkun Zhao,Chun Du,Bin Shan

DOI: https://doi.org/10.1039/d1se00640a

2021-01-01

Abstract:Ta3N5 is regarded as a promising candidate material with adequate visible light absorption and band structure for photoelectrochemical water splitting.

What problem does this paper attempt to address?

Carrier Engineering of Zr-doped Ta3N5 Film As an Efficient Photoanode for Solar Water Splitting

Xin Zou,Xueyang Han,Chengxiong Wang,Yunkun Zhao,Chun Du,Bin Shan

DOI: https://doi.org/10.1039/d1se00640a

IF: 6.813

2021-01-01

Sustainable Energy & Fuels

Abstract:Ta3N5 is regarded as a promising candidate material with adequate visible light absorption and band structure for photoelectrochemical water splitting.
Interface Engineering of Ta3N5 Thin Film Photoanode for Highly Efficient Photoelectrochemical Water Splitting

Jie Fu,Zeyu Fan,Mamiko Nakabayashi,Huanxin Ju,Nadiia Pastukhova,Yequan Xiao,Chao Feng,Naoya Shibata,Kazunari Domen,Yanbo Li

DOI: https://doi.org/10.1038/s41467-022-28415-4

IF: 16.6

2022-01-01

Nature Communications

Abstract:Interface engineering is a proven strategy to improve the efficiency of thin film semiconductor based solar energy conversion devices. Ta 3 N 5 thin film photoanode is a promising candidate for photoelectrochemical (PEC) water splitting. Yet, a concerted effort to engineer both the bottom and top interfaces of Ta 3 N 5 thin film photoanode is still lacking. Here, we employ n-type In:GaN and p-type Mg:GaN to modify the bottom and top interfaces of Ta 3 N 5 thin film photoanode, respectively. The obtained In:GaN/Ta 3 N 5 /Mg:GaN heterojunction photoanode shows enhanced bulk carrier separation capability and better injection efficiency at photoanode/electrolyte interface, which lead to a record-high applied bias photon-to-current efficiency of 3.46% for Ta 3 N 5 -based photoanode. Furthermore, the roles of the In:GaN and Mg:GaN layers are distinguished through mechanistic studies. While the In:GaN layer contributes mainly to the enhanced bulk charge separation efficiency, the Mg:GaN layer improves the surface charge inject efficiency. This work demonstrates the crucial role of proper interface engineering for thin film-based photoanode in achieving efficient PEC water splitting.
Engineering band structure via dual atoms modification for the efficient photoanode

Yu Wang,Xiao-dong Wang,Chuanzhen Feng,Huijuan Zhang

DOI: https://doi.org/10.1039/d3sc05420a

IF: 8.4

2023-11-08

Chemical Science

Abstract:Efficient carrier separation is important for improving photochemical water splitting. Here, the morphology modification and band structure engineering of Ta3N5 are accomplished by doping Cu and Zr using a two-step method for the first time. The initially interstitial doped Cu atoms can act as anchors to interact with subsequently doped Zr atoms under the influence of electronegativity differences. This interaction results in Cu,Zrg-Ta3N5 having a dense morphology and higher crystallinity, which helps to reduce carrier recombination at grain boundaries. Furthermore, the gradient doping of Zr causes a band edge energy gradient, which significantly enhance bulk charge separation efficiency. Therefore, a photoanode based on the Cu,Zrg-Ta3N5 delivers an onset potential of 0.38 VRHE and a photocurrent density of 8.9 mA cm-2 at 1.23 VRHE. Compared to all the Ta3N5-based photoanodes deposited on FTO, Cu,Zrg-Ta3N5 based photoanode has the lowest onset potential and highest photocurrent. The novel material morphology regulation and band edge position engineering strategies provide new ideas for the preparation of other semiconductor nanoparticles to improve the PEC water splitting performance.

chemistry, multidisciplinary
Ge-mediated modification in Ta3N5 photoelectrodes with enhanced charge transport for solar water splitting.

