Abstract:Strict regulations on fuel economy are driving modern gasoline engines to adopt more advanced technologies to improve thermal efficiency. Some of the technologies, for example ultra-high compression ratio and spark assisted compression ignition, will elevate the thermodynamic condition near top dead center (TDC) to a considerably high level, even up to or beyond the negative temperature coefficient (NTC) region. This will definitely increase knock tendency when the combustion is not well controlled. Previous knock-related research mainly focused on temperature ranges in/below the NTC region, while the knock combustion beyond the NTC region has rarely been studied. To understand the knock behavior beyond the NTC region, in this study the flame propagation process and end-gas auto-ignition of iso-octane under wide thermodynamic conditions across the NTC region were optically studied using dual-camera photography. The results showed that the flame propagation speed increased with increasing initial temperature and decreasing initial pressure, exhibiting no NTC characteristic. With the intervention of flame propagation, the residence time of the end-gas was shortened as the initial thermodynamic conditions were promoted, indicating no NTC behavior in the overall ignition delay time of the end-gas. Two kinds of detonation initiation processes were identified. In the cases strongly affected by low temperature chemistry (LTC), the auto-ignition showed a two-stage characteristic during which a widespread but relatively weak auto-ignition (first-stage) was observed prior to the final detonation initiation. In contrast, when the LTC was absent, the detonation was initiated directly in a single auto-ignition event. Lower initial energy densities were needed to initiate detonation in the cases less affected by LTC. Thermodynamic analyses based on Bradley's ε-ξ diagram showed that, for the LTC-affected cases, the pressure rise which resulted from the widespread weak first-stage auto-ignition had vital impacts on the final detonation initiation by shifting the ε-ξ location into or away from the detonation region. Finally, thermal diffusivity was demonstrated to be capable of distinguishing detonation from other combustion modes as detonation tended to occur with lower thermal diffusivities of the mixture.

Research on Destructive Knock Combustion Mechanism of Heavy-Duty Diesel Engine at Low Temperatures

New Insights into Abnormal Combustion Phenomena Induced by Diesel Spray-Wall Impingement under Engine-Relevant Conditions

Study on Impinging Ignition and Wall-Attached Fuel Film Combustion Characteristics of Light- to Heavy-Duty Diesel Engines at Low Temperatures

Acting Mechanism of Low Ambient Temperature on Wall-Impinging Diesel Spray Ignition at an Extensive Range

Effect of Injection Pressure and Fuel Mass on Wall-Impinging Ignition and Combustion Characteristics of Heavy-Duty Diesel Engine at Low Temperatures

Wall Temperature Effects on Ignition Characteristics of Liquid-phase Spray Impingement for Heavy-duty Diesel Engine at Low Temperatures

Effect of Injection Timing on Knock Combustion and Pollutant Emission of Heavy-Duty Diesel Engines at Low Temperatures

A Numerical Investigation of Injection Pressure Effects on Wall-Impinging Ignition at Low-Temperatures for Heavy-Duty Diesel Engine

Thermal Load Analysis of Piston Damaged by Wall-Wetting Combustion in a Heavy-Duty Diesel Engine

Effect of Wall Parameters on Impinging Combustion and Soot Emission Characteristics of Heavy-Duty Diesel Engine at Low Temperature

Optical experiments on diesel knock for high altitude engines under spray impingement conditions

Effects of Low Temperature on Near-Nozzle Breakup and Droplet Size Distribution in Airblast Kerosene Spray

Effect of Injection Pressure on the Impinging Spray and Ignition Characteristics of the Heavy-Duty Diesel Engine under Low-Temperature Conditions

Numerical Study of Wall-Impinging Ignition at Different Wall Distances for Cold Start of Heavy-Duty Diesel Engine

Experimental Study on the Combustion Characteristics of Impinging Diesel Spray at Low Temperature Environment

Study on the forming process of the cylinder wall fuel film and the piston top land ablation mechanism of a medium speed marine diesel engine under cold start condition

Understanding Strong Knocking Mechanism Through High-Strength Optical Rapid Compression Machines

Influence of the Wall Temperatures of the Combustion Chamber and Intake Ports on the Charge Temperature and Knock Characteristics in a Spark-Ignited Engine

Flame Propagation and Auto-Ignition Behavior of Iso-Octane Across the Negative Temperature Coefficient (NTC) Region on a Rapid Compression Machine

Visualization Research on Low-Temperature Ignition and Combustion Characteristics of Diesel/Gasoline Blends Under Cold-Start Conditions

Experimental Study on Knocking Combustion in Compressionignition Engines under High-Altitude Conditions