Porous In2O3:RE (RE = Gd, Tb, Dy, Ho, Er, Tm, Yb) Nanotubes: Electrospinning Preparation and Room Gas-Sensing Properties

Lin Xu,Biao Dong,Yu Wang,Xue Bai,Jiansheng Chen,Qiong Liu,Hongwei Song

DOI: https://doi.org/10.1021/jp101115v

2010-01-01

Abstract:In2O3:RE (RE = Gd, Tb, Dy, Ho, Er, Tm, Yb) as well as In2O3 nanotubes (NTs) with a diameter of ∼85 nm and wall thickness of ∼15 nm were systematically fabricated by the electrospinning method for t...

What problem does this paper attempt to address?

Porous In2O3:RE (RE = Gd, Tb, Dy, Ho, Er, Tm, Yb) Nanotubes: Electrospinning Preparation and Room Gas-Sensing Properties

x w lin,Biao Dong,y g wang,xue song bai,Jiansheng Chen,qiong z liu,Hongwei Song

DOI: https://doi.org/10.1021/jp101115v

2010-01-01

Abstract:In2O3:RE (RE = Gd, Tb, Dy, Ho, Er, Tm, Yb) as well as In2O3 nanotubes (NTs) with a diameter of similar to 85 nm and wall thickness of similar to 15 nm were systematically fabricated by the electrospinning method for the first time and characterized by various techniques. The results demonstrate that, except for In2O3:Tb, which contained a mixed phase (cubic and rhombohedral), the lattice constants of cubic In2O3:RE gradually decreased and the band-gap energies and the resistances in air gradually increased with the increase of doped RE atom order. As a consequence, it is exciting to observe that the doping of RE gradually and significantly improved the gas-sensing properties of In2O3 NTs to H2S gas as the RE varied from Gd to Yb in order. In contrast to undoped In2O3 NTs, the room-temperature response sensitivity of the In2O3:Yb NT sensors to 20 ppm H2S increased about 7 times and reached as high as 1241, whereas the response time of the In2O3:Yb NT sensors was shortened 4 times and reached similar to 49 s. The present electrospun In2O3:RE NTs are highly promising H2S gas sensors that can work under soft conditions.
Synthesis and Photoluminescence of Y2O3:RE3+ (re=eu, Tb, Dy) Porous Nanotubes Templated by Carbon Nanotubes.

Guixia Liu,Guangyan Hong

DOI: https://doi.org/10.1166/jnn.2006.17915

2006-01-01

Journal of Nanoscience and Nanotechnology

Abstract:Y2O3:RE3+ (RE = Eu, Tb, Dy) porous nanotubes were first synthesized using carbon nanotubes as template. The morphology of the coated precursors and porous Y2O3:Eu3+ nanotubes was determined by scanning electron Microscopy (SEM) and transmission electron microscopy (TEM). It was found that the coating of precursors on carbon nanotubes (CNTs) is continuous and the thickness is about 15 nm, after calcinated, the Y2O3:Eu3+ nanotubes are porous with the diameter size in the range of 50–80 nm and the length in micrometer scale. X-ray diffraction (XRD) patterns confirmed that the samples are cubic phase Y2O3 and the photoluminescence studies showed that the porous rare earth ions doped nanotubes possess characteristic emission of Eu3+, Tb3+, and Dy3+. This method may also provide a novel approach to produce other inorganic porous nanotubes used in catalyst and sensors.
In(OH)3particles from an Ionic Liquid Precursor and Their Conversion to Porous In2O3particles for Enhanced Gas Sensing Properties

