Abstract:<p>The size, distribution and chemical composition of grain boundary η-phase precipitates (GBPs) and micro-segregation present in thick plate (140 mm) 7xxx Al alloys has been quantified across a range of length scales. To address the known limitations of individual characterisation methods, a number of cross-correlated, high resolution techniques have been used, including atom probe tomography (APT). A new-generation high-Zn alloy (AA7085) has been compared to a more established material, AA7050, in T7651 temper conditions. The results show that high angle grain boundaries in both alloys are dominated by quench-induced GBPs (Q-GBPs), covering up to ∼40% of the area in AA7050. When viewed on brittle intergranular fracture surfaces and in 3D, the Q-GBPs appear much larger than previously reported and exhibit complex branched-facetted morphologies. In AA7050, the Q-GBPs contain substantially higher levels of Cu (by 29 %) and Al (by 37%) and lower Zn (by 33 %) than AA7085. Classical modelling demonstrates that these differences result from different transformation pathways, with precipitates in the more quench sensitive AA7050 alloy nucleating at higher temperatures, which exaggerates the effect of alloy chemistry. In both alloys GB segregation was limited, with low levels of Zn detected relative to the matrix, but more Mg and less Cu in AA7050. It is, therefore, proposed that the higher Cu and Al, and lower Zn content, of the large Q-GBPs present in AA7050 is the main difference in GB microchemistry between the two materials and is the primary reason its GBs are less chemically active. The implications for the relative susceptibilities of the alloys to environmentally assisted cracking are briefly discussed.</p>

Stress Corrosion Cracking Resistant Nanostructured Al-Mg Alloy with Low Angle Grain Boundaries

Improve Sensitization and Corrosion Resistance of an Al-Mg Alloy by Optimization of Grain Boundaries

Enhancing Stress Corrosion Cracking Resistance of Low Cu-Containing Al-Zn-Mg-Cu Alloys by Aging Treatment Control

Thermally Stable and Corrosion Resistant Nanolaminated Al-Mn Alloy with Low Angle Boundary Structures

Disclosing Differential Precipitation Behavior of a Novel High Mg-containing Al-Mg-Zn-Si Alloy

Realizing ultra-fine grains and ultra-high strength in conventionally extruded Mg-Ca-Al-Zn-Mn alloys: The multiple roles of nano-precipitations

Enhancing Plasticity in BCC Mg-Li-Al Alloys Through Controlled Precipitation at Grain Boundaries

Nano‐Dual‐Phase Metallic Glass Film Enhances Strength and Ductility of a Gradient Nanograined Magnesium Alloy

Engineering Atomic-to-Nano Scale Structural Homogeneity towards High Corrosion Resistance of Amorphous Magnesium-Based Alloys

Approaching 1 GPa ultra‐high tensile strength in a nanostructured Al‐Zn‐Mg‐Cu‐Zr‐Sc alloy prepared by severe plastic deformation

Multiscale analysis of grain boundary microstructure in high strength 7xxx Al alloys

Enhancing the strength and sensitization resistance of 5xxx alloys via nanoscale clustering induced by room-temperature cyclic plasticity

High corrosion resistance and weak corrosion anisotropy of an as-rolled Mg-3Al-1Zn (in wt.%) alloy with strong crystallographic texture

Nanoscale coherent interface strengthening of Mg alloys

Deformation and Fracture Mechanisms of an Annealing-Tailored "bimodal" Grain-Structured Mg Alloy

Atomic-scale inhomogeneous solute distribution in an ultrahigh strength nanocrystalline Al-8 Mg aluminum alloy

Corrosion behavior and mechanical properties of extruded low-alloyed Mg−0.5Bi−0.5Y−0.2Zn alloy

Tailoring the heterophase interfacial structures to improve both strength and ductility of Al-Li alloys by fine tuning major solute Mg

Strong and thermally stable nanocrystalline Cu–Al alloy via Al segregation

Grain Refinement Enhanced Tensile Strength, Fracture Toughness and Fatigue Crack Propagation Resistance of a High Zn-Containing Al-Zn-Mg-Cu Alloy

Effect of a bimodal grain structure on corrosion behavior and tensile properties of low-alloyed Mg-1Bi-1Zn-1Ag alloy