Jianyong Feng,Dapeng Cao,Zhiqiang Wang,Wenjun Luo,Jiajia Wang,Zhaosheng Li,Zhigang Zou

DOI: https://doi.org/10.1002/chem.201402760

2014-01-01

Chemistry - A European Journal

Abstract:Ta3N5 is a promising photoanode candidate for photoelectrochemical water splitting, with a band gap of about 2.1eV and a theoretical solar-to-hydrogen efficiency as high as 15.9% under AM 1.5G 100mWcm(-2) irradiation. However, the presently achieved highest photocurrent (ca. 7.5mAcm(-2)) on Ta3N5 photoelectrodes under AM 1.5G 100mWcm(-2) is far from the theoretical maximum (ca. 12.9mAcm(-2)), which is possibly due to serious bulk recombination (poor bulk charge transport and charge separation) in Ta3N5 photoelectrodes. In this study, we show that volatilization of intentionally added Ge (5%) during the synthesis of Ta3N5 promotes the electron transport and thereby improves the charge-separation efficiency in bulk Ta3N5 photoanode, which affords a 320% increase of the highest photocurrent comparing with that of pure Ta3N5 photoanode under AM 1.5G 100mWcm(-2) simulated sunlight.
Decoupling light absorption and carrier transport via heterogeneous doping in Ta3N5 thin film photoanode

Yequan Xiao,Zeyu Fan,Mamiko Nakabayashi,Qiaoqiao Li,Liujiang Zhou,Qian Wang,Changli Li,Naoya Shibata,Kazunari Domen,Yanbo Li

DOI: https://doi.org/10.1038/s41467-022-35538-1

IF: 17.694

2022-12-16

NanoScience and Technology

Abstract:The trade-off between light absorption and carrier transport in semiconductor thin film photoelectrodes is a major limiting factor of their solar-to-hydrogen efficiency for photoelectrochemical water splitting. Herein, we develop a heterogeneous doping strategy that combines surface doping with bulk gradient doping to decouple light absorption and carrier transport in a thin film photoelectrode. Taking La and Mg doped Ta 3 N 5 thin film photoanode as an example, enhanced light absorption is achieved by surface La doping through alleviating anisotropic optical absorption, while efficient carrier transport in the bulk is maintained by the gradient band structure induced by gradient Mg doping. Moreover, the homojunction formed between the La-doped layer and the gradient Mg-doped layer further promotes charge separation. As a result, the heterogeneously doped photoanode yields a half-cell solar-to-hydrogen conversion efficiency of 4.07%, which establishes Ta 3 N 5 as a leading performer among visible‐light‐responsive photoanodes. The heterogeneous doping strategy could be extended to other semiconductor thin film light absorbers to break performance trade-offs by decoupling light absorption and carrier transport.
Enhanced Water‐Splitting Performance of Perovskite SrTaO2N Photoanode Film Through Ameliorating Interparticle Charge Transport

Yujiao Zhong,Zhaosheng Li,Xin Zhao,Tao Fang,Huiting Huang,Qinfeng Qian,Xiaofeng Chang,Peng Wang,Shicheng Yan,Zhentao Yu,Zhigang Zou

DOI: https://doi.org/10.1002/adfm.201603021

IF: 19

2016-01-01

Advanced Functional Materials

Abstract:Here SrTaO2N has been found to exhibit photoelectrochemical water splitting, with a theoretical solar‐to‐hydrogen efficiency of 14.4%. Ameliorating the interparticle charge transport by H2 annealing, the solar photocurrent of the SrTaO2N(H) granular film at 1.23 V versus reversible hydrogen electrode (RHE) is increased by ≈250% in comparison with the SrTaO2N film. Using an aberration corrected scanning transmission electron microscope and super‐X energy dispersive spectroscopy, the atomic scale observation has proved a decrease of oxygen concentrations in the surface of SrTaO2N(H) particle, which may allow its electrical conductivity to be increased from 0.77 × 10−6 to 2.65 × 10−6 S cm−1 and therefore the charge separation efficiency has been greatly increased by ≈330%. After being modified by Co–Pi water oxidation catalyst, the SrTaO2N(H) photoanode shows a solar photocurrent of 1.1 mA cm−2 and an incident photo‐to‐current efficiency value of ≈20% at 400–460 nm and 1.23 V versus RHE, which suggests that it is a new promising photoanode material for solar water splitting.
Band structure engineering and defect control of Ta3N5 for efficient photoelectrochemical water oxidation

