Abstract:The microstructural evolution of K4750 nickel-based superalloy with different hafnium (Hf) contents was investigated by thermodynamic calculations (TC) and experiments. According to TC, with the increases of Hf content from 0 wt% to 1.5 wt%, the redissolving temperature of MC carbide first decreased rapidly and then tended to be relatively stable, the precipitated temperature of M23C6 carbide decreased gradually, while the gamma ' weight fraction increased first and then stabilized. Three alloys containing 0 wt%, 0.11 wt%, and 0.28 wt% Hf were then prepared to further study the evolution of the microstructure. The experimental results showed that the increase of Hf content changed the morphology of MC carbide from long strip to rodlike and blocky, which is caused by the decrease of Ti and Nb contents and the increase of Hf content in MC carbides. The addition of Hf also changed the morphology of M23C6 carbide from continuous to granular due to the different MC distribution at grain boundaries (GBs). In addition, a small amount of Hf segregated into the gamma ' phase, reducing the Al and Nb contents of the gamma ' phase, resulting in an increased gamma/gamma ' lattice mismatch. As the Hf content increased from 0 wt% to 0.11 wt% and 0.28 wt%, the mean stress rupture life at 750 degrees C and 430 MPa increased from 99.54 h to 105.73 h and 170.96 h, which was closely related to the evolution of MC, M23C6 and gamma ' precipitates. Therefore, the relationship between microstructure and stress rupture properties was discussed in detail.

Existence Form and Distribution of Mn and the Effect of Mn Content on High-Temperature Stress Rupture Proper-ties of K417G Superalloy

Effect of cyclic straining at elevated-temperature on static mechanical properties, microstructures and fracture behavior of nickel-based superalloy GH4145/SQ

In-Situ Study of High Temperature Tensile Fracture Mechanism of Mar-M247 Alloy

Effect of Hafnium Content on the Microstructural Evolution and Stress Rupture Properties of K4750 Nickel-Based Superalloy

Effect of Melt Superheating Treatment on the Microstructure and High Temperature Stress Rupture Properties of M963 Superalloy

New insights into the stress rupture life enhancement mechanisms of a nickel-based superalloy

Effect of N Content on Microsegregation, Microstructure and Mechanical Property of Cast Ni-Base Superalloy K417g

Effect of Mn content on low-cycle fatigue behaviors of low-carbon bainitic steel

High temperature creep behavior and damage mechanism of an advanced PM Ni‐based superalloy

Primary MC Decomposition and Its Effects on the Rupture Behaviors in Hot-Corrosion Resistant Ni-based Superalloy K444

Effects of B content on microstructure and high-temperature stress rupture properties of a high chromium polycrystalline nickel-based superalloy

Effects of Mn addition on mechanical properties, fracture surface, and electrochemical corrosion resistance of CoCrFeNiAl high-entropy alloys

Effect of Microstructure on High Temperature Mechanical Properties in Forming Ni-20cr-10mo-10co Superalloy

Mechanical Properties and Fracture Analysis of Mn-Rich Ni-Mn-Ga Polycrystalline Alloys

Avoiding microstructural instabilities in high tungsten containing superalloys by adjusting Al content

Effect of Mn content on microstructure and properties of 6000 series aluminum alloy

Tensile, Creep Behavior and Microstructure Evolution of an As-Cast Ni-based K417G Polycrystalline Superalloy

Effect of Cooling Rate on Microstructure, Microsegregation and Mechanical Properties of Cast Ni-based Superalloy K417G

Improved 1200 °C Stress Rupture Property of Single Crystal Superalloys by Γ′-Forming Elements Addition

Effect of Mn Addition on Microstructure and Mechanical Properties of Cast Al-2li-2cu-0.8mg-0.4zn-0.2zr Alloy

Influence of Mn Addition on the Microstructure and Mechanical Properties of a Directionally Solidified Γ-Tial Alloy