Abstract:GEN3 steels are a new family of automotive sheet steels developed and commercialized in the last three years, specifically for body-in-white applications. The high ductility in GEN3 steels is typically achieved through the transformation-induced plasticity (TRIP) effect by the addition of silicon or aluminum. When these steels are formed into parts, the TRIP effect of austenite to martensite transformation provides enhanced ductility. Typically, 10 to 12 micrometers of zinc coating (known as galvanized coating) is applied to automotive steel sheets for corrosion protection. Liquid metal embrittlement (LME) cracking can occur during resistance spot welding (RSW) of galvanized steels. LME cracking occurs when molten zinc penetrates prior austenite grain boundaries of the steel substrate. The precise role of silicon in the LME cracking behavior in TRIP and GEN3 steels is unknown. Therefore, a study was undertaken to examine the role of silicon in LME cracking behavior of GEN3 steels. The purpose was also to examine if the presence of retained austenite is required for LME cracking to occur. In this study, laboratory heats were prepared using three silicon levels. Samples cut from galvanized panels were welded using a resistance spot welding machine, and weld areas were examined metallographically for the presence of LME cracks. Gleeble® simulations were done to study the LME behavior of the three steels prepared. Base materials were examined with a scanning electron microscope using the electron back-scattered diffraction (EBSD) method to examine the nature of grain boundaries found. The effect of retained austenite in LME cracking was studied using the Gleeble®. Both RSW and Gleeble® results showed silicon promotes LME cracking in steels, predominantly in the weld heat-affected zones(HAZs). More low-energy, low-coincidence site lattice (CSL) boundaries were found as the silicon content of the steel was decreased. These boundaries do not host cracks. Higher silicon appeared to shrink the safe temperature range over which LME cracks could be avoided, thus indicating heat in-put control to limit cracks has limited windows as the silicon in steel goes up. It was shown that the presence of retained austenite in steel is not a prerequisite for LME cracking to occur.

The Influence of Pre-Plating on the LME Phenomenon of Advanced High Strength Steel

Uncovering the mechanism of the LME susceptibility for the galvanized and electrogalvanized DP 1180 steels

Zn-induced Liquid Metal Embrittlement and Mechanical Properties of Advanced High-Strength Steel with Resistance Spot Weld

The Influence of Precooling on Liquid Metal Embrittlement and Microstructure Properties of Galvanized 22mnb5 Tubes

Investigation of the LME Susceptibility of Dual Phase Steel with Different Zinc Coatings

Effect of Ni-interlayer on zinc-assisted liquid-metal-induced-embrittlement susceptibility of 22MnB5 galvanized steel

Towards an Explanation of Liquid Metal Embrittlement Cracking in Resistance Spot Welding of Dissimilar Steels

Comparative Study on the Liquid Metal Embrittlement Susceptibility of the High-Si Advanced High-Strength Steel with EG and GA Zn Coatings

Effect of Alloying Elements on Zinc-Induced Liquid Metal Embrittlement in Steels: A First-Principles Study

Liquid Metal Embrittlement Cracking During Resistance Spot Welding of Galvanized Q&P980 Steel

Interactions of Nanoprecipitates, Metastable Austenite, and Lüders Banding in an Ultra-Low Carbon Medium Mn Steel with Abnormal Strength Dependence of Hydrogen Embrittlement

Liquid Metal Embrittlement Of Galvanized Steel And Its Performance During Resistance Spot Welding

Experimental Investigation of Hot Forming of Zn‐Coated Hot‐Stamping Steel

A Study on the Weldability of Automotive Galvanized Steel Sheet in Resistance Spot Welding

Formation mechanism of liquid metal embrittlement in laser lap welding of zinc-coated GEN3 steels

Effect of the Interface Microstructure of Hot-Dip Galvanizing High-Strength Automobile Steel on Its Tensile Fracture Behaviors

The High-Cycle Tensile-Shear Fatigue Properties and Failure Mechanism of Resistance Spot-Welded Advanced High-Strength Steel with a Zn Coating

Hydrogen embrittlement of a cold-rolled Al-containing medium-Mn steel: Effect of pre-strain

Critical LME elongation: a criterion measured with Gleeble correlated to LME sensitivity during spot welding

The effect of Zn coating layer on the microstructure and mechanical properties of friction stir spot welded galvanized DP590 high-strength steel plates

Effect of Silicon and Retained Austenite on the Liquid Metal Embrittlement Cracking Behavior of GEN3 and High-Strength Automotive Steels