Tm/Al co-doped photonic crystal fiber prepared by laser additive manufacturing technology

Nan Zhao,Jiantao Liu,Yun Chen,Mengmeng Zhu,Zhiyun Hou,Guiyao Zhou

DOI: https://doi.org/10.1364/lst.2019.lw1e.1

2019-01-01

Abstract:The Tm/Al co-doped silica glass was fabricated by the laser additive manufacturing technology. The corresponding Tm/Al co-doped photonic crystal fiber (PCF) performed 13.5 % slope efficiency with nearly 600 mW output laser power.

What problem does this paper attempt to address?

Tm/Al Co-Doped Silica Glass Prepared by Laser Additive Manufacturing Technology for 2-Μm Photonic Crystal Fiber Laser

Jiantao Liu,Nan Zhao,Yun Chen,Mengmeng Zhu,Jiaming Li,Siyuan Rong,Zhiyun Hou,Guiyao Zhou

DOI: https://doi.org/10.1109/jlt.2019.2954881

IF: 4.7

2020-01-01

Journal of Lightwave Technology

Abstract:In this article, we demonstrated the Tm/Al co-doped silica glass fabricated by the laser additive manufacturing technology for the first time. The measurements show that the glass was doped with Tm3+ concentration of 1.64 wt% without any crystallization. The Tm3+ and Al3+ were uniformly distributed, and no additional defects were introduced during the fabrication process. The glass exhibits low hydroxyl content level of 11.56 ppm. Using the prepared silica glass as the core rod, a Tm/Al co-doped photonic crystal fiber (PCF) was fabricated and performed 13.9% slope efficiency with nearly 600 mW output laser power. This novel technology provides an alternative method to fabricate Tm-doped fiber materials with high homogeneity and large core size, promoting the further spread and development of 2 μm fiber lasers.
Fabrication of Optical Cavities with Femtosecond Laser Pulses

Jintian Lin,Jiangxin Song,Jialei Tang,Wei Fang,Koji Sugioka,Ya Cheng

DOI: https://doi.org/10.1117/12.2041353

2014-01-01

Abstract:We report on fabrication of three-dimensional (3D) high-quality (Q) whispering-gallery-mode microcavities by femtosecond laser micromachining. The main fabrication procedures include the formation of on-chip freestanding microdisk through selective material removal by femtosecond laser pulses, followed by surface smoothing processes (CO2 laser reflow for amorphous glass and focused ion beam (FIB) sidewall milling for crystalline materials) to improve the Q factors. Fused silica microcavities with 3D geometries are demonstrated with Q factors exceeding 106. A microcavity laser based on Nd:glass has been fabricated, showing a threshold as low as 69μW via free space continuous-wave optical excitation at the room temperature. CaF2 crystalline microcavities with Q factor of ~4.2×104 have also been demonstrated. This technique allows us to fabricate 3D high-Q microcavities in various transparent materials such as glass and crystals, which will benefit a broad spectrum of applications such as nonlinear optics, quantum optics, and bio-sensing.
All-Solid Silicate Photonic Crystal Fiber Laser with 13.1 W Output Power and 64.5% Slope Efficiency

Longfei Wang,Wentao Li,Qiuchun Sheng,Qinling Zhou,Lei Zhang,Lili Hu,Jianrong Qiu,Danping Chen

DOI: https://doi.org/10.1109/jlt.2014.2298099

IF: 4.7

2014-01-01

Journal of Lightwave Technology

Abstract:We demonstrate an all-solid Nd 3+-doped silicate photonic crystal fiber with 13.1 W output power at 1061 nm and 64.5% slope efficiency. We also theoretically investigate and prove the effects of confinement loss and overlap fraction on a double-clad photonic crystal fiber laser. An innovative design is suggested to improve the laser beam quality.
A Nano-Patterned Photonic Crystal Laser With A Dye-Doped Liquid Crystal

doohyun ko,s m morris,alexander lorenz,f castles,haider butt,d j gardiner,malik m qasim,bodo h wallikewitz,philip j w hands,t d wilkinson,g a j amaratunga,h j coles,friend richard h

