Abstract:Numerous combustion strategies have been suggested for compression ignition engines in order to meet the stringent emission regulations with minimal sacrifice in the fuel economy. Premixed charge compression ignition combustion has the potential to reduce the nitrogen oxide emissions and the soot emissions while maintaining a high thermal efficiency and has become the research focus recently. Experiments and simulations were used to study the effects of the injection mode and the injection timing on the premixed charge compression ignition combustion and the emissions in a heavy-duty diesel engine at low and medium loads. The results reveal the following. At low loads, when the injection timing of a single injection is 35° crank angle before top dead centre because of the impinging position of the spray, the mixture is divided into two parts: the fuel above the chamber and the fuel in the piston bowl. This helps to utilize fully the in-cylinder air to form a homogeneous mixture. Also the nitrogen oxide emissions are the lowest. At medium loads, with a single injection, the injection mass is increased, the injection duration is prolonged and the mixing timing is reduced. As a result, the soot emissions, the carbon monoxide emissions and the unburned hydrocarbon emissions are increased dramatically; the best emissions are gained at an injection timing of 35° crank angle before top dead centre owing to the combined effect of the optimized mixing time and the optimized mixing space. At medium loads, with multiple injections, the injection mass is divided into four pulses, the mixing timings of which are all increased. The mixing space of the fuel–air mixture is also improved, and a more homogeneous mixture is obtained, which is beneficial to decreasing the soot emissions, the carbon monoxide emissions and the unburned hydrocarbon emissions in comparison with those for the single-injection case. When the injection timings of multiple injections are 80° crank angle before top dead centre, 65° crank angle before top dead centre, 50° crank angle before top dead centre and 35° crank angle before top dead centre, the best trade-off between the performance and the emissions can be achieved at medium loads.

Effect of Injection Timing on Knock Combustion and Pollutant Emission of Heavy-Duty Diesel Engines at Low Temperatures

Effect of Injection Pressure on the Impinging Spray and Ignition Characteristics of the Heavy-Duty Diesel Engine under Low-Temperature Conditions

Effect of Injection Pressure and Fuel Mass on Wall-Impinging Ignition and Combustion Characteristics of Heavy-Duty Diesel Engine at Low Temperatures

Numerical study on the effect of multiple injection strategies on ignition processes for low-temperature diesel spray

A Numerical Investigation of Injection Pressure Effects on Wall-Impinging Ignition at Low-Temperatures for Heavy-Duty Diesel Engine

Numerical Investigations of Injection Timing Effects on a GDI Engine Performance: Part B, In-Cylinder Emission Formation and Oxidation Process

Numerical Study on Injections Interaction and Ignition Improvement of Multiple Injections for Low-Temperature Diesel Spray

Effects of the Injection Parameters on the Premixed Charge Compression Ignition Combustion and the Emissions in A Heavy-Duty Diesel Engine

An Preliminary Experimental Investigation into the Smoke Emissions at Early Injection Timings in a Single-Cylinder Research Diesel Engine

An Experimental Investigation into the Soot Particle Emissions at Early Injection Timings in a Single-Cylinder Research Diesel Engine

Effect of Injection Timing on Low Temperature Combustion Fuelled by Diesel and a Blend of Diesel and Gasoline

Effects of injection timing on mixture formation, combustion, and emission characteristics in a n-butanol direct injection spark ignition engine

Cylinder-to-cylinder Variation of Knock and Effects of Mixture Formation on Knock Tendency for a Heavy-Duty Spark Ignition Methanol Engine

Study on Effect of Pilot Injection on Diesel Low Temperature Combustion

Effect of Retarded Injection Timing on Knock Resistance and Cycle to Cycle Variation in Gasoline Direct Injection Engine

Effects of Injection Timing and Fuel Pulse Width on Mixture Preparation and Hydrocarbon Emissions of the First Cranking Cycle under Different Initial Piston Positions

Study of Exhaust Gas Composition and Dilution Effects on Diesel Spray Ignition Characteristics

Effect and optimization of injection timing on the combustion and particle emission of a gasoline engine

The Influence of Fuel Injection Timing on Exhaust Emission From a Diesel Engine

Numerical Study on the Wall-Impinging Diesel Spray Soot Generation and Oxidation in the Cylinder under Cold-Start Conditions of a Diesel Engine

Effects of Injection Timing on Exhaust Particle Size and Nanostructure on A Diesel Engine at Different Loads