Yequan Xiao,Chao Feng,Jie Fu,Faze Wang,Changli Li,Viktoria F. Kunzelmann,Chang-Ming Jiang,Mamiko Nakabayashi,Naoya Shibata,Ian D. Sharp,Kazunari Domen,Yanbo Li

DOI: https://doi.org/10.1038/s41929-020-00522-9

IF: 37.8

2020-10-12

Nature Catalysis

Abstract:Ta3N5 is a promising photoanode material with a theoretical maximum solar conversion efficiency of 15.9% for photoelectrochemical water splitting. However, the highest applied bias photon-to-current efficiency achieved so far is only 2.72%. To bridge the efficiency gap, effective carrier management strategies for Ta3N5 photoanodes should be developed. Here, we propose to use gradient Mg doping for band structure engineering and defect control of Ta3N5. The gradient Mg doping profile in Ta3N5 induces a gradient of the band edge energetics, which greatly enhances the charge separation efficiency. Furthermore, defect-related recombination is significantly suppressed due to the passivation effect of Mg dopants on deep-level defects and, more importantly, the matching of the gradient Mg doping profile with the distribution of defects within Ta3N5. As a result, a photoanode based on the gradient Mg-doped Ta3N5 delivers a low onset potential of 0.4 V versus that of a reversible hydrogen electrode and a high applied bias photon-to-current efficiency of 3.25 ± 0.05%.

chemistry, physical
LaCl3 Flux Mediated Ta3N5 Planar Photoanode for Solar Water Oxidation

Zirui Lou,Yingchen Yang,Yichen Wang,Chao Qin,Rong Liang,Yanwen Wang,Zhizhen Ye,Liping Zhu

DOI: https://doi.org/10.1016/j.cej.2020.125161

IF: 15.1

2020-01-01

Chemical Engineering Journal

Abstract:Ta3N5 is a promising candidate for photoelectrochemical (PEC) water splitting. Recently gratifying photo-currents have been reported through various advanced techniques. However, obtaining high performance Ta3N5 photoanode prepared by direct oxidation and nitridation remains challenging. In this work, efficient Ta3N5 photoanode was fabricated on Ta foil by direct oxidation and nitridation method with LaCl3 flux mediated treatment. The highest photoresponse (8.2 mA cm(-2) @ 1.23 VRHE) for direct oxidized and nitrided Ta3N5 is achieved with the help of LaCl3 flux, which is nearly doubled compared to the untreated counterparts. Theoretical analysis suggests an interfacial charge transfer in LaTaON2/Ta3N5 heterostructure and significant increase in carrier concentration on La doped Ta3N5 surface. The introduction of LaCl3 flux brings a new look to this traditional method and it may potentially be applied to large area and low cost photoanodes.
A co-catalyst-loaded Ta(3)N(5) photoanode with a high solar photocurrent for water splitting upon facile removal of the surface layer.

Mingxue Li,Wenjun Luo,Dapeng Cao,Xin Zhao,Zhaosheng Li,Tao Yu,Zhigang Zou

DOI: https://doi.org/10.1002/anie.201305350

2013-01-01

Abstract:Surface exfoliation: A Ta3 N5 photoanode prepared by a thermal oxidation and nitridation method shows a high solar photocurrent. This photocurrent is currently the highest achieved by a Ta3 N5 photoanode. The photocurrent is obtained mainly because of facile thermal and mechanical exfoliation of the surface passivation layer of the Ta3 N5 photoanode.
Surface Chemistry and Photoelectrochemistry-Case Study on Tantalum Nitride.