DOI: https://doi.org/10.1063/1.4816243

IF: 4

2013-01-01

Applied Physics Letters

Abstract:Covering a nano-patterned titanium dioxide photonic crystal (PC) within a well-oriented film of dye-doped liquid crystal (LC), a distributed feedback laser is constructed whereby the emission characteristics can be manipulated in-situ using an electric field. This hybrid organic-inorganic structure permits simultaneous selectivity of both the beam pattern and laser wavelength by electrical addressing of the LC director. In addition, laser emission is obtained both in the plane and normal to the PC. Along with experimental data, a theoretical model is presented that is based upon an approximate calculation of the band structure of this birefringent, tuneable laser device. (C) 2013 AIP Publishing LLC.
Phosphate Single Mode Large Mode Area All-Solid Photonic Crystal Fiber With Multi-Watt Output Power

longfei wang,hui liu,dongbing he,chunlei yu,lili hu,jianrong qiu,danping chen

DOI: https://doi.org/10.1063/1.4870630

IF: 4

2014-01-01

Applied Physics Letters

Abstract:An index-depressed active core, single-mode phosphate all-solid large-mode-area photonic crystal fiber (PCF) is theoretically investigated using full-vectorial finite difference approach and experimentally realized. The PCF has a maximum output power of 5.4 W and 31% slope efficiency. Single-mode operation is realized through PCFs with core diameters of 30, 35, and 40 mu m, respectively. The beam quality is not degraded even at maximum output power. Our simulations and experiments reveal that the laser performance is significantly affected by the center-to-center distance between the two nearest rods K, the rod diameter d, and their ratio d/Lambda, implying that much attention should be given in employing optimal parameters to achieve excellent laser performance. (C) 2014 AIP Publishing LLC.
Yb-Doped Aluminophosphosilicate Laser Fiber

Cong Gao,Zhihua Huang,Yuying Wang,Huan Zhan,Li Ni,Kun Peng,Yuwei Li,Zhaonian Jia,Xiaolong Wang,Ani You,Xiaoyu Xiang,Jianjun Wang,Feng Jing,Honghuan Lin,Aoxiang Lin

DOI: https://doi.org/10.1109/jlt.2016.2602372

IF: 4.7

2016-11-15

Journal of Lightwave Technology

Abstract:By using modified chemical vapor deposition system combined with chelate precursor doping technique, we report on the fabrication and characterization of Yb-doped aluminophosphosilicate (Al2O3-P2O 5-SiO2) laser fiber. Based on a master oscillator power amplifier laser setup and pumped directly by 976 nm laser diodes, 3.1 kW laser at 1064 nm was achieved with a slope efficiency of 78.4. Benefiting from codoped Al and P, the laser output power showed no evidence of roll-over. The linear fitting of the output power versus the pump power shows the potentiality for further power scaling. The results indicate that chelate precursor doping technique is a competitive method for rare-earth-ion-doped fiber preform fabrication, and aluminophosphosilicate host material has potentiality to develop multi-kW level laser fibers.

engineering, electrical & electronic,optics,telecommunications
Enhanced CW Lasing and Q‐Switched Pulse Generation Enabled by Tm3+‐Doped Glass Ceramic Fibers

Shiliang Kang,Tian Qiao,Xiongjian Huang,Changsheng Yang,Xiaofeng Liu,Jianrong Qiu,Zhongmin Yang,Guoping Dong

DOI: https://doi.org/10.1002/adom.202001774

IF: 9

2020-01-01

Advanced Optical Materials

Abstract:Fiber lasers, owing to the high beam quality and super robustness, are widely used in fields from optical communications, fiber sensing, biomedicine to material processing. The use of glass fibers as the gain medium has, however, posed a strong obstacle for improving efficiency and, especially, achieving efficient lasing action in the mid-infrared (MIR) region, because of the relatively large nonradiative energy loss. Here, the fabrication of a Tm3+-doped tellurate glass-ceramic (GC) fiber is demonstrated, which enables enhanced lasing action at approximate to 2 mu m. Compared with the as-prepared fiber, the optical conversion efficiency of GC fiber is increased from 8.8% to 14.1%. The microstructure and spectral characterization analyses suggest that the improvement of the laser performance in GC fiber is induced by the significant change of the local environment surrounding Tm3+ ions due to the formation of nanocrystals within the glass fibers. Moreover, the developed GC fiber also enables Q-switched pulsed laser output at approximate to 2 mu m with a pulse energy of 3.2 J and pulse width of 4.1 ns. The results demonstrated here may have strong implications in the development of MIR fiber lasers and the applications of GC fibers in MIR photonics.
Phosphate Ytterbium-Doped Single-Mode All-Solid Photonic Crystal Fiber with Output Power of 13.8 W

