Abstract:Due to the difference between original material and the processed material for use in turbine blades, re-search that solely focuses on the original materials may not fully explain the performance of operational turbine blades. In order to ensure the maximum utilization rate of turbine blades, the study examines the creep properties and differences of different parts of the directional solidification of original casting turbine blades. In this article, a set of sampling fixtures from different parts of a turbine blade were proposed to quantitatively measure the difference in creep properties caused by the complex geometric factors created during the DS process. The special fixtures would cut the blades into five different parts, which were to be further processed into small samples. Creep tests under two different conditions (980 degrees C/245 MPa, 980 degrees C/ 267 MPa) were carried out. Round rod specimens (standard parts) were used for creep tests under the same conditions for comparison. By employing scanning electron microscopic (SEM) and creep tests on different parts of original casting turbine blades, the mechanism of microstructure evolution and the creep fracture behavior were proposed in this condition. In addition, the original microstructure of different parts of a blade was observed by scanning electron microscopy (SEM), and the characteristics of the different parts were simulated based on an improved two-parameter creep constitutive model. The results suggest that the creep life of the different parts of the original casting blade is different, which caused by the differences in microstructure and morphology of the different parts of the original casting blade. The creep property of standard parts is better than that of original casting blades. The creep life of original casting blades from small to large is as follows: CVS, DP, LE, CCS, TT. An improved two-parameter creep constitutive model was adopted to simulate the difference in creep properties (including creep life) resulted from different parts in a turbine blade. This difference needs to be considered in designing the structure and service life of turbine blades formed by directional solidification. The research results are of great significance for improving the design of directionally solidified turbine blades and for improving the directional solidification forming process. (c) 2021 Elsevier B.V. All rights reserved.

Degradation of Microstructural and Mechanical Properties with Serviced Turbine Blades

Degradation Behavior of Microstructures and Mechanical Properties of GTD111 Turbine Blade After Long-Term Service

Microstructure Degradation of Service-Exposed Turbine Blades Made of Directionally Solidified DZ125 Superalloy

Dependence of Microstructural Evolution on the Geometric Structure for Serviced DZ125 Turbine Blades

Creep Characteristics of Directionally Solidified Turbine Blades Based on the Difference in Original Casting Characteristics

Assessment of service induced degradation of microstructure and properties in turbine blades made of GH4037 alloy

Service Induced Degradation and Rejuvenation of Gas Turbine Blades

Experimental Investigation on Creep‐fatigue Behaviours of As‐received and Service‐exposed Turbine Blades: Mechanism and Life Evaluation

Mechanical Properties Deterioration and Its Relationship with Microstructural Variation Using Small Coupons Sampled from Serviced Turbine Blades

Structural Degradation and Elemental Variations in an Ex-Service First-Stage Gas Turbine Blade

Study on Mechanical Properties of DZ125 Directional Solidification Turbine Blades in Different Positions

Residual Lifetime Assessment Model Based on Microstructural Evolution of Service-Exposed DZ125 Turbine Blades

Evaluation of Service-Induced Microstructural Damage for Directionally Solidified Turbine Blade of Aircraft Engine

A Multi-Scale Framework for Life Reduction Assessment of Turbine Blade Caused by Microstructural Degradation

Creep analysis and service life prediction of turbine blade with progressive damage

Experimental Investigation On The Creep And Low Cycle Fatigue Behaviors Of A Serviced Turbine Blade

Direct Investigation on High Temperature Tensile and Creep Behavior at Different Regions of Directional Solidified Cast Turbine Blades

ICME Framework for Damage Assessment and Remaining Creep Life Prediction of In-Service Turbine Blades Manufactured with Ni-Based Superalloys

Microstructure degradation and residual low cycle fatigue life of a serviced turbine blade

Crystallographic Life Model for Single Crystal Turbine Blade and Validation by the Miniature Specimens Cut from the Turbine Blades

An Integrated Creep Damage Analysis Method of Turbine Blades Based on the Service History