Abstract:This work attempts to prepare ethylene-a-olefin copolymer with relatively narrow composition distribution by modification of TiCl4/MgCl2 type supported Ziegler-Natta catalyst. A TiCl4/ID/MgCl2 type catalyst, where ID is a diester, was treated at room temperature with 2,6-'Pr2C6H3-OH at phenol: Ti molar ratio of 1:1 and the modified catalyst was analyzed for contents of titanium and aryloxy group. It was found that about one third of the titanium atoms in the modified catalyst (M-cat) was connected with an aryloxy group, but its Ti content was decreased to 1.44 wt% from 2.36 wt% of the original catalyst (O-cat). Ethylene-1-hexene copolymerization was conducted in n-heptane with M-cat or O-cat as catalyst and triisobutyl aluminium or methylaluminoxane as cocatalyst. The M-cat showed similar activity as the O-cat in catalyzing the copolymerization, but presented a weaker comonomer activation effect than the latter. The 1-hexene content of copolymer synthesized by M-cat was lower than that of the product of O-cat at the same conditions, but had a markedly narrower composition distribution. Each copolymer sample was fractionated into two fractions by extraction with boiling n-heptane, and the soluble part contains much more 1-hexene units than the insoluble part. The ratio of I-hexene content in the soluble fraction to that of the insoluble fraction was higher than 18 in copolymer prepared with O-cat, but this ratio was reduced to 3.7 when M-cat was used as the catalyst. On the other hand, the soluble part of copolymer prepared with M-cat showed a more random sequence distribution than that of the O-cat. The distributions of active centers in both the M-cat and O-cat were studied by deconvolution of the polymer's molecular weight distribution curves with multiple Flory most-probable distribution function. Both catalysts showed a broad molecular weight distribution that can be ascribed to 5 similar to 6 types of active centers, but the introduction of aryloxy group in the catalyst caused marked changes in the active center distribution. Possible mechanism of the catalyst modification was proposed.

Engineering Ethylene/1-Hexene Copolymers from Ethylene Stock with a Model-Guided Catalyst Feeding Policy

Preparation Of Comb-Shaped Polyolefin Elastomers Having Ethylene/1-Octene Copolymer Backbone And Long Chain Polyethylene Branches Via A Tandem Metallocene Catalyst System

Model Development for Semicontinuous Production of Ethylene and Norbornene Copolymers Having Uniform Composition

High Temperature High Pressure Tandem Polymerization of Ethylene for Synthesis of Ethylene‐1‐Hexene Copolymers from Single Reactor with SNS‐Cr and CGC‐Ti Catalysts

Effect of Catalysts Supporting on Tandem Polymerization of Ethylene Stock in Synthesis of Ethylene-1-Hexene Copolymer

Synthesis of Ethylene/1‐octene Copolymers with Controlled Block Structures by Semibatch Living Copolymerization

Tandem Action of Sns-Cr and Cgc-Ti in Preparation of Ethylene-1-Hexene Copolymers from Ethylene Feedstock

Synthesis of Ultrahigh-Molecular-weight Ethylene-1-hexene Copolymers with High Hexene Content Via Living Polymerization with Fluorinated Bis(phenoxy-Imine) Titanium(iv).

Synthesis of Ethylene‐1‐hexene Copolymers from Ethylene Stock by Tandem Action of Bis(2‐dodecylsulfanyl‐ethyl) Amine‐crcl3 and Et(Ind)2ZrCl2

Macromol. Rapid Commun. 3/2015

Modeling and Kinetics of Tandem Polymerization of Ethylene Catalyzed by Bis(2-Dodecylsulfanyl-ethyl)amine-crcl3 and Et(Ind)2ZrCl2

Control of Diffusion/Barrier Effects of Polymer-Coated Particles and the Strengthening of Ethylene Polymerization Reactor

Preparation of ultrahigh molecular weight ethylene/1-octene block copolymers using ethylene pressure pulse feeding policies

Synthesis of Polyethylene with Bimodal Molecular Weight Distribution by Supported Iron‐based Catalyst

The Effect of Feeding Sequence on the Structure and Properties of the Ethylene/1-Octene Copolymer in the Semi-Continuous Polymerization Reaction System

Advanced Catalyst Technology for Broad/Bimodal Polyethylene, Achieved by Polymer-Coated Particles Supporting Hybrid Catalyst

Synthesis and Characterization of Copolymer of Ethylene and 1-Hexene by Carbon Bridge CpCN-CGC

Ethylene-1-Hexene Copolymerization with A 2,6-Diisopropylphenol Modified Supported Ziegler-Natta Catalyst

Copolymerization of Ethylene with 1‐hexene Promoted by Novel Multi‐chelated Non‐metallocene Complexes with Imine Bridged Imidazole Ligand

Ethylene/1-Hexene Copolymer with Broadened Molecular Mass Distribution Obtained by Catalysis of TiCl_4/XROH/MgCl_2/Et_3Al

Tuning the Short Chain Branch Distribution of Ethylene and 1-Hexene Copolymers by SiO2-supported Silyl Chromate Catalyst with Different Al-alkyl Co-Catalysts