Abstract:Good gas permeability is an essential factor for the smooth operation and high performance in the lower part of the blast furnace. Under the present low carbon blast furnace smelting conditions, the coke layer is thinner, and the proportion of the molten metal in the coke layer is significantly higher, resulting in a major reduction in gas permeability, which seriously affects blast furnace operations. Also, the lower thickness of the coke layer weakens the process of solid-liquid carbon dissolution when the molten iron passes through the coke layer, which reduces the carbon content of the molten iron and further deepens the erosion of the refractory by the unsaturated molten iron. The carbon dissolution in the molten iron in a blast furnace core was measured by a high-temperature vacuum wettability test tool that analyzed the interface wetting activity between Fe−C melts with specific carbon mass fraction (3.8%, 4.3%, 4.8%) and 99.9% of high temperatures graphite plates. Besides, the scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) were used to analyze the graphite substrate’s carburizing morphology and carburizing distances. The results show that, with the increase of carbon content, the interface contact angle becomes bigger. The contact angle decreases with time, and eventually reaches a steady-state during the melting process, and the Fe−C melt with saturated carbon cannot be wet. The scanning electron microscopy analysis shows that a spherical cap-like depression is created by a cross-section of the Fe−C melt and the graphite substrate, and the radius and volume of the depression decrease with increasing carbon content. The study of the EDS scanning analysis shows that the amount of dissolved carbon atoms in the graphite substrate penetrates the Fe−C melt and decreases with increasing initial carbon concentration. The smaller the carburizing effect, the better the wetting is conducive to carbon mass transfer. It is found that by measuring carburizing of the carbon atoms in the graphite substrate into the Fe−C melt by calculating the surface energy reduces the surface energy between the two. Thus, the surface tension decreases and the melt spreads slowly with contact angle gradually decreasing during melting.

Kinetics of carbon oxidation reaction between molten iron of high carbon concentration and iron oxide containing slag.

Oxidation Reaction of Silicon in Molten Iron of High Carbon Concentration by FeO Containing Slag

Dissolution of Carbon-Containing Species in CaO-SiO 2 -Al 2 O 3 Slag

Oxidation Kinetics and Mechanism of TiC with Simulated Blast‐Furnace Gases

Interface Wetting Behavior Between Iron and Coke During the Carbon Dissolution Process in a Blast Furnace

Study on Oxidation Kinetics and Mechanism of Copper Slag Under Non-isothermal Conditions

Dissolution Mechanism of Modifying Agent in Fibrotic Process of Steel Slag

Kinetics analysis of iron oxide reduction by solid carbon in HIsmelt ironmaking slag

Effect of Al2O3 on the Molten Slag Microstructure Information by Molecular Dynamics Simulation and Experimental Analysis

Investigation of Selective Oxidation During Cooling of Hot-Rolled Iron-Manganese-silicon Alloys

Dissolution Kinetics of SiO2 into CaO-Fe2O3-SiO2 Slag

Development of a kinetic model for Ti‐bearing steel‐slag reaction

Interfacial Phenomenon and Marangoni Convection of Fe–C Melt on Coke Substrate under in Situ Observation

Effect of Iron Oxide Dissolution on Thermochemical Property of Solid Solution between Ca 2 SiO 4 and Ca 3 P 2 O 8 at 1573 K

Effect of CaO/SiO2 and P2O5 on the Viscosity of FeO-SiO2-V2O3-CaO-P2O5 Slags

Effects of CaO, Al2O3 and MgO on Kinetics of Lead-Rich Slag Reduction

Simulation research on oxygen mass transfer between steel and slag in IF steel refining process

Thermodynamic Analysis of Mineral Phase Composition of Steel Slag System

Effect of Coordination Structure of Iron Ions on Iron Oxide Activity Coefficients in the CaO‐SiO2‐FeO‐Fe2O3 Slags at 1573 K Under Oxygen Partial Pressures Between 10−9 and 10−4 atm

The Effect of SiC on the Phase Composition and Structure of Mixed Slag

Slurry-Phase Carbonation Reaction Characteristics of AOD Stainless Steel Slag