Abstract:Eutectic microstructures are one of the most common solidification patterns in the binary or multi-component alloy systems. Due to the fine periodic microstructures of the eutectic alloys, the commercial applications of the eutectic alloys can improve the mechanical properties of the castings. The solidification mechanism of eutectic alloys has been widely studied by a lot of experimental works and theoretical analysis over the years. Recently, numerical models were used to study the mechanisms of formation of phase patterns and selection dynamics of the lamellar eutectic, such as phase field (PF) and cellular automaton (CA) model, which can promote the development of eutectic growth theory. Based on the existing CA method for binary primary a phase, a modified cellular automaton (MCA) model was developed for the simulation of binary eutectic growth. In this model, the influence of constitutional and curvature undercooling on the interface morphology was considered. The growth rate of eutectic interface was calculated by the solute conservation at the alpha/liquid and beta/liquid interfaces. The model could simulate the phenomenon of overgrowth, splitting and steady state growth of the eutectic lamellar. CBr4-C2Cl6 eutectic transparent alloy was chosen to validate the model. The simulated results showed that the increasing pulling rate lead to a smaller eutectic lamellar spacing, which had a good agreement with the Jackson-Hunt theory and the experimental results from the literature. Eutectic morphology evolution was simulated under a constant pulling rate and temperature gradient, which showed that the stable lamellar structures existed when the initial lamellar spacing was in a finite range between the minimum stable spacing lambda(m) and the limiting maximum stable spacing lambda(M). A smaller initial lamellar spacing would lead to lamellar annihilation. Conversely, a larger initial lamellar spacing could lead to the lamellar nucleation due to the appearance of solute rich concave at the center of the alpha/liquid interface. Meanwhile, the oscillatory instability of the eutectic lamellar was also reappeared by the MCA model. The MCA model was easily extended to 3D, and the lamellar rod transition during directional solidification was simulated, which showed that the ratio of volume fraction of alpha and beta phase was smaller than 1/pi tend to form lamellar rod transition when the initial lamellar spacing was smaller than lambda(m).

Low artificial anisotropy cellular automaton model and its applications to the cell-to-dendrite transition in directional solidification

A Cellular Automaton Model for the Solidification of a Pure Substance

A Modified Cellular Automaton Model For Simulation Of Dendritic Microstructures In Solidification Of Alloys

A Cellular Automaton Model with the Lower Mesh-Induced Anisotropy for Dendritic Solidification of Pure Substance

Quantitative cellular automaton model and simulations of dendritic and anomalous eutectic growth

A Cellular Automaton Technique for the Modeling of Solidification Microstructure in Multi-Component Alloys

Effects of Physical Parameters on the Cell-To-Dendrite Transition in Directional Solidification

Three-dimensional cellular automaton models of microstructural evolution during solidification

Orientation selection of equiaxed dendritic growth by three-dimensional cellular automaton model

Development of a CA-FVM Model with Weakened Mesh Anisotropy and Application to Fe–C Alloy

Numerical Simulation of Microstructure Evolution During Alloy Solidification by Using Cellular Automaton Method

A Modified Cellular Automaton Model For The Simulation Of Dendritic Growth In Solidification Of Alloys

Field Variable Diffusion Cellular Automaton Model for Dendritic Growth with Multifold Symmetry for the Solidification of Alloys

A Three Dimensional Modified Cellular Automaton Model for the Prediction of Solidification Microstructures

Simulation of Eutectic Growth in Directional Solidification by Cellular Automaton Method

A Modified Cellular Automaton Method for the Modeling of the Dendritic Morphology of Binary Alloys

Restrictions of Physical Properties on Solidification Microstructures of Al-based Binary Alloys by Cellular Automaton

2-D Cellular Automation Modeling for Grain Growth-Coarsening During Solidification

Microstructure evolution during dendrite coarsening in an isothermal environment: 3-D cellular automaton modeling and experiments

Understanding Solidification of Near Eutectic Alloy Using Cellular Automata (CA)

A New Coupled Model for Alloy Solidification