Zhonghao Li,Yang Li,Yuxia Luan,Junchao Li,Aixin Song

DOI: https://doi.org/10.1039/c2ce26733k

IF: 3.756

2013-01-01

CrystEngComm

Abstract:The ionic liquid precursor tetrabutylammonium hydroxide (TBAH) is used to synthesize In(OH)3 particles. The ionic liquid TBAH is demonstrated to be effective for the synthesis of In(OH)3 nanorods with a controlled size. The effect of the indium salt and the added water amount on the final products is investigated. The synthesized In(OH)3 nanorods could be further transformed into porous In2O3 rod particles. Specifically, the gas sensing properties of the synthesized porous In2O3 rod particles to various organic compounds (methanol, ethanol, isopropanol, butanol, ethyl acetate and toluene) exhibit remarkable sensitivities, low detection limits and fast response–recovery times, which are superior to the reported In2O3 based sensors. The as-prepared porous In2O3 rod-based sensors thus demonstrate their potential applications in detecting chemical contaminants and dangerous gases.
High-performance acetone sensor based on electrospun Tb-doped a-Fe2O3 nanotubes

Long Chen,Yanhua Song,Qiwen Yu,Hao Dong,Chenying Pan,Di Wang,Jun Liu,Xing Chen

DOI: https://doi.org/10.1016/j.ceramint.2022.05.384

IF: 5.532

2022-01-01

Ceramics International

Abstract:Gas sensing requires precise gas detection, hence the need for the development of semiconductors with highly selective and sensitive properties. Herein, different amounts of Tb-doped Fe2O3 nanotubes (NTs) are successfully fabricated for detecting acetone gas using electrospinning followed by calcination at 550 ?. Specifically, the gas sensing investigation indicated that 5% Tb-Fe2O3 NTs to 50 ppm acetone reached 53.2 at 170 ?, which is 13 times higher than that of pure Fe2O3 NTs. In addition, the sensor also displays good selectivity and a low detection limit (200 ppb) for acetone. The significant increase in acetone sensing performance could be ascribed to hollow structures with a high specific surface area and the increase in oxygen vacancies by Tb doping. The proposed Tb-doped Fe2O3 NTs offer an effective strategy for fabricating a highly sensitive acetone sensor, which can work well at a relatively low temperature.
Synthesis and photoluminescence of Y 2O 3:RE 3+(RE = Eu, Tb, Dy) porous nanotubes templated by carbon nanotubes

Guixia Liu,Guangyan Hong

DOI: https://doi.org/10.1166/jnn.2006.030

2006-01-01

Journal of Nanoscience and Nanotechnology

Abstract:MWNTs (multi-walled carbon nanotubes) were made by catalytic CVD process using iron-containing mesoporous silica, Fe-MCM-41, with 4 mol% Fe loading prepared by direct synthesis route. Uniform 5 nm size Fe2O3 nano-particles impregnated onto a mesoporous silica support, SBA-15 were also prepared for CNTs synthesis. The catalysts were characterized using XRD, SEM/TEM, N-2 physisorption, UV-vis diffuse reflectance and FT-IR spectroscopies. Acetylene gas was introduced as a carbon source, and the gas mixture of Ar:H-2:C2H2 = 14:5:1 pyrolyzed at 750 degrees C for 60 min was found to be the optimum synthesis condition. Fe-MCM-41 due to higher dispersion of nano-sized Fe-species was efficient as catalyst for MWNTs with more uniform size distribution. Cobalt-impregnated Fe-MCM-41 (Co/Fe = 1) produced a small fraction of SWNTs of ca. 2 nm diameter mixed with MWNTs.
The fabrication of In2O3 nanowire and nanotube by single nozzle electrospinning and their gas sensing property

Lili Liu,Shouchun Li,Xin Guo,Lianyuan Wang,Li Liu,Xuesong Wang

DOI: https://doi.org/10.1007/s10854-016-4407-7

2016-02-25

Abstract:It has been reported a lot that nanowire and nanotube semiconductor oxide type sensor possess excellent sensing property. Many works ascribed excellent sensing properties to the big specific surface area. Herein, In2O3 nanofiber and nanotube were synthesized by single nozzle electrospinning and followed by calcination with different heating rate. And the samples were characterized by scanning electron microscopy, and powder X-ray diffraction. Their gas sensing properties were studied to investigate the advantages of their morphologies, and the response and recovery dynamic curves were also tested to investigate their gas sensitive characteristics. The results show that acetone sensing sensitivity based on nanotubes is better than that of nanowires.

engineering, electrical & electronic,materials science, multidisciplinary,physics, condensed matter, applied
NiO@ZnO Heterostructured Nanotubes: Coelectrospinning Fabrication, Characterization, and Highly Enhanced Gas Sensing Properties.