Yumin He,Rong Chen,Wenjun Fa,Bingqing Zhang,Dunwei Wang

DOI: https://doi.org/10.1063/1.5122996

IF: 4.304

2019-01-01

The Journal of Chemical Physics

Abstract:Solar water splitting promises a solution to challenges associated with the intermittent nature of solar energy. Of different implementations, photoelectrochemical water splitting, where one or more photoelectrodes harvest light and catalyze water splitting, represents a convenient platform to understand the governing principles of charge behaviors, especially at the light absorber|H2O interface. This Perspective recognizes and discusses the importance of the photoelectrode surface to solar water splitting performance. It presents discussions within the context of a prototypical water splitting material, Ta3N5, which has gained growing attention lately for its outstanding initial performance. Insights into the mechanisms by which Ta3N5 functions are presented, followed by examples of recent efforts to circumvent the issues that Ta3N5 decays rapidly under solar water splitting conditions. Our visions on the future directions of semiconductor-based solar water splitting will be presented at the end.
A Co-catalyst-Loaded Ta3N5Photoanode with a High Solar Photocurrent for Water Splitting upon Facile Removal of the Surface Layer

Mingxue Li,Wenjun Luo,Dapeng Cao,Xin Zhao,Zhaosheng Li,Tao Yu,Zhigang Zou

DOI: https://doi.org/10.1002/anie.201305350

2013-01-01

Angewandte Chemie

Abstract:Surface exfoliation: A Ta3 N5 photoanode prepared by a thermal oxidation and nitridation method shows a high solar photocurrent. This photocurrent is currently the highest achieved by a Ta3 N5 photoanode. The photocurrent is obtained mainly because of facile thermal and mechanical exfoliation of the surface passivation layer of the Ta3 N5 photoanode.
What Limits the Performance of Ta3N5 for Solar Water Splitting

Yumin He,James E. Thorne,Cheng Hao Wu,Peiyan Ma,Chun Du,Qi Dong,Jinghua Guo,Dunwei Wang

DOI: https://doi.org/10.1016/j.chempr.2016.09.006

IF: 23.5

2016-01-01

Chem

Abstract:Tantalum nitride (Ta3N5) is a promising photoelectrode for solar water splitting. Although near-theoretical-limit photocurrent has already been reported on Ta3N5, its low photovoltage and poor stability remain critical challenges. In this study, we used Ta3N5 nanotubes as a platform to understand the origins of these issues. Through a combination of photoelectrochemical and high-resolution electron microscope measurements, we found that the self-limiting surface oxidation of Ta3N5 resulted in a thin amorphous layer (ca. 3 nm), which proved to be effective in pinning the surface Fermi levels and thus fully suppressed the photoactivity of Ta3N5. X-ray core-level spectroscopy characterization not only confirmed the surface composition change resulting from the oxidation but also revealed a Fermi-level shift toward the positive direction by up to 0.5 V. The photoactivity degradation mechanism reported here is likely to find applications in other solar-to-chemical energy-conversion systems.
Charge Carrier Transfer in Ta3n5 Photoanodes Prepared by Different Methods for Solar Water Splitting

Mingxue Li,Wenjun Luo,Liheng Yang,Xin Zhao,Zhigang Zou

DOI: https://doi.org/10.1071/ch15466

2016-01-01

Australian Journal of Chemistry

Abstract:The preparation method of a photoanode can affect its water splitting property. Here, as examples, we prepared Ta3N5 photoanodes by an electrophoresis deposition (EPD) method and an oxidation and nitridation of Ta foil (ONTF) method. The light harvest, interfacial charge transfer, and charge separation of the two Ta3N5 photoanodes were analysed to gain insight into the role of the preparation method on the water splitting property. The results suggested that the ONTF-prepared Ta3N5 showed a higher solar energy conversion efficiency, arising from its better interfacial charge transfer efficiency and higher charge separation efficiency. The higher charge separation efficiency was mainly attributed to good electron transfer, and the inter-particle connectivity was key for the electron transfer in the photoanodes. Especially, the dense, small particle structure of ONTF-prepared Ta3N5 was beneficial for increasing the connectivity between inter-particles. This comparison of preparation methods can be used as a reference for future photoanode preparation to improve the water splitting property of photoelectrochemical cells.
Enhanced Spatial Charge Separation in a Niobium and Tantalum Nitride Core-Shell Photoanode: In Situ Interface Bonding for Efficient Solar Water Splitting

