Abstract:LMP‐LCO cathodes with Mg‐doping and LMP‐LPO coating exhibit stable ultra‐high‐voltage cycling and high structural reversibility, enhancing capacity retention after long‐term cycling. The optimization of both bulk and surface leads to improved interfacial stability, changing the intrinsic electronic structure of LCO cathode materials and affecting their redox reactions. This study provides a new avenue for high‐voltage LCO batteries. Stable cycling of LiCoO2 (LCO) cathode at high voltage is extremely challenging due to the notable structural instability in deeply delithiated states. Here, using the sol–gel coating method, LCO materials (LMP‐LCO) are obtained with bulk Mg‐doping and surface LiMgPO4/Li3PO4 (LMP/LPO) coating. The experimental results suggest that the simultaneous modification in the bulk and at the surface is demonstrated to be highly effective in improving the high‐voltage performance of LCO. LMP‐LCO cathodes deliver 149.8 mAh g−1@4.60 V and 146.1 mAh g−1@4.65 V after 200 cycles at 1 C. For higher cut‐off voltages, 4.70 and 4.80 V, LMP‐LCO cathodes still achieve 144.9 mAh g−1 after 150 cycles and 136.8 mAh g−1 after 100 cycles at 1 C, respectively. Bulk Mg‐dopants enhance the ionicity of CoO bond by tailoring the band centers of Co 3d and O 2p, promoting stable redox on O2−, and thus enhancing stable cycling at high cut‐off voltages. Meanwhile, LMP/LPO surface coating suppresses detrimental surface side reactions while allowing facile Li‐ion diffusion. The mechanism of high‐voltage cycling stability is investigated by combining experimental characterizations and theoretical calculations. This study proposes a strategy of surface‐to‐bulk simultaneous modification to achieve superior structural stability at high voltages.

Improving the Cycling Stability of LiCoO2 at 4.5 V by Mg Doping and Graphite Coating

Mixed Lithium Ion and Electron Conducting LiAlPO 3.93 F 1.07 -Coated LiCoO 2 Cathode with Improved Electrochemical Performance

Improving the cycling stability of LiCoO 2 at 4.5V through co-modification by Mg doping and zirconium oxyfluoride coating

Stable Cycling of LiCoO2 at 4.55 V Enabled by Combined Mg Doping and Surface Coating of NASICON-type Electrolyte

Enhanced cycle stability of LiCoO2 at high voltage by mixed conductive Li7.5La3Zr1.5Co0.5O12 coating

Simultaneously Constructing a TiO2–LiF Composite Coating Enhancing the Cycling Stability of LiCoO2 at 4.6 V High Voltage

Nanoscale Control and Tri-Element Co-Doping of 4.6 V LiCoO2 with Excellent Rate Capability and Long-Cycling Stability for Lithium-Ion Batteries.

Lithium-Aluminum-Phosphate Coating Enables Stable 4.6 V Cycling Performance of LiCoO2 at Room Temperature and Beyond

Trace-amount triple-doping of Ti, Mg, and B for improving the stability of lattice structure and discharge capacity of LiCoO 2 at 4.6V

Improved Cycling Stability of LiCoO2 at 4.5 V Via Surface Modification of Electrodes with Conductive Amorphous LLTO Thin Film

Scalable Precise Nanofilm Coating and Gradient Al Doping Enable Stable Battery Cycling of LiCoO2 at 4.7 V

LiMgPO4‐Coating‐Induced Phosphate Shell and Bulk Mg‐Doping Enables Stable Ultra‐High‐Voltage Cycling of LiCoO2 Cathode

LiMgPO<sub>4</sub>-Coating-Induced Phosphate Shell and Bulk Mg-Doping Enables Stable Ultra-High-Voltage Cycling of LiCoO<sub>2</sub> Cathode

Trace-amount Triple-Doping of Ti, Mg, and B for Improving the Stability of Lattice Structure and Discharge Capacity of LiCoO2 at 4.6V

Enhanced High-Voltage Cycling Stability and Rate Capability of Magnesium and Titanium Co-Doped Lithium Cobalt Oxides for Lithium-Ion Batteries

Realizing long-term cycling stability and superior rate performance of 4.5 V–LiCoO2 by aluminum doped zinc oxide coating achieved by a simple wet-mixing method

Improving diffusion kinetics and phase stability of LiCoO2 via surface modification at elevated voltage

A Novel Bifunctional Self‐Stabilized Strategy Enabling 4.6 V LiCoO2 with Excellent Long‐Term Cyclability and High‐Rate Capability

Multi-scale stabilization of high-voltage LiCoO2 enabled by nanoscale solid electrolyte coating

Enhanced Cycling Stability of Microsized Licoo2 Cathode by Li4ti5o12 Coating for Lithium Ion Battery

Stabilizing 4.6 V LiCoO2 via Er and Mg Trace Doping at Li-Site and Co-Site Respectively