Abstract:Mineral geopolymer binders can be an attractive and more sustainable alternative to traditional Portland cement materials for special applications. In geopolymer technology the precursor is a source of silicon and aluminium oxides, the second component is an alkaline solution. In the synthesis of geopolymer binders the most commonly used alkaline solution is a mixture of sodium or potassium water glass with sodium or potassium hydroxide or silicate solution with a low molar ratio, which is more convenient and much safer in use. In this paper, we present the influence of sodium or potassium silicate solution on the physical and mechanical properties of fly ash and ground granulated blast furnace slag-based geopolymer mortars. Mercury intrusion porosimetry and microstructural observation allowed for comparing the structure of materials with a different type of alkaline solution. The evolution of compressive and flexural tensile strength with time determined for composites using 10%, 30% and 50% slag contents (referring to fly ash mass) was analysed. The tests were performed after 3, 7, 14 and 28 days. It was observed that, as the amount of slag used increases in the precursor, the strength of the material grows. Mortars with the sodium alkaline solution were characterised by a higher strength at a young age. However, the values of strength 28 days were higher for geopolymers with potassium alkaline solution reaching 75 MPa in compression. Geopolymer mortar microstructure observation indicates a high matrix heterogeneity with numerous microcracks. Matrix defects may be caused by the rapid kinetics of the material binding reaction or shrinkage associated with the drying of the material.

The Failure Mechanisms of Precast Geopolymer after Water Immersion

Compressive Strength and Chloride Resistance of Slag/Metakaolin-Based Ultra-High-Performance Geopolymer Concrete.

Mitigation of efflorescence for multi-componential geopolymer: Influence of steel slag, flue gas desulfurization gypsum and pre-curing periods

Impacts of Alkaline Washing Pretreatment on Municipal Solid Waste Incineration Fly Ash (MSWI FA) and Resulting Geopolymers

Cleaner geopolymer prepared by co-activation of gasification coal fly ash and steel slag: durability properties and economic assessment

Sulfate Resistance of Class C/class F Fly Ash Geopolymers

Research on Compressive and Flexural Properties of Coal Gangue-Slag Geopolymer under Wetting-Drying Cycles and Analysis of Micro-Mechanism

Interfacial Behavior of Slag, Fly Ash, and Red Mud-Based Geopolymer Mortar with Concrete Substrate: Mechanical Properties and Microstructure

Study on the Reinforced Properties of Geopolymer Fibers with a Sustainable Development Role

Immobilization of MSWI Fly Ash Through Geopolymerization: Effects of Water-Wash

Mechanical behavior and microstructure evolution of slag-fly ash based geopolymer stabilized sand

Correlation of Microstructural and Mechanical Properties of Geopolymers Produced from Fly Ash and Slag at Room Temperature

Synergistic Effect of Blended Precursors and Silica Fume on Strength and High Temperature Resistance of Geopolymer

Effects of Steel Slag on Mechanical Properties and Mechanism of Fly Ash–Based Geopolymer

Characteristics of Underwater Cast and Cured Geopolymers

Shrinkage and Mechanical Properties of Fibre-Reinforced Blast Furnace Slag-Steel Slag-Based Geopolymer

Incorporating steel slag in the production of high heat resistant FA based geopolymer paste via pressure molding

Study on the Chloride–Sulfate Resistance of a Metakaolin-Based Geopolymer Mortar

Performance deterioration of municipal solid waste incineration fly ash-based geopolymer under sulfuric acid attack

The Strength and Microstructure of Two Geopolymers Derived from Metakaolin and Red Mud-Fly Ash Admixture: A Comparative Study

Strength and Microstructure Characteristics of Blended Fly Ash and Ground Granulated Blast Furnace Slag Geopolymer Mortars with Na and K Silicate Solution