Beibei Zhang,Zeyu Fan,Yutao Chen,Chao Feng,Shulong Li,Yanbo Li

DOI: https://doi.org/10.1002/anie.202305123

2023-09-04

Abstract:Tantalum nitride (Ta3 N5 ) has emerged as a promising photoanode material for photoelectrochemical (PEC) water splitting. However, the inefficient electron-hole separation remains a bottleneck that impedes its solar-to-hydrogen conversion efficiency. Herein, we demonstrate that a core-shell nanoarray photoanode of NbNx -nanorod@Ta3 N5 ultrathin layer enhances light harvesting and forms a spatial charge-transfer channel, which leads to the efficient generation and extraction of charge carriers. Consequently, an impressive photocurrent density of 7 mA cm-2 at 1.23 VRHE is obtained with an ultrathin Ta3 N5 shell thickness of less than 30 nm, accompanied by excellent stability and a low onset potential (0.46 VRHE ). Mechanistic studies reveal the enhanced performance is attributed to the high-conductivity NbNx core, high-crystalline Ta3 N5 mono-grain shell, and the intimate Ta-N-Nb interface bonds, which accelerate the charge-separation capability of the core-shell photoanode. This study demonstrates the key roles of nanostructure design in improving the efficiency of PEC devices.
In Situ Hydrolysis Deposition of an Efficient Ta3N5 Microsphere Photoanode for Solar Water Splitting

Yang Li-Heng,Luo Wen-Jue,Li Ming-Xue,Zou Zhi-Gang

DOI: https://doi.org/10.11862/cjic.2016.330

2016-01-01

Abstract:A new in situ hydrolysis deposition method was used to prepare a Ta3N5 microsphere photoanode, which indicates a high photocurrent of 6.6 mA.cm(-2) at 1.6 V vs RHE. Microsphere precursor films are formed by hydrolysis of Ta(OEt)(5) and subsequent deposition on substrates, which is achieved by aging methanol solvent in air with high humidity. In contrast, no precursor films were obtained on substrates with fresh methanol. The results suggest that water in solvent is very essential to in situ depositing Ta3N5 photoanode. In addition, the facile method can be used to deposit Ta3N5 on other transparent conducting substrates.
NNaTaO3@Ta3N5 Core‐Shell Heterojunction with Controlled Interface Boosts Photocatalytic Overall Water Splitting

Kejian Lu,Fei Xue,Feng Liu,Mengfan Li,Wenlong Fu,Hao Peng,Chunyang Zhang,Jie Huang,Ze Gao,Hongwen Huang,Maochang Liu

DOI: https://doi.org/10.1002/aenm.202301158

IF: 27.8

2023-06-14

Advanced Energy Materials

Abstract:This work involves the facile and robust fabrication of a NNaTaO3@Ta3N5 core‐shell heterojunction with a light‐response range of up to 580 nm and apparent quantum yield for overall water splitting up to 6.28% at 550 nm. Ta3N5 is a promising material for photocatalytic hydrogen production from water because of its suitable band structure for both solar energy collection and overall water splitting, while its application is restricted by severe charge recombination as well as non‐equilibrium redox capabilities. Herein, atomic‐scale N‐doped NaTaO3@Ta3N5 (NNaTaO3@Ta3N5) core‐shell cubes prepared by nitridation of cubic NaTaO3 are reported. The core‐shell heterojunction cubes present efficient and stoichiometric evolution of H2 and O2 from photocatalytic overall water splitting, with a quantum efficiency of 2.18% at 550 nm without any cocatalyst. The success relies on the Ta3N5 shell having a thickness of only ≈5 nm which enables increased lifetimes of the photogenerated charges. Moreover, the core‐shell heterojunction shows a type‐I band alignment that can steer smooth charge flow from NNaTaO3 to Ta3N5, particularly with the assistance of the shared communal Ta atoms at the interface. This efficiency can be further improved to 6.28% by in situ deposition of a Rh@Cr2O3 core‐shell cocatalyst, which is among the highest reported values over Ta3N5‐based photocatalyst. This study offers a promising pathway for the construction of well‐defined heterojunctions with manipulated charge transfer behavior for photocatalytic overall water splitting.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,energy & fuels
Compensation of Band-Edge Positions in Titanium-Doped Ta 3 N 5 Photoanode for Enhanced Water Splitting Performance: A First-Principles Insight

