Abstract:Journal of Reinforced Plastics and Composites, Ahead of Print. Polymer-based composites (GFRP) are increasingly used in the mechanical industry due to their cost-profitability, durability, and good mechanical properties. In the present study, a metal carbide tool was employed to manufacture polyamide (PA66-GF30%) specimen in a dry environment. The impact of variations in cutting process parameters on the responses studied is investigated using two experimental techniques. The first is the OFAT approach. For the second technique (multifactorial), the effects of input parameters on technological parameters (Ra, Fz, MRR, and Pc) are quantified aided by the ANOVA method using an experimental design based on Taguchi's L9 (3 × 3) orthogonal matrix. Based on the RSM methodology, the results were processed statistically to propose prediction models for the different outputs. In addition, a single-objective optimization study of Taguchi's and a multi-objective optimization of the operating conditions using the classification method based on CoCoSo as well as the DF Approach according to two desired objectives were carried out. The first objective of this study concerns the minimization of (Ra, Fz, and Pc), and the second one considers the minimization of (Ra, Fz, and Pc) at the same time as maximizing (MRR). Finally, the surface roughness criteria (Ra and Sa) of PA66-GF30% were evaluated to study the effect of the feed (f) on the machined surface topography. The findings are of capital importance in that they provide the required and correct information about the working conditions of composite polymers. According to "OFAT" results, feed (f) is the predominant factor influencing roughness (Ra). Temperature in the cutting zone rises with increasing cutting conditions (Vc, f and ap). Variations in cutting conditions affect the morphology of the chip produced. The roughness criteria (Ra and Sa) results clearly show that the topography of the PA66-GF30% surface changes as (f) changes. Also, optimization of all performance parameters simultaneously indicates that the DFA offers the best combination of parameters: Vc = 187.50 m × min−1, f = 0.096 mm × rev−1, and ap = 0.866 mm, leading to the minimization of (Ra) and maximization of (MRR), with respective values of 1.24 μm and 15.614 cm3 × min−1. Furthermore, the CoCoSo method favors the minimization of (Fz and Pc) with values of 20.18 N and 69.285 W, respectively.

Optimization of Process-Induced Residual Stresses in Automated Manufacturing of Thermoset Composites

A Review on the Mechanical Modeling of Composite Manufacturing Processes

Collaborative multi‐scale optimization of molding processes for thermosetting/quartz fiber composites based on balancing between efficiencies and mechanical properties

Design Optimization of Molds for Autoclave Process of Composite Manufacturing

Design and Optimization of Manufacturing Process of Polymer Composites Through Multiscale Cure Analysis and NSGA-II

Experimental and statistical study on the effect of process parameters on the quality of continuous fiber composites made via additive manufacturing

Optimization of Cure Profile for Thick Composite Parts Based on Finite Element Analysis and Genetic Algorithm

A Heat-Balance Method for Autoclave Process of Composite Manufacturing

Stress-Aware Optimal Placement of Actuators for High Precision Quality Management in Composite Aircraft Assembly

Optimization of the Compression (Injection/Compression) Molding Process Using Numerical Simulation

Coupling of injection molding process to mechanical properties of short fiber composites: A through process modeling approach

Optimization of the cycle time in resin transfer molding process by numerical simulation

Theoretical and Experimental Studies on Residual Stresses of Advanced Polymer Composites

Optimal Polymerization Conditions in Thermoplastic-Resin Transfer Molding Process for Mechanical Properties of Carbon Fiber-Reinforced PA6 Composites Using the Response Surface Method

A Manufacturing Process Simulation of Toughened Cyanate-Ester-Based Composite Structures with Respect to Stress Relaxation

Optimize Additive Manufacturing Post-Build Heat Treatment and Hot Iso-Static Pressing Process Using an Integrated Computational Materials Engineering Framework

Optimization of Compression Molding Process Parameters for NFPC Manufacturing Using Taguchi Design of Experiment and Moldflow Analysis

Optimization of Fused Deposition Modeling Process Parameters and Dynamic Mechanical Analysis of 3D Printed Polycarbonate/Acrylonitrile-Butadiene-Styrene Composite Loaded with Tetrabromobiphenol-A and Microcrystalline Cellulose

Research Progress in Numerical Simulation of Fiber Reinforced Thermosetting Resin Matrix Composites Molding Process

Investigation on machining of GFRP through ANOVA, DFA, and CoCoSo method combined with Taguchi approach

Parametric process optimisation of automated fibre placement (AFP) based AS4/APC-2 composites for mode I and mode II fracture toughness