Lin Xu,Ruifang Zheng,Shuhai Liu,Jian Song,Jiansheng Chen,Biao Dong,Hongwei Song

DOI: https://doi.org/10.1021/ic300749a

IF: 4.6

2012-01-01

Inorganic Chemistry

Abstract:Novel NiO@ZnO heterostructured nanotubes (NTs) were fabricated by the coelectrospinning method, consisting of external hexagonal ZnO shell and internal cubic NiO NTs. They are carefully investigated by scanning electron microscopy, transmission electron microscopy, scanning transmission electron microscopy, energy-dispersive X-ray spectroscopy mapping, X-ray diffraction, and X-ray photoelectron spectroscopy techniques. A reasonable formation mechanism of the hierarchical NiO@ZnO NTs is proposed, which is discussed from the view of degradation temperature of different polymers and the amount of inorganic salts. They were then explored for fabrication of H(2)S gas sensors. The gas sensing test reveals that compared with the pure ZnO, NiO, and the ZnO-NiO mixed gas sensors, hierarchical gas sensor exhibits highly improved sensing performances to dilute hydrogen sulfide (H(2)S) gas. The response of the optimum NiO@ZnO NTs sensor to 50 ppm H(2)S increases as high as 2.7-23.7 times compared to the other sensors, whereas the response and recovery times also become shorter considerably. These enhanced gas sensing properties are closely related to the change of nanostructure and activity of ZnO and NiO nanocrystals as well as combination of homo- and heterointerfaces in the optimum gas sensor, which are confirmed by a series of well-designed experiments.
Porous Indium Oxide Nanotubes: Layer-by-Layer Assembly on Carbon-Nanotube Templates and Application for Room-Temperature NH3 Gas Sensors

N. Du,H. Zhang,B. D. Chen,X. Y. Ma,Z. H. Liu,J. B. Wu,D. R. Yang

DOI: https://doi.org/10.1002/adma.200602128

IF: 29.4

2007-01-01

Advanced Materials

Abstract:Porous and polycrystalline In2O3 nanotubes are prepared by layer-by-layer assembly on CNT templates and subsequent calcination (see figure). The as-prepared In2O3 nanotubes exhibit superior sensitivity to NH3 at room temperature, as well as a good reproducibility and short re sponse/recovery time. This novel approach presented herein can be extended to synthesize other metal oxide nanotubes such as NiO, SnO2, Fe2O3, and CuO.
Preparation of In_2O_3 Nanwires by Sol-gel Template Technology and Their Gas Sensing Property

Han Gao-rong

2010-01-01

Nanoscience and Nanotechnology

Abstract:AAM template was employed to fabricate cubic In2O3 nanowires by sol-gel template using NH2CH2CH2NH2 and InCl3·4H2O as precursor. The structure, morphology and grain diameter of In2O3 nanowires were characterized by means of XRD, SEM and TEM. The experiment results show that In2O3 nanowires with diameters ranging from 80 to 100 nm and their grain diameters ranging from 4 to 10 nm were synthesized. The gas sensing property of the sensor fabricated by pre -prepared In2O3 nanowires was investigated. It shows the In2O3 nanowires sensor has high selectivity to NO2 with optimal working temperature 360 ℃
Preparation and bifunctional gas sensing properties of porous In2O3-CeO2 binary oxide nanotubes.

