Abstract:In this study, a comprehensive examination was conducted to explore the technology involved in the recovery of waste heat from flue gas emitted by a 1000 MW unit. Traditional methods are constrained in their ability to harness waste heat from flue gas solely for the purpose of generating medium-temperature water. The system being examined not only recovers waste heat but also utilizes it to generate steam, thereby greatly improving resource efficiency. The process entails utilizing the flue gas to heat water to a certain temperature, followed by subjecting it to flash evaporation. This process leads to the generation of low-pressure waste heat steam. Within the steam ejector, the waste heat steam combines with high-pressure motive steam extracted from the source, resulting in the formation of medium-pressure steam. Within the steam ejector, the waste heat steam blends with high-pressure motive steam drawn from the source, forming medium-pressure steam that eventually feeds into the A8 steam extraction pipe (low-pressure turbine pumping pipe). The present study examines the fluctuation patterns in motive steam flow, suction coefficient, waste heat steam volume, and outlet temperature of the flue water heat exchanger when different motive steam sources are used. Additionally, the research calculates the reduction in CO2 emissions, the coal consumption for power supply, and the cost savings in fuel for the retrofitted system. The findings indicate that maximizing energy utilization can be achieved by operating the retrofitted unit at the lowest feasible waste heat steam pressure. The implementation of the new system has resulted in a substantial decrease in coal consumption for power supply. When employing main steam as the extraction steam source, the consumption of coal for power generation decreases in proportion to the decrease in waste heat steam pressure while maintaining a constant unit load. When the waste heat steam pressure reaches 0.0312 MPa, the recorded coal consumption for power generation varies between 289.43 g/kWh at 100% turbine heat acceptance (THA) and 326.94 g/kWh at 30%THA. When comparing this performance with the initial thermal power plant (TPP) unit, it demonstrates reductions of 2.26 g/kWh and 1.52 g/kWh, respectively. After implementing modifications to this 1000 MW unit, it is projected that the annual CO2 emissions can be effectively reduced by 6333.97 tons, resulting in significant cost savings of approximately USD 0.23 million in fuel expenses. This system exhibits considerable potential in terms of emission reduction and provides valuable insights for thermal power plants aiming to decrease unit energy consumption.

Different Cases Study on the Heating Surface Layout of a New 600 MWe Coal-Fired Power Plant Coupled with CaO-based Carbon Capture System Based on Heat Exchanger Network

Advanced Exergoenvironmental Evaluation for a Coal-Fired Power Plant of Near-Zero Air Pollutant Emission

Thermodynamic and economic analysis of a new 600 MWe coal-fired power plant integrated with CaO-based carbon capture system

Study on heat integration of supercritical coal-fired power plant with post-combustion CO2 capture process through process simulation

An integrated de-carbonization supercritical coal-fired power plant incorporating a supplementary steam turbine, process heat recovery and a modified boiler structure

Thermal economy simulation study for a carbon capture power plant with combined heat and power based on absorption heat pump technology

The Heat Transfer Coefficients of the Heating Surface of 300 MWe CFB Boiler

Analytical and numerical investigations on the high temperature upgrading solution of subcritical boilers

Research and Design Experience of a 150 Kt/A Co2 Capture and Purification Project in the Shaanxi Guohua Jinjie Power Plant

Analysis of heating load distribution and operation optimization for 350MW high back pressure double extraction series units

Study And Design Of Platen Superheater Of 300 Mw Cfb Boiler

Upgrading the Integration of Supercritical Coal-Fired Power Plant with Post-Combustion CO<SUB Align="right">2 Capture Process Through Process Simulation

Performance Analysis and Optimization of Flue Gas Waste Heat Recovery System of a 600MW Coal-Fired Power Plant

Thermodynamics, flexibility and techno-economics assessment of a novel integration of coal-fired combined heating and power generation unit and compressed air energy storage

Analysis of an Exhaust Heat Recovery Process of Integrating Bypass Flue and Condensate Air Heater for Efficient Power Generation

Optimization study of CO 2 capture unit for subcritical coal-fired power generation unit based on Ebsilon and Aspen plus

Design and optimization of waste heat recovery system for supercritical carbon dioxide coal-fired power plant to enhance the dust collection efficiency

Layout Comparison and Parameter Optimization of Supercritical Carbon Dioxide Coal-Fired Power Generation Systems under Environmental and Economic Objectives

An Ejector and Flashbox-Integrated Approach to Flue Gas Waste Heat Recovery: A Novel Systematic Study

Comparative study on process simulation and performance analysis in two pressurized oxy-fuel combustion power plants for carbon capture

Development and testing of a new post-combustion CO2 capture solvent in pilot and demonstration plant