Longfei Wang,Dongbing He,Suya Feng,Chunlei Yu,Lili Hu,Jianrong Qiu,Danping Chen

DOI: https://doi.org/10.1038/srep08490

IF: 4.6

2015-01-01

Scientific Reports

Abstract:Single-mode ytterbium-doped phosphate all-solid photonic crystal fiber (AS-PCF) with 13.8 W output power and 32% slope efficiency was reported. By altering the diameter of the rods around the doped core and thus breaking the symmetry of the fiber, a polarization-maintaining AS-PCF with degree of polarization of >85% was also achieved, for the first time to knowledge, in a phosphate PCF.
Fabrication and Characterization of Glass‐Ceramic Fiber‐Containing Cr3 + ‐doped ZnAl2O4 Nanocrystals

Zaijin Fang,Shupei Zheng,Wencai Peng,Hang Zhang,Zhijun Ma,Shifeng Zhou,Danping Chen,Jianrong Qiu

DOI: https://doi.org/10.1111/jace.13716

IF: 4.186

2015-01-01

Journal of the American Ceramic Society

Abstract:Glass-ceramic fibers containing Cr3+-doped ZnAl2O4 nanocrystals were fabricated by the melt-in-tube method and successive heat treatment. The obtained fibers were characterized by electro-probe micro-analyzer, X-ray diffraction, Raman spectrum and high-resolution transmission electron microscopy. In our process, fibers were precursor at the drawing temperature where the fiber core glass was melted while the clad was softened. No obvious element interdiffusion between the core and the clad section or crystallization was observed in precursor fiber. After heat treatment, ZnAl2O4 nanocrystals with diameters ranging from 1.0 to 6.3 nm were precipitated in the fiber core. In comparison to precursor fiber, the glass-ceramic fiber exhibits broadband emission from Cr3+ when excited at 532 nm, making Cr3+-doped glass-ceramic fiber a promising material for broadband tunable fiber laser. Furthermore, the melt-in-tube method demonstrated here may open a new gate toward the fabrication of novel glass-ceramic fibers.
Spectroscopic and Laser Properties of Al-P Co-Doped Yb Silica Fiber Core-Glass Rod and Large Mode Area Fiber Prepared by Sol-Gel Method

Shikai Wang,Wenbin Xu,Fengguang Lou,Lei Zhang,Qinling Zhou,Danping Chen,Wei Chen,Suya Feng,Meng Wang,Chunlei Yu,Lili Hu

DOI: https://doi.org/10.1364/ome.6.000069

2015-01-01

Optical Materials Express

Abstract:A large-size (∅5 mm) Yb3+-doped silica fiber core-glass rod with an Al-P co-doped composition: 0.035Yb2O3-1.0Al2O3-1.0P2O5-97.965SiO2 (mol%) was prepared by the sol-gel method combined with high-temperature melting technology. We successfully solved the doping homogeneity problem caused by the volatility of P2O5. The doping homogeneity of the glass rod was very high with the maximum refractive index fluctuation Δn < 2 × 10−4. The refractive index of the glass rod was very low because of the equimolar amounts of Al and P co-doping, which yielded an AlPO4 structure. A large-mode-area single cladding fiber (LMA SCF) and photonic crystal fiber (LMA PCF) with core diameters of 35 and 50 µm, respectively, were drawn from this glass rod. Owing to the low refractive index of the core-glass rod and the corresponding low numerical aperture (NA, 0.033) of the core, the LMA SCF exhibited a high laser beam brightness with M2 = 1.3-1.4. The LMA PCF exhibited the maximum output power, which was limited by the available pumping power, of 46 W and the slope efficiency of 61%.
Rectangular Porous-Core Photonic-Crystal Fiber With Ultra-Low Flattened Dispersion and High Birefringence for Terahertz Transmission