Lin Xu,Hongwei Song,Biao Dong,Yu Wang,Jiansheng Chen,Xue Bai

DOI: https://doi.org/10.1021/ic101602a

IF: 4.6

2010-01-01

Inorganic Chemistry

Abstract:The porous binary In(2)O(3)-CeO(2) oxides nanotubes (NTs) in cubic phase were first fabricated by electrospinning (ESP) method and characterized by SEM, TEM, XRD, XPS and UV-vis absorption techniques. By adjusting the In(2)O(3) and CeO(2) molar ratio, the out diameters and wall thicknesses of the final composites were tuned ranging of 90-180 nm and 15-9 nm, respectively. The band gap of the binary oxides gradually decreases, and the ratio of Ce(3+) to Ce(4+) increases with the increase of CeO(2), implying that surface oxygen vacancies gradually increase. The gas sensing test reveals that when the content of CeO(2) is appropriate, the as fabricated In(2)O(3)-CeO(2) NTs could be bifunctional gas sensors to detect H(2)S at low temperature(25-110 °C) while acetone at relative high temperature (300 °C). The In(75)Ce(25) NTs sensor is an optimum one, which exhibits the highest response of 498 to H(2)S at 80 °C and the highest response of 30 to acetone at 300 °C. In contrast to the pure In(2)O(3) sensor, the response and recovery times, as well as the sensing reaction barrier height, for In(75)Ce(25) both degrade considerably. The above temperature-dependent sensing properties were attributed to two different gas sensing mechanisms, sulfuration at low temperature and adsorption at high temperature.
Preparation and Electrical Properties of Electrospun Tin-Doped Indium Oxide Nanowires

Dandan Lin,Hui Wu,Rui Zhang,Wei Pan

DOI: https://doi.org/10.1088/0957-4484/18/46/465301

IF: 3.5

2007-01-01

Nanotechnology

Abstract:Well-aligned tin-doped indium (ITO) nanowires have been prepared using the electrospinning process. The Sn doping mechanism and microstructure have been characterized by x-ray diffraction (XRD) and x-ray photoelectron spectroscopy (XPS). Devices for I–V measurement and field-effect transistors (FETs) were assembled using ITO nanowires with top contact configurations. The effect of Sn doping on the electrical conductivity was significant in that it enhanced the conductance by over 107 times, up to ∼1 S cm−1 for ITO nanowires with an Sn content of 17.5 at.%. The nanowire FETs were operated in the depletion mode with an electron mobility of up to 0.45 cm2 V−1 s−1 and an on/off ratio of 103.
Remarkable Near-Infrared Temperature Sensing Properties of Y 3 Ga 5 O 12 :Cr 3+ and Y 3 Ga 5 O 12 :Cr 3+ /Yb 3+ Nanotubes Fabricated via a Single-Needle Electrospinning Technique

Zhichao Ren,Hongquan Yu,Jinsu Zhang,Xiangping Li,Sai Xu,Baojiu Chen

DOI: https://doi.org/10.1021/acs.inorgchem.4c03456

IF: 4.6

2024-10-25

Inorganic Chemistry

Abstract:For the first time, nanotubes of Y(3)Ga(5)O(12):Cr^(3+) (referred to as YGO:Cr^(3+)) and Y(3)Ga(5)O(12):Cr^(3+)/Yb^(3+) (referred to as YGO:Cr^(3+)/Yb^(3+)) were produced via a single-needle electrospinning method. The nanotubes of YGO:Cr^(3+) and YGO:Cr^(3+)/Yb^(3+) have outer diameters between 190 and 210 nm, whereas the inner diameter ranges between 70 and 80 nm, and the wall thickness ranges from 50 to 60 nm. The temperature sensitivity of YGO:0.02Cr^(3+) nanotubes was examined by studying...

chemistry, inorganic & nuclear
In Situ Growth of Sno2 Nanosheets on A Substrate Via Hydrothermal Synthesis Assisted by Electrospinning and the Gas Sensing Properties of Sno2/Polyaniline Nanocomposites

Yang Li,Huitao Ban,Mingfei Jiao,Mujie Yang

DOI: https://doi.org/10.1039/c6ra10280h

IF: 4.036

2016-01-01

RSC Advances

Abstract:In situpreparation of SnO2nanosheet/polyaniline composite on a substrate and its applications as a high performance gas sensor.
Rare earth element-doped porous In2O3 nanosheets for enhanced gas-sensing performance

Wen-Hui Zhang,Su-Jun Ding,Qing-Song Zhang,Hui Yi,Zi-Xiang Liu,Meng-Li Shi,Rong-Feng Guan,Lu Yue