Guozheng Fan,Xin Wang,Hongwei Fu,Jianyong Feng,Zhaosheng Li,Zhigang Zou

DOI: https://doi.org/10.1103/physrevmaterials.1.035403

IF: 3.98

2017-01-01

Physical Review Materials

Abstract:Ta3N5 is a promising photoanode for solar water splitting. However, it often suffers from high onset potential for water oxidation, which may be partially ascribed to the oxygen impurities in Ta3N5. Oxygen impurities, which are always introduced into Ta3N5 during the preparation process, are difficult to remove due to the low formation energy of O-doped Ta3N5. The valence-and conduction-band-edge positions shift almost in parallel towards more positive potentials with addition of oxygen impurities, which may increase the onset potential for water oxidation. In this study, the hybrid-DFT (density functional theory) calculations of Ti-doped Ta3N5 show that as Ti doping concentration increases, both the valence-and conduction-band-edge positions of Ta3N5 move towards more negative potentials, which is opposite to the role of oxygen impurties. In the case of Ti-O codoped Ta3N5, Ti doping can compensate the effect of oxygen impurities and may reduce the onset potential for water oxidation. Defect formation energies reveal that Ti-O codoped Ta3N5 is thermodynamically stable. Therefore we propose that by controlling the amount of O and Ti, the band-edge positions can be modified to a proper level so that better photoelectrochemical performances for solar water splitting can be achieved.
Manipulating a TiO2-graphene-Ta3N5 heterojunction for efficient Z-scheme photocatalytic pure water splitting

Fangyong Hou,Kejian Lu,Feng Liu,Fei Xue,Maochang Liu

DOI: https://doi.org/10.1016/j.materresbull.2022.111782

IF: 5.6

2022-06-01

Materials Research Bulletin

Abstract:Titanium dioxide (TiO2)-based photocatalysts are a class of hottest materials in solar water splitting, while limited achievements have been gained to date due to its broad band-gap only responding in UV region and sluggish charge transfer. Here, we reported a ternary TiO2-graphene-Ta3N5 hybrid photocatalyst synthesized via an ultrasonic-hydrothermal method. Compared with pristine TiO2 and Ta3N5, the prepared TiO2-graphene-Ta3N5 present remarkably enhanced photocatalytic pure water splitting behavior with an optimal H2-evolution rate of 180 μmol h−1 g−1. In conjunction with systematic characterizations, we demonstrated the boosted photocatalytic performance is ascribed to both improved visible light utilization and charge transfer behavior. Particularly, it is found that water splitting is achieved through a Z-scheme mechanism, in which the two-dimensional lamellar graphene served as a bridge accelerating the electron transfer from TiO2 to Ta3N5. This work opens avenues to design efficient TiO2-based photocatalyst by embedding conducting layer for rapid electron transfer during solar-fuel conversion.

materials science, multidisciplinary
Enhanced Charge Separation by Oriented Growth of Ta3N5-Cu2O N-P Array Heterojunction

Hongxu Wang,Zhan Shi,Shicheng Yan,Zhigang Zou

DOI: https://doi.org/10.1063/1.5092646

IF: 4

2019-01-01

Applied Physics Letters

Abstract:Tantalum nitride (Ta3N5) is one of the most promising photoresponsive semiconductor materials for efficient solar energy conversion, but its fast carrier recombination has hindered research progress severely. Fabricating a heterojunction structure is an effective strategy to promote the charge separation efficiency and thus enhance solar conversion efficiency. Herein, we designed a p-n heterojunction photoanode consisting of n-type Ta3N5 nanorod arrays (NRAs) that grew along the a-axis (light electron effective mass) and p-type Cu2O nanoparticles. This NRA heterojunction shortens the hole diffusion distance, transfers electrons along the a-axis effectively, and enlarges the space charge region. The heterojunction improves the charge separation efficiency of Ta3N5 NRAs significantly, and Ta3N5-Cu2O exhibits a photocurrent density of 9.19 mA cm(-2) at 1.6 V vs normal hydrogen electrode (V-NHE, pH = 0), an onset potential of 0.326 V-NHE, and a maximum incident photon to current efficiency of 60% at 380 nm. Our results demonstrated a potential crystal oriented growth strategy of nanostructured heterojunctions for overcoming the short carrier diffusion distance and fast carrier recombination. Published under license by AIP Publishing.
Molten Salt-Assisted A-Axis-oriented Growth of Ta3N5 Nanorod Arrays with Enhanced Charge Transport for Efficient Photoelectrochemical Water Oxidation