Yani Zhang,Xin Jing,Dun Qiao,Lu Xue

DOI: https://doi.org/10.3389/fphy.2020.00370

IF: 3.718

2020-10-08

Frontiers in Physics

Abstract:We propose a novel porous-core photonic crystal fiber (PCF) consisting of asymmetrical rectangular air holes in the core and six-ring hexagonal lattice circular air holes in the cladding for achieving low-loss polarization terahertz transmission in a wide frequency range. By assuming TOPAS as the host material, the finite element method (FEM) is used to investigate its properties. The near-zero flattened dispersion of −0.01±0.02 ps/THz/cm is achieved over a frequency range of 1.0–2.0 THz, as well as a high birefringence of 7.1 × 10−2 which can be useful for polarization-maintaining applications. Also, critical parameters such as mode field distribution, effective material loss, confinement loss, and effective mode area are discussed in detail. Further, fabrication possibilities are discussed briefly by comparing recent work on similar waveguide structures.OCIS Codes: 040.2235 (Far infrared or terahertz), 060.4005 (Micro-structured fibers), 060.2420 (Fibers, polarization-maintaining), 160.5470 (Polymers).

physics, multidisciplinary
Enhanced CW Lasing and Q‐Switched Pulse Generation Enabled by Tm 3+ ‐Doped Glass Ceramic Fibers

Shiliang Kang,Tian Qiao,Xiongjian Huang,Changsheng Yang,Xiaofeng Liu,Jianrong Qiu,Zhongmin Yang,Guoping Dong

DOI: https://doi.org/10.1002/adom.202001774

IF: 9

2020-12-02

Advanced Optical Materials

Abstract:Fiber lasers, owing to the high beam quality and super robustness, are widely used in fields from optical communications, fiber sensing, biomedicine to material processing. The use of glass fibers as the gain medium has, however, posed a strong obstacle for improving efficiency and, especially, achieving efficient lasing action in the mid‐infrared (MIR) region, because of the relatively large nonradiative energy loss. Here, the fabrication of a Tm3+‐doped tellurate glass‐ceramic (GC) fiber is demonstrated, which enables enhanced lasing action at ≈2 µm. Compared with the as‐prepared fiber, the optical conversion efficiency of GC fiber is increased from 8.8% to 14.1%. The microstructure and spectral characterization analyses suggest that the improvement of the laser performance in GC fiber is induced by the significant change of the local environment surrounding Tm3+ ions due to the formation of nanocrystals within the glass fibers. Moreover, the developed GC fiber also enables Q‐switched pulsed laser output at ≈2 µm with a pulse energy of 3.2 J and pulse width of 4.1 ns. The results demonstrated here may have strong implications in the development of MIR fiber lasers and the applications of GC fibers in MIR photonics.

materials science, multidisciplinary,optics
Brillouin Fiber Laser Based on Photonic Crystal Fiber

CHI Hao,ZHANG Xian-min,SHEN Lin-fang

DOI: https://doi.org/10.3785/j.issn.1008-973x.2006.12.023

2006-01-01

Abstract:To improve the output power and the laser efficiency compared with common fiber Brillouin lasers,a small core photonic crystal fiber(PCF) based ring-cavity Brillouin fiber laser was presented.An erbium-doped fiber amplifier and an optical filter were added to the fiber ring,fiber ring loss was compensated and the stimulated emission of the Erbium-doped fiber were suppressed respectively.Experimental results show that the stable Brillouin laser is achieved by the fiber laser using 25 m small core PCF,and that the erbium-doped fiber amplifier in the fiber ring is the major energy source of the output laser.Compared with common single mode fiber,the small core PCF has higher non-linear coefficient and larger Brillouin gain,and is suitable for the gain medium of Brillouin fiber laser.
Research on ytterbium-doped photonic crystal fiber amplifier for the femtosecond fiber laser

Hongchun Tian,Zhiyun Hou,Zhang,Guiyao Zhou,Changming Xia,Wei Zhang,Jiale Wu,Hongzhan liu,Yan Zheng,Sa Zhang