DOI: https://doi.org/10.1007/s12598-020-01607-x

IF: 6.318

2021-01-07

Rare Metals

Abstract:Rare earth (La, Pr, Sm, Ce and Yb)-doped porous In2O3 nanosheets are prepared by a solvothermal method. The effect of rare earth elements on the structure, morphologies and gas-sensing performance of In2O3 nanosheets is systematically investigated. The mixed phase composed of c-In2O3 and rh-In2O3 can be transformed into rh-In2O3 by doping with rare earth elements. After doping with rare earth elements, the morphology can be changed from compact nanosheets to porous sheets. Compared with pure In2O3 and La, Pr, Sm, Ce-doped porous In2O3 nanosheets, Yb-doped In2O3 nanosheets present the best gas-sensing performance. Among 3%–10% Yb-doped samples, 6% Yb-doped In2O3 porous nanosheets exhibit the optimal gas-sensing performance to 5 × 10−6–750 × 10−6 acetone, giving a high response of 15.3 toward 50 × 10−6 acetone and fast response/recovery time at the operating temperature of 220 °C. Moreover, 6% Yb-doped porous In2O3 nanosheet sensor also exhibits excellent selectivity and stability, indicating its potential in the next-generation gas sensor.<h3 class="a-plus-plus">Graphic abstract</h3>

materials science, multidisciplinary,metallurgy & metallurgical engineering
Synthesis and Ethanol Sensing Properties of SnO2 Nanoparticles in SnO2 Nanotubes Composite

Feng Li,Ma Qianli,Yu Wensheng,Dong Xiangting,Wang Jinxian,Liu Guixia

DOI: https://doi.org/10.1134/s0036024420110242

2020-01-01

Abstract:Multidimensional nanostructures (0D–1D composite nanostructure) SnO2 nanoparticles in SnO2 nanotubes were easily synthesized by combining the co-precipitation method with the coaxial electrospinning method. SnO2 nanoparticles with a size of about 30 nm were synthesized by co-precipitation method, and SnO2 nanoparticles in SnO2 nanotubes were synthesized by coaxial electrospinning by using a dispersion of SnO2 nanoparticles as the inner precursor. Such 0D–1D SnO2 nanostructures have advantages of the enhanced gas sensing performances due to the improved specific surface area and gas accessibility. The multidimensional nanostructures SnO2 nanoparticles in SnO2 nanotubes exhibit an enhanced gas sensing performances in comparison to 0D SnO2 nanoparticles and 1D SnO2 nanotubes.
Role of nickel dopant on gas response and selectivity of electrospun indium oxide nanotubes

Jinglong Bai,Qiao Wang,Yanrong Wang,Xu Cheng,Zhenyu Yang,Xiuyun Gu,Baoyu Huang,Gengzhi Sun,Zhenxing Zhang,Xiaojun Pan,Jin Yuan Zhou,Erqing Xie

DOI: https://doi.org/10.1016/j.jcis.2019.10.090

2020-02-15

Abstract:It has been demonstrated that the incorporation of Ni into metal oxide-based gas sensors often enhances the sensing performance by increasing the catalytic and heterojunction effects. However, it remains unclear how these two effects work either individually or synergistically in gas sensing. Herein, a series of Ni-doped In2O3 nanotubes (NIO NTs) with different doping concentrations were synthesized through a traditional electrospinning technique. The as-prepared NIO NTs were uniform, with length of micron scale, an average diameter of approximately 70 nm, and a tube wall thickness of approximately 10 nm. Following their incorporation into gas sensors, the NIO NTs often showed improved sensing properties (including excellent response and selectivity) for ethanol vapor compared to the pristine In2O3 NTs. Specifically, at 100 ppm ethanol and 220 °C, the response of NIO-7 NTs (7 mol% Ni) was approximately four-fold higher than that of pristine In2O3 NTs (49.74 vs. 13.39). The gas sensing test results indicated that the improved sensing performance was due to the formation of a heterojunction between In2O3 and NiO, as well as to the catalysis effects of Ni3+ ions. Additionally, simulation results indicated that the improved gas selectivity could be due to the Ni doping-induced change in surface adsorption energies of the tested gases.
Porous Cobalt Oxide Nanowires: Notable Improved Gas Sensing Performances

