Abstract:Eutectic microstructures are one of the most common solidification patterns in the binary or multi-component alloy systems. Due to the fine periodic microstructures of the eutectic alloys, the commercial applications of the eutectic alloys can improve the mechanical properties of the castings. The solidification mechanism of eutectic alloys has been widely studied by a lot of experimental works and theoretical analysis over the years. Recently, numerical models were used to study the mechanisms of formation of phase patterns and selection dynamics of the lamellar eutectic, such as phase field (PF) and cellular automaton (CA) model, which can promote the development of eutectic growth theory. Based on the existing CA method for binary primary a phase, a modified cellular automaton (MCA) model was developed for the simulation of binary eutectic growth. In this model, the influence of constitutional and curvature undercooling on the interface morphology was considered. The growth rate of eutectic interface was calculated by the solute conservation at the alpha/liquid and beta/liquid interfaces. The model could simulate the phenomenon of overgrowth, splitting and steady state growth of the eutectic lamellar. CBr4-C2Cl6 eutectic transparent alloy was chosen to validate the model. The simulated results showed that the increasing pulling rate lead to a smaller eutectic lamellar spacing, which had a good agreement with the Jackson-Hunt theory and the experimental results from the literature. Eutectic morphology evolution was simulated under a constant pulling rate and temperature gradient, which showed that the stable lamellar structures existed when the initial lamellar spacing was in a finite range between the minimum stable spacing lambda(m) and the limiting maximum stable spacing lambda(M). A smaller initial lamellar spacing would lead to lamellar annihilation. Conversely, a larger initial lamellar spacing could lead to the lamellar nucleation due to the appearance of solute rich concave at the center of the alpha/liquid interface. Meanwhile, the oscillatory instability of the eutectic lamellar was also reappeared by the MCA model. The MCA model was easily extended to 3D, and the lamellar rod transition during directional solidification was simulated, which showed that the ratio of volume fraction of alpha and beta phase was smaller than 1/pi tend to form lamellar rod transition when the initial lamellar spacing was smaller than lambda(m).

Three-dimensional cellular automaton models of microstructural evolution during solidification

Modeling of Dendritic Structure During Solidification Process Based on Cellular Automaton Model

Numerical Modelling Of Microstructure Evolution And Dendrite Growth In Alloy Solidification Process

A Cellular Automaton Technique for the Modeling of Solidification Microstructure in Multi-Component Alloys

Microstructure evolution during dendrite coarsening in an isothermal environment: 3-D cellular automaton modeling and experiments

A Three-Dimensional Cellular Automaton Model of Dendrite Growth with Stochastic Orientation During the Solidification in the Molten Pool of Binary Alloy

A Modified Cellular Automaton Method for the Modeling of the Dendritic Morphology of Binary Alloys

The Impact of Two and Three Dimensional Assumptions on Coupled Structural Mechanics and Microstructure Solidification Modelling

3D Modeling and Simulation of Dendritic Growth During Solidification

Low artificial anisotropy cellular automaton model and its applications to the cell-to-dendrite transition in directional solidification

Neural Cellular Automata for Solidification Microstructure Modelling

Cellular Automaton Simulation and Experimental Validation of Eutectic Transformation During Solidification of Al-Si Alloys

Research situation of material microstructure simulation using cellular automata

A Three-Dimensional Cellular Automaton Model for Simulation of Dendritic Growth of Magnesium Alloy

Three Dimensional Numerical Simulation of Solidification Microstructure of Single Phase Alloy

Modeling and Simulation of Dendrite Growth in Solidification of Al-Si-Mg Ternary Alloys

Three-dimensional Numerical Simulation of Meso-Scale Dendritic Growth in Alloys

Simulation of Eutectic Growth in Directional Solidification by Cellular Automaton Method

A Cellular Automaton Technique for Modelling of a Binary Dendritic Growth with Convection

Cellular Automaton Simulation of Peritectic Solidification of a C-Mn Steel

Numerical simulation on solidification microstructure of cast steel using cellular automaton method