Abstract:The lithium-ion battery has the advantages of high energy density, long service life, and good safety performance, and is used as an ideal energy storage device. Cobalt-free lithium-rich manganese cathode materials have attracted much attention due to their high specific capacity and low cost. However, its poor cycling performance is not conducive to practical application. So far, researchers have mainly addressed this problem with surface coatings. In this study, spinel Li4Mn5O12 was successfully prepared by wet chemical method to modify the surface of Li1.2Ni0.2Mn0.6O2. The X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) test results showed that the crystal structure of the samples did not change significantly, but the cationic order was improved. The results of the scanning electron microscope (SEM), energy dispersive spectrometer (EDS), and transmission electron microscope (TEM) showed that an ultrathin spinel Li4Mn5O12 surface-modified layer with a thickness of about 10 nm was successfully constructed on the raw material surface. In addition, the lithium-ion diffusion coefficients (DLi+) of the raw materials and modified materials were calculated by electrochemical impedance spectroscopy (EIS) test and impedance fitting. The results indicated that the ultrathin Li4Mn5O12 surface modification shell can increase the lithium-ion diffusion rate of the material and improve the rate capability of the material. So, the results show that the surface modification layer of spinel Li4Mn5O12 can reduce the oxygen loss of the first cycle and improve the cationic order of the material. Therefore, the first coulombic efficiency of Li4Mn5O12/Li1.2Ni0.2Mn0.6O2 material at the current density of 12.5 mA×g-1 reaches 80.46%, and the capacity retention rate reaches 91.74% after 50 cycles, which is 3.36% and 21.23% higher than that of the raw materials, respectively. It showed better electrochemical reversibility and cyclic stability. This study provides a straightforward and convenient modification method for improving the stability of cobalt-free lithium-rich manganese cathode materials and has a favorable application prospect.

Stabilized Cobalt-Free Lithium-Rich Cathode Materials with an Artificial Lithium Fluoride Coating

Durable lithium-ion insertion/extraction and migration behavior of LiF-encapsulated cobalt-free lithium-rich manganese-based layered oxide cathode

A cation/anion co-doped Li1.12Na0.08Ni0.2Mn0.6O1.95F0.05 cathode for lithium ion batteries

In–situ Construction of LixFeyOz Coatings on Cobalt–free Lithium–rich Cathode Materials for Enhanced Structural Stability and Electrochemical Performance

Reinforcing the Stability of Cobalt-free Lithium-rich Layered Oxides via Li-poor Ni-rich Surface Transformation

Buliding Ultrathin Li4mn5o12 Shell for Enhancing the Stability of Cobalt-Free Lithium-Rich Manganese Cathode Materials

Suppressing capacity fading and voltage decay of Li-rich layered cathode material by a surface nano-protective layer of CoF2 for lithium-ion batteries

Anticorrosive nanosized LiF thin film coating for achieving long-cycling stability of LiCoO2 at high voltages

Improvement of stability and capacity of Co-free, Li-rich layered oxide Li1.2Ni0.2Mn0.6O2 cathode material through defect control

A Novel Strategy to Suppress Capacity and Voltage Fading of Li‐ and Mn‐Rich Layered Oxide Cathode Material for Lithium‐Ion Batteries

Thermodynamically Stable Dual‐Modified LiF&FeF3 layer Empowering Ni‐Rich Cathodes with Superior Cyclabilities

Fluorine Doping and Al2O3 Coating Co-modified Li[Li0.20Ni0.133Co0.133Mn0.534]O2 As High Performance Cathode Material for Lithium-Ion Batteries

Enhanced Cycling Stability of Lithium-Rich Cathode Materials Achieved by in-situ Formation of LiErO2 Coating

Improving the Electrochemical Performance of LiNi1/3Co1/3Mn1/3O2 Cathode Material by LiF Modification

Single–crystalline LiNi0.8Co0.1Mn0.1O2 Stabilized by F–doping–induced Superlattice for 4.8 V Lithium–ion Batteries

A well-matched MgNiO 2 surface heterointerface layer to enhance the cycling stability of cobalt-free Li-rich Mn-based cathode materials

Improved Electrochemical Performance of Co-Free Ni-Rich Cathode Material for Lithium-Ion Battery Through Multi-Element Composite Modification

Tuning Li2MnO3-Like Domain Size and Surface Structure Enables Highly Stabilized Li-Rich Layered Oxide Cathodes.

Enhanced Electrochemical Performance of Li1.2mn0.54ni0.13co0.13o2 Cathode with an Ionic Conductive Livo3 Coating Layer

Enhanced interfacial reaction interface stability of Ni-rich cathode materials by fabricating dual-modified layer coating for lithium-ion batteries

Enhanced structurally stable cathodes by surface and grain boundary tailoring of Ni-Rich material with molybdenum trioxide