Abstract:Ti–6Cr–5Mo–5V–4Al (Ti-6554) alloy has wide applications for large load-bearing components in the aerospace field. However, during the hot forming process of the alloy in the α+β phase region, there are a variety of interaction and restriction softening mechanisms and complex texture evolution behaviors, which jointly affect the microstructure and mechanical properties. This paper systematically studies the softening mechanism and texture evolution of Ti-6554 alloy in the α+β phase region using electron backscatter diffraction (EBSD), including dynamic phase transformation (DPT) and dynamic spheroidization of α phase and dynamic recrystallization (DRX) of β phase. Firstly, the effect of deformation parameters on the DPT is studied, and it is found that the volume fraction of α phase declines gradually with raising the strain rate, deformation temperature and deformation amount. The yield stress and the driving force for DPT increase with raising the strain rate and decreasing the deformation temperature. The equiaxed α phase will gradually transform into the lamellar α phase during the spheroidization process, accompanied by the wedging of the β phase. The combined effect of DPT and dynamic spheroidization leads to α grain refinement. Furthermore, the effect of deformation parameters on the DRX process of β phase is also investigated. The DRX degree only increases gradually with increasing the strain. Increasing the deformation temperature and decreasing the strain rate do not significantly increase the DRX volume fraction. Meantime, the DRX process of the β phase is heavily dependent on the α phase. The higher proportion of the α phase is capable of promoting continuous dynamic recrystallization (CDRX) process of β phase, while the lower proportion of the α phase will promote the transformation of CDRX into dynamic recrystallization (DDRX), but can not effectively increase the DRX degree of β phase. Further, the texture evolution shows that due to the combined effect of DPT and dynamic spheroidization, the effect of deformation parameters on the texture strength of α phase is very complicated. For the β phase, and fiber textures are easily formed during the deformation process.

Microstructure and Texture Evolution of Ti65 Alloy during Thermomechanical Processing

Hot Deformation Behavior of a Novel Near-β Titanium Alloy Ti-5.5Mo-6V-7Cr-4Al-2Sn-1Fe in (α+β) Phase Region

Systematic analysis of the softening mechanism and texture evolution of Ti–6Cr–5Mo–5V–4Al alloy during hot compression in α+β phase region

Microstructure and Texture Variations in High Temperature Titanium Alloy Ti65 Sheets with Different Rolling Modes and Heat Treatments

Textures of Rectangular Extrusions and Their Effects on the Mechanical Properties of Thermo-Mechanically Treated, Lamellar Microstructure, Ti–47Al–2Cr–2Nb–0.15B

Study on the Relationship Between Microstructure and Mechanical Property in a Metastable Β Titanium Alloy

Tailoring microstructure and mechanical performance of a β-solidifying TiAl alloy via martensitic transformation

Effect of thermomechanical processing on evolution of various phases in Ti–Nb–Zr alloys

Texture evolution during multi-pass cold rolling and annealing of Ti-2Al-1.5Mn alloy

Microstructure Evolution of TB18 Alloy after Thermal Treatment and the Effect of Recrystallization Texture on Mechanical Properties

Texture Evolution of α‐Ti and β‐Ti Alloys During Rolling and Recrystallization

The Microstructure and Texture Evolution of Large-Sized Metastable β-Titanium Alloy Bar during Forging Processes

Microstructural Evolution and Mechanical Properties of Ti-22Al-25Nb (at.%) Orthorhombic Alloy with Three Typical Microstructures

The evolution of primary alpha phase and its effect on microtexture in Ti6242S during post-deformation heat treatment

Microtexture Evolution Effected by Mo Content in Α + Β Titanium Alloys

The Effect of Precursory Α and Ω Phase on Microstructure Evolution and Tensile Properties of Metastable Β Titanium Alloy

Effect of Solution Treatment on Microstructure, Texture, and Anisotropy of Mechanical Properties in TA10 (Ti-0.3Mo-0.8Ni) Sheet

Study on High-Temperature Flow Behavior and Substructure and Texture Evolution of TA15 Titanium Alloy

Evolution of microstructure and texture of a near α titanium alloy during forging bar into disk

Quantitative analysis on microstructure characteristic of pre-strained β-solidified TiAl alloy during post-heat treatment

Static Recrystallization Behavior and Texture Evolution during Annealing in a Cold Rolling Beta Titanium Alloy Sheet