MaiXia Ma,ZhiYun Pan,Lin Guo,JingHong Li,ZiYu Wu,ShiHe Yang

DOI: https://doi.org/10.1007/s11434-012-5363-0

2012-01-01

Abstract:The porous Co 3 O 4 nanowires have been successfully synthesized via modified template method. A possible growth mechanism governing the formation of such 1D nanowires is proposed. The as-prepared products have been characterized by X-ray Powder Diffraction (XRD), Extended X-ray Absorption Fine-structure (EXAFS), High-resolution Transmission Electron Microscopy (HRTEM) and N 2 adsorption/desorption analysis. Our systematic studies have revealed that the porous Co 3 O 4 nanowires show excellent gas sensing performances, which demonstrate the potential application of the 1D nanostructured Co 3 O 4 in the detection of the ethanol gas as a sensor material. The improved performances are owing to its large specific surface area and porous morphology.
Preparation and morphology controlling of Co3O4 nanostructures and their gas-sensing properties

Lehang Cheng,Yuankun Wang,Zhidong Lin,Liming Liu,Xiaowen Zhang

DOI: https://doi.org/10.1557/s43579-024-00545-4

2024-03-21

MRS Communications

Abstract:Co3O4 nanorods and nanosheets were prepared via a facile fluorine-mediated hydrothermal method, followed by thermal conversion. Both the Co3O4 nanorods and nanosheets exhibited a spinel structure, assembling by 30 nm nanograin along one and two dimensions. The primary exposed facet of the Co3O4 nanorods was identified as (110), while the main exposed plane of the Co3O4 nanosheets was (112). Gas sensing results showed the Co3O4 nanorods sensor exhibited higher sensitivity. The Co3O4 nanorods sensor demonstrated excellent sensitivities to toluene and xylene at 200°C, making it a promising candidate for the detection of these specific volatile organic compounds. The response of the Co3O4 nanorods sensor to the test gases at 200°C.

materials science, multidisciplinary
Porous Hierarchical In2o3 Micro-/Nanostructures: Preparation, Formation Mechanism, And Their Application In Gas Sensors For Noxious Volatile Organic Compound Detection

Jinyun Liu,Tao Luo,Fanli Meng,Kai Qian,Yuteng Wan,Jinhuai Liu

DOI: https://doi.org/10.1021/jp911768m

2010-01-01

Abstract:A porous hierarchical In2O3 micro-/nanostructure was prepared by oxidizing In2S3 precursors for gas sensor applications. The formation mechanism of the porous structure was investigated systemically by means of simultaneous thermogravimetry and differential thermal analysis, conventional X-ray diffraction, and energy-dispersive XRD cooperated with field-emission scanning electronic microscopy observations. In gas-sensing measurements with noxious volatile organic compounds as target gases, the gas sensor based on porous hierarchical In2O3 micro-/nanostructures showed a sensitive performance with a large detecting concentrations range. Besides, the as-fabricated gas sensor also exhibited significant selectivity toward each target gas. Both the sensitivity and the selectivity of the porous hierarchical In2O3 micro-/nanostructure-based gas sensor enable it to be potentially applied for environmental monitoring toward noxious volatile organic compounds. Furthermore, the gas-sensing mechanism was also demonstrated from the kinetic process of gas adsorption-desorption.
Indium Telluride Nanotubes: Solvothermal Synthesis, Growth Mechanism, and Properties