Zhan Shi,Zhe Xu,Jianyong Feng,Huiting Huang,Qinfeng Qian,Shicheng Yan,Zhigang Zou

DOI: https://doi.org/10.1039/c8ce01016a

IF: 3.756

2018-01-01

CrystEngComm

Abstract:Efficiently harvesting light and transporting charges are the main challenges for solar water oxidation by Ta3N5 photoanodes. Herein, we discovered a facile KI molten salt route to fabricate highly oriented Ta3N5 nanorod arrays along the [100] crystallographic direction. The size of the nanorods can be finely tuned by controlling the amount of KI flux due to their bottom-up growth mechanism. The array structure enhances the light scattering, which is beneficial for harvesting more light to make up for the light absorption anisotropy of Ta3N5. The preferred [100] growth orientation guarantees electron migration to the substrate, and the enlarged space charge layer facilitates hole migration to the semiconductor-liquid interface. As a result, under AM 1.5 irradiation, the onset potential of the Ta3N5 nanorod array photoanode reaches 0.65 V versus reversible hydrogen electrode, and the current density reaches 4.65 mA cm(-2). The design concept that rationally combines the advantages of charge transport and light utilization may offer a new strategy for efficient solar energy conversion.

Carrier engineering of Zr-doped Ta<sub>3</sub>N<sub>5</sub> film as an efficient photoanode for solar water splitting

Carrier Engineering of Zr-doped Ta3N5 Film As an Efficient Photoanode for Solar Water Splitting

Interface Engineering of Ta3N5 Thin Film Photoanode for Highly Efficient Photoelectrochemical Water Splitting

Engineering band structure via dual atoms modification for the efficient photoanode

Ge-mediated modification in Ta3N5 photoelectrodes with enhanced charge transport for solar water splitting.

Decoupling light absorption and carrier transport via heterogeneous doping in Ta3N5 thin film photoanode

Enhanced Water‐Splitting Performance of Perovskite SrTaO2N Photoanode Film Through Ameliorating Interparticle Charge Transport

Band structure engineering and defect control of Ta3N5 for efficient photoelectrochemical water oxidation

LaCl3 Flux Mediated Ta3N5 Planar Photoanode for Solar Water Oxidation

A co-catalyst-loaded Ta(3)N(5) photoanode with a high solar photocurrent for water splitting upon facile removal of the surface layer.

Surface Chemistry and Photoelectrochemistry-Case Study on Tantalum Nitride.

A Co-catalyst-Loaded Ta<sub>3</sub>N<sub>5</sub>Photoanode with a High Solar Photocurrent for Water Splitting upon Facile Removal of the Surface Layer

What Limits the Performance of Ta3N5 for Solar Water Splitting

Charge Carrier Transfer in Ta3n5 Photoanodes Prepared by Different Methods for Solar Water Splitting

Enhanced Spatial Charge Separation in a Niobium and Tantalum Nitride Core-Shell Photoanode: In Situ Interface Bonding for Efficient Solar Water Splitting

In Situ Hydrolysis Deposition of an Efficient Ta3N5 Microsphere Photoanode for Solar Water Splitting

NNaTaO3@Ta3N5 Core‐Shell Heterojunction with Controlled Interface Boosts Photocatalytic Overall Water Splitting

Compensation of Band-Edge Positions in Titanium-Doped Ta 3 N 5 Photoanode for Enhanced Water Splitting Performance: A First-Principles Insight

Manipulating a TiO2-graphene-Ta3N5 heterojunction for efficient Z-scheme photocatalytic pure water splitting

Enhanced Charge Separation by Oriented Growth of Ta3N5-Cu2O N-P Array Heterojunction

Molten Salt-Assisted A-Axis-oriented Growth of Ta3N5 Nanorod Arrays with Enhanced Charge Transport for Efficient Photoelectrochemical Water Oxidation