Abstract:Abstract Nickel-based alloy coatings were widely used for the remanufacturing of dies and moulds by laser cladding, but the crack sensitivity would be increase due to the higher strength and hardness, which reduced the wear resistance of Ni-based alloys. In this paper, Ni-based coatings with the addition of a plastic phase (an austenitic stainless net) were prepared using laser cladding technology, and the CeO 2 was added in cladding layers. The cracking mechanism, microhardness, microstructure, phase composition, and wear properties were investigated. The relationship between thermal stress and the elastic and plastic fracture had been developed from the standpoint of fracture mechanics and thermal elastic fracture mechanics. The fracture criterion of the nickel-based coating was obtained, and the study has shown that the crack sensitivity could be reduced by decreasing the thermal expansion coefficient Δ α . Thus, a new method was proposed, which the stainless steel nets were prefabricated on the substrate. It was found that the number of cracks reduced significantly with the addition of stainless steel net. When the stainless steel net with 14 mesh was added in Ni-based coatings, the average microhardness of nickel composite coating was 565 HV 0.2 , which was 2.6 times higher than that of the 45 steel substrate. Although the rare earth oxide 4 wt.% CeO 2 and stainless steel net were added in the Ni-based coating reducing the microhardness (the average microhardness is 425 HV 0.2 ), the wear resistance of it improved substantially. The wear volume of Ni-based composite coating was 0.56×10 −5 mm 3 ·N −1 ·m −1 , which was 85.1% lower than that of 45 steel. The experiment results have shown that the Nickel-based composite coating is equipped with low crack sensitivity and high abrasive resistance with austenitic stainless net and the rare earth oxide 4 wt.% CeO 2 . This research offers an efficient solution to produce components with low crack susceptibility and high wear-resistance coatings fabricated by laser cladding.

An Investigation of the Surface Quality and Corrosion Resistance of Laser Remelted and Extreme High-Speed Laser Cladded Ni-based Alloy Coating

Effect of Laser Remelting on Corrosion and Wear Resistance of Fe82Cr16SiB Alloy Coatings Fabricated by Extreme High-Speed Laser Cladding

Improvement of Ni–Cr–Mo Coating Performance by Laser Cladding Combined Re-Melting

Effect of Microstructure on the Corrosion Resistance of Coatings by Extreme High Speed Laser Cladding

Enhanced Tribological Properties of LA43M Magnesium Alloy by Ni60 Coating Via Ultra-High-Speed Laser Cladding

Comparison of Microstructure and Corrosion Resistance of 431 Stainless Steel Coatings Prepared by Extreme High-Speed Laser Cladding and Conventional Laser Cladding

Investigation on the effect of laser remelting for laser cladding nickel based alloy

A review on coatings deposited by extreme high-speed laser cladding: processes, materials, and properties

Research on the laser melting coating process of an AlCoCrFeNi high‐entropy alloy

Effect of oxide film on corrosion behavior of NiTi coating prepared by extreme high-speed laser cladding

Effect of laser lower and remelting on the microstructure and tribological properties of GH3230 superalloy coating fabricated by laser melting deposition

Investigation On The Microstructure And Wear Behavior Of Laser-Cladded High Aluminum And Chromium Fe-B-C Coating

Correlating microstructural features with improved wear and corrosion resistance of laser surface remelted A356 alloy at different scanning speeds

Enhanced wear and corrosion resistances of AlCoCrFeNi high-entropy alloy coatings via high-speed laser cladding

Study of Cracking Mechanism and Wear Resistance in Laser Cladding Coating of Ni-based Alloy

Microstructural evolution and high-temperature oxidation of TiC/IN625 coatings fabricated by multi-layer extreme high-speed laser cladding

Microstructural Transformation and High-Temperature Aluminum Corrosion Properties of Co-Based Alloy Coating Prepared by Laser Cladding

Effect of surface morphology and microstructure on the hot corrosion behavior of TiC/IN625 coatings prepared by extreme high-speed laser cladding

Study on Microstructure and Properties of AlCoCrFeNi High-Entropy Alloys by Extreme High-Speed Laser Cladding

Study on the Effect of Laser Remelting Energy Density on the Microstructure and Wear Resistance of Fe-Based Alloy Coatings Fabricated by Laser Cladding

Laser Cladding Ni35A120Fe Intermetallic Coating for Resisting High-Temperature Oxidation and Hot Corrosion