Abstract:Ti–6Cr–5Mo–5V–4Al (Ti-6554) alloy has wide applications for large load-bearing components in the aerospace field. However, during the hot forming process of the alloy in the α+β phase region, there are a variety of interaction and restriction softening mechanisms and complex texture evolution behaviors, which jointly affect the microstructure and mechanical properties. This paper systematically studies the softening mechanism and texture evolution of Ti-6554 alloy in the α+β phase region using electron backscatter diffraction (EBSD), including dynamic phase transformation (DPT) and dynamic spheroidization of α phase and dynamic recrystallization (DRX) of β phase. Firstly, the effect of deformation parameters on the DPT is studied, and it is found that the volume fraction of α phase declines gradually with raising the strain rate, deformation temperature and deformation amount. The yield stress and the driving force for DPT increase with raising the strain rate and decreasing the deformation temperature. The equiaxed α phase will gradually transform into the lamellar α phase during the spheroidization process, accompanied by the wedging of the β phase. The combined effect of DPT and dynamic spheroidization leads to α grain refinement. Furthermore, the effect of deformation parameters on the DRX process of β phase is also investigated. The DRX degree only increases gradually with increasing the strain. Increasing the deformation temperature and decreasing the strain rate do not significantly increase the DRX volume fraction. Meantime, the DRX process of the β phase is heavily dependent on the α phase. The higher proportion of the α phase is capable of promoting continuous dynamic recrystallization (CDRX) process of β phase, while the lower proportion of the α phase will promote the transformation of CDRX into dynamic recrystallization (DDRX), but can not effectively increase the DRX degree of β phase. Further, the texture evolution shows that due to the combined effect of DPT and dynamic spheroidization, the effect of deformation parameters on the texture strength of α phase is very complicated. For the β phase, and fiber textures are easily formed during the deformation process.

Microtexture Evolution Effected by Mo Content in Α + Β Titanium Alloys

Microstructural evolution and grain refinement in an intermetallic titanium aluminide alloy with a high molybdenum content

Influence of Mo content on microstructure and mechanical properties of β-containing TiAl alloy

Effect of 2–6 At.% Mo Addition on Microstructural Evolution of Ti-44Al Alloy

Hot Deformation Behavior of a Novel Near-β Titanium Alloy Ti-5.5Mo-6V-7Cr-4Al-2Sn-1Fe in (α+β) Phase Region

A Comparative Study on Microstructure and Mechanical Properties of Ti-43/46Al-5Nb-0.1B Alloys Modified by Mo

Effect of Mo Addition on Microstructures and Mechanical Properties of Ti2AlNb Alloy

Effects of Mo addition on the microstructure and mechanical properties of Ti45Al5Nb0.3Y alloy

Effect of Solution Treatment on Microstructure, Texture, and Anisotropy of Mechanical Properties in TA10 (Ti-0.3Mo-0.8Ni) Sheet

Textures of Rectangular Extrusions and Their Effects on the Mechanical Properties of Thermo-Mechanically Treated, Lamellar Microstructure, Ti–47Al–2Cr–2Nb–0.15B

Microstructural Evolution of a Ti-4.5Al-3Mo-1V Alloy During Hot Working

Microstructure and Texture Evolution of Ti65 Alloy during Thermomechanical Processing

Systematic analysis of the softening mechanism and texture evolution of Ti–6Cr–5Mo–5V–4Al alloy during hot compression in α+β phase region

Effects of Mo Addition on Microstructure and Mechanical Properties of Powder Metallurgical Ti-6Al-4V-2Cr Alloy

Effect of Deformation Temperature on the Microstructure and Texture Evolution of Ti-6Al-4Zr-2Mo-6V Alloy

The Effect of Precursory Α and Ω Phase on Microstructure Evolution and Tensile Properties of Metastable Β Titanium Alloy

Effect of cooling rate on α variant selection and microstructure evolution in a near β Ti–5Al–3Mo–3V–2Cr–2Zr–1Nb–1Fe alloy

Microstructure evolution, mechanical properties and high temperature deformation of (TiB + TiC)/Ti-3.5Al-5Mo-6V-3Cr-2Sn-0.5Fe titanium alloy

The evolution of primary alpha phase and its effect on microtexture in Ti6242S during post-deformation heat treatment

Microstructure and Texture Characterstics of a Near-Alpha Titanium Alloy Tube

α phase growth and branching in titanium alloys