Abstract:Given that many mines around the world are located in areas where fresh water is scarce, and companies are being held to increasingly stringent sustainability and environmental responsibility standards, many mines are looking to use locally available saline groundwater or seawater as mixing water in cemented paste backfill (CPB). However, the impacts of this decision on key engineering properties of CPB (e.g. strength and self-desiccation) that affect its mechanical stability need to be better understood to allow confident selection of this practical and more sustainable solution. Thus, the effect of mixing water salinity and binder type on the strength (unconfined compressive strength, UCS) development and self-desiccation (measured by suction and volumetric water content) of CPB is explored in this research. NaCl concentrations from 0 to 300 g/L were used in CPB made with silica tailings and Portland cement type I (PC). Concentrations of 10 and 35 g/L were found to moderately increase UCS, while a concentration of 100 g/L had comparable UCS to non-saline CPB and a concentration of 300 g/L was found to significantly decrease UCS over all curing times. The overall trend is 10 g/L > 35 g/L > 0 g/L > 100 g/L > 300 g/L. The UCS of the 60-day-old CPB with a NaCl of 300 g/L is significantly lower, registering a 26% decrease compared to the UCS of the 60-day-old CPB without salt. In contrast, the UCS of the 60-day-old CPBs containing 10 g/L and 35 g/L of salt exhibits a notable improvement, being 15% and 10% higher, respectively, than the UCS of the 60-day-old CPB without salt. Water content and suction monitoring were conducted up to 28 days of curing time, and it was found that suction only slightly contributed to UCS gain of the saline CPB, and high salt contents (100 and 300 g/L) significantly inhibited the self-desiccation ability of CPB due to inhibition of cement hydration by the excessive amount of salt. The increase in strength of both saline and non-saline samples was attributed primarily to the increase in cement hydration products, while the increased strength of the samples with salinities of 10 and 35 g/L was mainly attributed to the enhancement of the binder hydration due to the low amount of salt and the presence of Friedel’s salt in the pores. The effect of PC replacement by 25 to 75% with slag on CPB with 35 g/L mixing water salinity was also studied. Slag replacement of 50% and higher resulted in significantly higher UCS over most curing times. Suction likely moderately contributed to UCS of the saline CPB with slag, in addition to the presence of Friedel’s salt in the pores and the acceleration of cement and slag hydration by the presence of NaCl.

Effects of Pre-Setting Chemical Exchanges on Geopolymers Cast in Saline Waters

Characteristics of Underwater Cast and Cured Geopolymers

Study the Mechanical Properties of Geopolymer under Different Curing Conditions

Resistance of Chloride and Sulfate of Geopolymer based on fly ash and silica fume as alternative raw materials.

The Effect of Various Si/Al, Na/Al Molar Ratios and Free Water on Micromorphology and Macro-Strength of Metakaolin-Based Geopolymer

Research on the mechanical properties and mechanism of alkali-activated saline soil composite materials

Chloride resistance of class C/class F fly ash-based geopolymer mortars with different strength grades

Alkali-Activated Binders as Sustainable Alternatives to Portland Cement and Their Resistance to Saline Water

The Failure Mechanisms of Precast Geopolymer after Water Immersion

Associated Effects of Sodium Chloride and Dihydrate Gypsum on the Mechanical Performance and Hydration Properties of Slag-Based Geopolymer

The Influence of Particle Size and Calcium Content on Performance Characteristics of Metakaolin- and Fly-Ash-Based Geopolymer Gels

The influence of fly ash-based geopolymer on the mechanical properties of OPC-solidified soil

Investigation of the Mechanical Properties of Quick-Strength Geopolymer Material Considering Preheated-to-Room Temperature Ratio of Sand, Na2SiO3-to-NaOH Ratio, and Fly Ash-to-GGBS Ratio

Efflorescence of fly ash-based geopolymer mortars under quasinatural conditions: The relationship between curing temperature, ion transport, and compressive strength

Effect of Salinity on Strength Behavior of Cement-treated Dredged Clay at High Initial Water Contents

The Effect of Sodium Silicate to NaOH Ratio on Strength Development of Fly Ash Geopolymer Mortar in Marine Environment

Effects SiO2/Na2O molar ratio on mechanical properties and the microstructure of nano-SiO2 metakaolin-based geopolymers

Strength development and self-desiccation of saline cemented paste backfill

Mechanical Properties of Geopolymers Synthesized from Fly Ash and Red Mud under Ambient Conditions

Experiment on Compressive Properties and Microscopic Analysis of Sea Sand Geopolymer-Based Recycled Concrete

Effect of Calcium on the Setting Time and Mechanical Property of a Red Mud-Blast Furnace Slag-Based Geopolymer