Abstract:The effect of major constituents (the Li content increases from 0.5 to 3 wt% and the Cu content decreases from 4.5 to 2 wt%) on microstructure and mechanical properties of cast Al-Li-Cu-Zr alloy were studied to understand a qualitative assessment of sequence and kinetics of multiple precipitations. Increasing the Li content progressively raises the melting temperature from 520 °C in 1# alloy (Al-0.5Li-4.5Cu, wt%) and 2# alloy (Al-1Li-4.5Cu) to 560 °C in 6# alloy (Al-3Li-2Cu). In addition, the variations of the major constituents result in the changes of the type and volume fraction of the inter- and intra-granular intermetallic phases. TEM results indicate that minor modifications to alloy composition greatly alter precipitation behavior during isothermal aging. The Li-poor alloy (2# alloy) presents a much shorter incubation time of T1-Al2CuLi precipitate than the Li-rich alloy (Al-1.5Li-4.5Cu, 3# alloy), while the nucleation of θ'-Al2Cu precipitate is promoted in Li-rich alloy. No typical spherical δ'-Al3Li precipitate is observed in 2# and 3# alloys during isothermal aging, except for the as-quenched 3# alloy. The preferential nucleation of δ' precipitate on the coherent and broad face of θ' precipitate is observed in 2# and 3# alloys, leading to the formation of "sandwich-like" δ'/θ'/δ' phases. Further decreasing Cu content to 2 wt% and increasing Li content to 3 wt% (6# alloy), the predominant phase in the matrix is δ' precipitate, accompanied by a small amount of unevenly distributed θ' and T1 precipitates. The best balance between ductility and strength is obtained by 2# alloy aged for 32 h, but 6# alloy has significant advantages in terms of density (2.437 g/cm3) and elastic modulus (82.65 GPa) over 2# alloy (density: 2.675 g/cm3; elastic modulus: 75.45 GPa).

Effect of Composition on Microstructure and Properties of As-Cast 2196 Al–Cu–Li Alloy

Influence of enhanced Li content on the as-cast eutectic phase features and the evolution during homogenization of Al-Cu-Li alloys

Microstructure and Mechanical Properties of Cast Al-Li-Mg Alloy: Role of Cu Addition and Heat Treatment

Microstructural Evolution of Al-Cu-Li Alloys with Different Li Contents by Coupling of Near-Rapid Solidification and Two-Stage Homogenization Treatment

The effect of major constituents on microstructure and mechanical properties of cast Al-Li-Cu-Zr alloy

Effect of Sc and Zr on Microstructure and Mechanical Properties of As‐Cast Al–Li–Cu Alloys

Influences of Mg content on the microstructures and mechanical properties of cast Al–2Li–2Cu–0.2Zr alloy

Microstructure Evolution and Mechanical Properties of a Cast and Heat-Treated Al–Li–Cu–Mg Alloy: Effect of Cooling Rate During Casting

Effect of Li on Microstructures and Properties of Al-3.5Cu-1.5Mg Alloy

Effect of Composition on the Microstructure and Mechanical Properties of Mg–Zn–Al Alloys

Experimental Investigation and Simulation Assessment on Fluidity and Hot Tearing Susceptibility of Al-Li-Cu-X Alloy: the Role of Microalloying Elements

Microstructural characteristics and mechanical properties of cast Al-3Li-xCu-0.2Zr alloy

Effect of Li Content on Properties and Microstructure Evolution of Near-Rapid Solidified 2A97 Al-Li Alloy

Effect of minor Ag addition on microstructures and properties of Al-Mg-Cu-Li alloy with low Cu/Mg ratio

Effect of Ti content on microstructures and mechanical properties of cast Al-2Li-2Cu-0.5Mg alloy

Effect of composition on the microstructure and mechanical properties of Mg-Al-Zn alloys

The influence of small additions of silver and magnesium on microstructure and properties of Al-Li-Cu system alloys

Role of Cu on the Mechanical Properties and Microstructures Evolution of Al-xCu-1Li-0.4Mg–1Zn-0.1Zr Alloys

Influences of Mn Content on the Microstructures and Mechanical Properties of Cast Al-3Li-2Cu-0.2Zr Alloy

Effects of Sc Addition on the Microstructure and Mechanical Properties of Cast Al-3Li-1.5Cu-0.15Zr Alloy

Evaluation of Cu Content on Mechanical Performance and Castability of AlMg5.4Si2 Alloy