Abstract:In this paper, a novel droplet + arc additive manufacturing (DAAM) has been proposed for building aluminum alloy components with high quality and high efficiency. A special droplet generation system (DGS) was designed to replace the traditional wire feeding system, making the material addition process and the arc heat input process two independent parts. During the DAAM process, the arc heat source with variable polarity is arranged tilted below the DGS, the droplets which generated from DGS drop vertically and sequentially into the molten pool, and the aluminum alloy component can be deposited layer-by-layer by moving substrate. The droplet generation process, droplet + arc deposition process, as well as the heat input strategy, microstructure and mechanical properties of the thin-wall component are discussed in detail. The experimental results show that the small and sequential droplet generation mode is beneficial to improve the continuity of deposition process and significantly reduce the harmful impact of droplets on the molten pool. Meanwhile, the DAAM process shows great inclusiveness of droplet falling deviation. A multi-layer thin-wall component and a ring-shaped structure were fabricated successfully by DAAM with the deposition rate of 140 mm3/s. The microstructure of the thin -wall component is dominated by columnar crystals and it has obvious periodic distribution along the deposi-tion direction. The tilted growth of columnar crystals results in different grain morphology in the cross section and longitudinal section. After T6 heat treatment, the average ultimate tensile strength (UTS) and elongation in the horizontal direction are 435.0 MPa and 10.4%, while the average UTS and elongation in the vertical direction are 406.5 MPa and 16.4%, respectively. The fracture morphology is dominated by ductile fracture, but it exhibits some intergranular fracture characteristic in the horizontal direction. This novel DAAM provides a new choice for additive manufacturing of aluminum alloy, and shows great potential for the simultaneous improvement of the manufacturing quality and efficiency.

Influence of High-Melting Particle Implantation on Microstructure of Al Alloy Thin-Wall Components Fabricated by Droplet + Arc Additive Manufacturing

Investigation of Droplet+Arc Deposition Additive Manufacturing with WCp Simultaneous Reinforcement for Aluminum Alloy

Microstructure and mechanical properties of Al-Cu alloy during wire and arc additive manufacturing by adding micron TiB2 particles

Particle Distribution and Interfacial Reaction of WC Reinforced Titanium Matrix Composites Fabricated by Wire and Arc Additive Manufacturing

A Novel Droplet + Arc Additive Manufacturing for Aluminum Alloy: Method, Microstructure and Mechanical Properties

Effect of Alloying Powders on Microstructure and Mechanical Properties of Aluminum Alloy Arc Additive Manufacturing

Fabrication of γ-TiAl intermetallic alloy using the twin-wire plasma arc additive manufacturing process: Microstructure evolution and mechanical properties

Realization of synergistic enhancement for fracture strength and ductility by adding TiC particles in wire and arc additive manufacturing 2219 aluminium alloy

Contribution Made by Double-Sized TiC Particles Addition to the Ductility–strength Synergy in Wire and Arc Additively Manufactured Al–Cu Alloys

A novel magnetic field assisted powder arc additive manufacturing for Ti60 titanium alloy: Method, microstructure and mechanical properties

Heterogeneous microstructure evolution in Ti-6Al-4V alloy thin-wall components deposited by plasma arc additive manufacturing

Fabrication of Titanium Aluminides via Powder-Cored Wire Arc Additive Manufacturing: Microstructural and Mechanical Characterization

Microstructures and Properties of Al-Mg Alloys Manufactured by WAAM-CMT

Effect of Al–5Ti–1B grain refiner on microstructure and properties of arc-additive-manufactured Al–Mg alloy

Hierarchical Grain Refinement During the Laser Additive Manufacturing of Ti-6Al-4V Alloys by the Addition of Micron-Sized Refractory Particles

Fabrication of Fe–30Al alloy using plasma arc welding powered twin-wire directed energy deposition-arc process: Droplet transfer, microstructure, and mechanical property investigation

Influence of AlSi10Mg Particles Microstructure on Heat Conduction During Additive Manufacturing

Controlling the Microstructure and Properties of Ti-6.5al-2zr-1mo-1v Components Fabricated by High-Deposition-Rate Wire Arc Additive Manufacturing

Microstructure Modification of Twin-Wire Directed Energy Deposition-Arc Fabricated Γ-Tial Alloy Via Deposition Current Control

Microstructure and Properties of Al-6.0Mg-0.3Sc Alloy Deposited by Double-Wire Arc Additive Manufacturing

Improvement of microstructure and mechanical properties of CMT wire arc additive manufacturing Al-Si alloy deposition via interlayer coating TiC nanoparticles