Abstract:The low-cycle fatigue of strongly-textured Mg alloys is dominated mainly by an alternation of twinning-detwinning process, which poses a great challenge to conventional constitutive models. As a result, a good reproduction of both mechanical response and deformation behavior often fails in previous simulations, in particular for high strain amplitudes. In the present study, the numerical simulations of low-cycle fatigue behavior of an Mg AZ31 plate with a ± 2% axial strain amplitude along the rolling direction were conducted, using a modified crystal-plasticity based on the finite strain elastic-viscoplastic self-consistent model containing twinning and detwinning mechanisms (EVPSC-TDT), and the results were compared with the mechanical response and deformation behavior determined by a real-time in-situ neutron diffraction. The simulations well predict the hysteresis loops and cyclic-hardening responses throughout the whole fatigue life (80 cycles), along with the evolution of the maximum twin volume fraction and residual twins. For the first time, the evolution of lattice strain throughout the whole fatigue life was calculated, and the results are in good accordance with that determined by neutron diffraction. The present study strongly demonstrates that the EVPSC-TDT model is very effective for modeling the low-cycle fatigue behavior of Mg alloys. More details about the evolution of the maximum twin volume fraction with fatigue cycles are found, an increase from 1st to 2nd cycle, followed by a decrease from 2nd to 20th cycle and a secondary increase after 20th cycle. This finding corrects the previous opinion that the maximum twin volume fraction increases at the initial stage and tends to be saturated at the late stage. Combining the results of simulations and neutron diffractions, the corresponding reasons are explained. Afterward, the mechanisms of the cyclic-hardening behavior at tension stage and compression stage are revisited, and some new insights are provided.

A remarkable improvement of low-cycle fatigue resistance of high-Mn austenitic TWIP alloys with similar tensile properties: Importance of slip mode

Low-Cycle Fatigue Behavior of A High Manganese Austenitic Twin-Induced Plasticity Steel

Forecasting Low-Cycle Fatigue Performance of Twinning-Induced Plasticity Steels: Difficulty and Attempt

Fatigue Deformation Behavior of Fe-Mn-C-(Al) TWIP Steels

Strain Hardening Model of Twip Steels with Manganese Content

Effect of Manganese Content on Tensile Deformation Behavior of Fe-Mn-C TWIP Steels

Fatigue-resistant design in low-cycle regime by regulating the micro-structural gradient in a TWIP steel: Modelling and experiment

Influence of carbon addition on mechanical properties of Fe–Mn–C twinning-induced plasticity steels

On the Tensile Behavior of High-Manganese Twinning-Induced Plasticity Steel

The Role of Mn on Twinning Behavior and Tensile Properties of Coarse- and Fine-Grained Fe–Mn–C Twinning-Induced Plasticity Steels

Effect of Mn content on low-cycle fatigue behaviors of low-carbon bainitic steel

Experimental study on low cycle fatigue behavior of TWIP steel under cyclic shear loading condition

Correlation Between Microstructure Evolution and Mechanical Response in a Moderately Low Stacking-Fault-energy Austenitic Fe–Mn–Si–Al Alloy During Low-Cycle Fatigue Deformation

The tensile properties and microstructure evolution of cold-rolled Fe–Mn–C TWIP steels with different carbon contents

The relative contributions of TWIP and TRIP to strength in fine grained medium-Mn steels

Effect of Al on the Low Cycle Fatigue Deformation Behavior and Microstructure Evolution of Fe–22Mn-0.6C TWIP Steel

Fatigue Crack Growth Behavior of a Coarse- and a Fine-Grained High Manganese Austenitic Twin-Induced Plasticity Steel

Cyclic Deformation Behavior of a New N+C Alloying Austenitic Manganese Steel

Crystal plasticity modeling of low-cycle fatigue behavior of an Mg-3Al-1Zn alloy based on a model, including twinning and detwinning mechanisms

LOW‐CYCLE FATIGUE INVESTIGATIONS AND NUMERICAL SIMULATIONS ON DUAL PHASE STEEL WITH DIFFERENT MICROSTRUCTURES

Microstructure Evolution and Work Hardening Behavior of Medium/high Carbon Fe-Mn-C TWIP Steel During Tensile Deformation at 298 K and 223 K