Liyan Zhou,Shancheng Yan,Tao Lu,Yi Shi,Jianyu Wang,Fan Yang

DOI: https://doi.org/10.1016/j.jssc.2013.11.033

IF: 3.3

2014-01-01

Journal of Solid State Chemistry

Abstract:A convenient solvothermal approach was applied for the first time to synthesize In2Te3 nanotubes. The morphology of the resultant nanotubes was studied by scanning electron microscopy and transmission electron microscopy. Nanotubes with a relatively uniform diameter of around 500nm, tube wall thickness of 50–100nm, and average length of tens of microns were obtained. X-ray diffraction, X-ray photoelectron spectroscopy, and Raman spectroscopy were used to study the crystal structures, composition, and optical properties of the products. To understand the growth mechanism of the In2Te3 nanotubes, we studied the influences of temperature, reaction time, and polyvinylpyrrolidone (PVP) and ethylene diamine (EDA) dosages on the final products. Based on the experimental results, a possible growth mechanism of In2Te3 nanotubes was proposed. In this mechanism, TeO3−2 is first reduced to allow nucleation. Circumferential edges of these nucleated molecules attract further deposition, and nanotubes finally grow rapidly along the c-axis and relatively slowly along the circumferential direction. The surface area of the products was determined by BET and found to be 137.85m2g−1. This large surface area indicates that the nanotubes may be suitable for gas sensing and hydrogen storage applications. The nanotubes also showed broad light detection ranging from 300nm to 1100nm, which covers the UV–visible–NIR regions. Such excellent optical properties indicate that In2Te3 nanotubes may enable significant advancements in new photodetection and photosensing applications.

Porous In2O3:RE (RE = Gd, Tb, Dy, Ho, Er, Tm, Yb) Nanotubes: Electrospinning Preparation and Room Gas-Sensing Properties

Porous In<sub>2</sub>O<sub>3</sub>:RE (RE = Gd, Tb, Dy, Ho, Er, Tm, Yb) Nanotubes: Electrospinning Preparation and Room Gas-Sensing Properties

Synthesis and Photoluminescence of Y2O3:RE3+ (re=eu, Tb, Dy) Porous Nanotubes Templated by Carbon Nanotubes.

In(OH)3particles from an Ionic Liquid Precursor and Their Conversion to Porous In2O3particles for Enhanced Gas Sensing Properties

High-performance acetone sensor based on electrospun Tb-doped a-Fe<sub>2</sub>O<sub>3</sub> nanotubes

Synthesis and photoluminescence of Y 2O 3:RE 3+(RE = Eu, Tb, Dy) porous nanotubes templated by carbon nanotubes

The fabrication of In2O3 nanowire and nanotube by single nozzle electrospinning and their gas sensing property

NiO@ZnO Heterostructured Nanotubes: Coelectrospinning Fabrication, Characterization, and Highly Enhanced Gas Sensing Properties.

Porous Indium Oxide Nanotubes: Layer-by-Layer Assembly on Carbon-Nanotube Templates and Application for Room-Temperature NH3 Gas Sensors

Preparation of In_2O_3 Nanwires by Sol-gel Template Technology and Their Gas Sensing Property

Preparation and bifunctional gas sensing properties of porous In2O3-CeO2 binary oxide nanotubes.

Preparation and Electrical Properties of Electrospun Tin-Doped Indium Oxide Nanowires

Remarkable Near-Infrared Temperature Sensing Properties of Y 3 Ga 5 O 12 :Cr 3+ and Y 3 Ga 5 O 12 :Cr 3+ /Yb 3+ Nanotubes Fabricated via a Single-Needle Electrospinning Technique

In Situ Growth of Sno2 Nanosheets on A Substrate Via Hydrothermal Synthesis Assisted by Electrospinning and the Gas Sensing Properties of Sno2/Polyaniline Nanocomposites

Rare earth element-doped porous In2O3 nanosheets for enhanced gas-sensing performance

Synthesis and Ethanol Sensing Properties of SnO2 Nanoparticles in SnO2 Nanotubes Composite

Role of nickel dopant on gas response and selectivity of electrospun indium oxide nanotubes

Porous Cobalt Oxide Nanowires: Notable Improved Gas Sensing Performances

Preparation and morphology controlling of Co3O4 nanostructures and their gas-sensing properties

Porous Hierarchical In2o3 Micro-/Nanostructures: Preparation, Formation Mechanism, And Their Application In Gas Sensors For Noxious Volatile Organic Compound Detection

Indium Telluride Nanotubes: Solvothermal Synthesis, Growth Mechanism, and Properties