Abstract:9310 carburized steel experiences significant wear and spalling problems when operating under high friction and heavy loads, which severely restricts its applications in the aviation industry. Therefore, it holds great significance to further enhance the surface mechanical properties of 9310 carburized steel through suitable surface strengthening technologies. The Electropulsing-Assisted Ultrasonic Surface Rolling Process (EP-USRP) has been successfully applied to carburized 9310 steel, yielding significant improvements in surface quality, hardness, friction and wear properties, and microstructure. Systematic investigations were conducted under varying EP-USRP parameters. Regarding the electric pulse parameters, it is observed that with the increase in output voltage, surface properties such as surface roughness and surface hardness tend to first optimize and then deteriorate. After applying EP-USRP with optimal parameters, the surface roughness of carburized 9310 steel was reduced to Ra 0.154 μm, a mere 5 % of its initial value. The surface hardness experienced a substantial increase, reaching 909.2 HV, representing a notable improvement of 29.9 % compared to the original sample, with a corresponding hardening depth of 1400 μm. Moreover, the wear amount of carburized 9310 steel witnessed a remarkable reduction to 11.8 % of its initial value, accompanied by a decrease in the coefficient of friction to 43.0 %. The enhancement of carburized 9310 steel through EP-USRP is attributed to two key mechanisms: deformation hardening induced by severe plastic deformation and microstructure strengthening resulting from strain-induced martensitic transformation. Among them, the severe plastic deformation mechanism is dominant, Through these mechanisms, the proportion of small-angle boundaries in carburized 9310 steel strengthened by EP-USRP increased. Additionally, the grain size of the surface layer decreased, and the content of retained austenite in the surface layer decreased, collectively contributing to significant improvements in surface properties, as well as friction and wear performance.

Microstructures and Fatigue Behaviors of 25crni2mov Steel under Electropulsing-Assisted Ultrasonic Surface Rolling

Microstructures and rolling contact fatigue behaviors of 17Cr2Ni2MoVNb steel under combined ultrasonic surface rolling and shot peening

Rolling contact fatigue behaviors of 25CrNi2MoV steel combined treated by discrete laser surface hardening and ultrasonic surface rolling

Surface Properties of Quenched GCrl5 Steel Enhanced by Electropulsing Ultrasonic Surface Rolling Process

Surface properties of quenched GCr15 steel enhanced by electropulsing ultrasonic surface rolling process

Surface integrity and rolling contact fatigue behavior of 18CrNiMo7-6 steel subjected to ultrasonic surface rolling process

Bending Fatigue Behaviour and Fatigue Endurance Limit Prediction of 20Cr2Ni4A Gear Steel after the Ultrasonic Surface Rolling Process

Experimental study on surface integrity and fatigue life of an ultra-high strength steel by the composite strengthening process of pre-torsion and ultrasonic rolling

Enhanced surface properties and contact fatigue performance of Cr4Mo4V bearing steel subjected to ultrasonic surface rolling processingVerbesserte Oberflacheneigenschaften und Kontaktermudungsleistung von einem ultraschall-oberflachengewalzten Cr4Mo4V-Lagerstahl

Effect of Electropulsing on Surface Mechanical Properties and Microstructure of Aisi 304 Stainless Steel During Ultrasonic Surface Rolling Process

Study on microstructure of 42CrMo steel by ultrasonic surface rolling process

Enhanced Fatigue Performance and Surface Mechanical Properties of AISI 304 Stainless Steel Induced by Electropulsing-Assisted Ultrasonic Surface Rolling Process

Effect of Electropulsing on Surface Mechanical Behavior and Microstructural Evolution of Inconel 718 During Ultrasonic Surface Rolling Process

Effect of Ultrasonic Surface Rolling on the Microstructure and Corrosion Properties of Gear Steel 20CrNiMo After Carburizing

Microstructure and mechanical properties of high entropy CrMnFeCoNi alloy processed by electopulsing-assisted ultrasonic surface rolling

Surface Modification and Its Effect on the Tensile and Fatigue Properties of 300M Steel Subjected to Ultrasonic Surface Rolling Process

Evolution of surface mechanical properties and microstructure of Ti-6Al-4V alloy induced by electropulsing-assisted ultrasonic surface rolling process

Fatigue behaviors of ultrasonic surface rolling processed AISI 1045: the role of residual stress and gradient microstructure

Further enhancement of surface mechanical properties of carburized 9310 steel by electropulsing-assisted ultrasonic surface rolling process

Surface Integrity and Wear Behavior of 300M Steel Subjected to Ultrasonic Surface Rolling Process

Study on Fretting Wear Properties of GCr15 Steel Via Ultrasonic Surface Rolling Process