DOI: https://doi.org/10.1088/1054-660x/26/1/015103

IF: 1.2

2015-12-07

Laser Physics

Abstract:We report on a single-stage, high-repetition photonic crystal fiber amplifier working at 1030 nm seeded by a femtosecond fiber laser, which generates an output with average power of 2.23 W at a repetition rate of 49.5 MHz and a 3 dB spectral width of 5 nm, corresponding to a pulse energy of 45.2 nJ. After amplification, the spectrum of the femtosecond laser is broadened. A home-made, ytterbium-doped, double-clad photonic crystal fiber fabricated by laser sintering technology combined with a solution doping method with a core diameter of only 24 μm is used as the power amplifier medium. The spectral characteristics as well as the suppression of amplified spontaneous emission are discussed in detail. Experiment confirms that the amplified spontaneous emission becomes negligible with increasing incident seed power and no obvious nonlinear effects arise in this experiment. These results can provide motivation for the application of ytterbium-doped photonic crystal fiber and can provide a potential application for the high-power, all-fiber laser in the future.

optics,physics, applied
Heavily Yb-doped phosphate large-mode area all-solid photonic crystal fiber operating at 990?nm

longfei wang,dongbing he,suya feng,chunlei yu,lili hu,jianrong qiu,danping chen

DOI: https://doi.org/10.1088/1612-2011/12/7/075102

IF: 1.704

2015-01-01

Laser Physics Letters

Abstract:We demonstrate, for the first time to our knowledge, a 16 wt.% Yb-doped phosphate large-mode area all-solid photonic crystal fiber (AS-PCF) laser operating at 990 nm. By carefully tailoring the absorption and emission properties of the active glass and designing the structure of AS-PCF, the excitation of the 990 nm laser and the depression of the laser above 1 mu m can be easily realized even without any wavelength-selective optics. The single-mode behavior of PCF with a 35 mu m doped core, the largest core diameter of approximately 1 mu m in phosphate fiber, is theoretically investigated by finite-difference time-domain method and experimentally confirmed.
Double-clad large-mode-area polarization-maintaining ytterbium doped photonic crystal fiber

Zhao Nan,Chen Gui,Wang Yi-Bo,Peng Jing-Gang,Li Jin-Yan,

DOI: https://doi.org/10.7498/aps.63.024202

IF: 0.906

2014-01-01

Acta Physica Sinica

Abstract:The Yb3+ doped double clad polarization-maintaining photonic crystal fiber is prepared from SiO2-Al2O3-P2O5 core glass of an optical fiber perform through a conventional modified chemical-vapor deposition technique and solution doping method, which contains a large core of around 30 m in diameter. Through simulated calculation, the mode area of the double clad polarization maintaining photonic crystal fiber reaches about 232 m2 and the double refraction coefficient B can be 510-5. In experiment, amplification tests of both pulse laser and continuous laser are conducted. The first domestic high efficient femtosecond laser amplification is achieved by using the photonic crystal fiber. A 2 m long photonic crystal fiber laser generates up to 1.64 W output power with a slope efficiency of 49.8%. And 5 m long fiber can reach 8.12 W continuous laser output, in which the slope efficiency is 55.9% and performs good amplification effect. Besides, the extinction ratio is about 10 dB, which indicates good polarization performance of the fiber.

physics, multidisciplinary
The Preparation of Yttrium Aluminosilicate (YAS) Glass Fiber with Heavy Doping of Tm3+ from Polycrystalline YAG Ceramics

Yeming Zhang,Guoquan Qian,Xusheng Xiao,Xiangling Tian,Xinqi Ding,Zhijun Ma,Luyun Yang,Haitao Guo,Shanhui Xu,Zhongmin Yang,Jianrong Qiu

DOI: https://doi.org/10.1111/jace.15722

IF: 4.186

2018-01-01

Journal of the American Ceramic Society

Abstract:Yttrium aluminosilicate (YAS) glass core fibers with different doping concentration of Tm3+ were fabricated by a Melt-in-Tube method from YAG polycrystalline ceramics. The effect of Tm3+ concentration on the spectroscopy of YAG ceramics and laser performance of YAS fibers were discussed. A homemade linear all-fiber laser based on the obtained 15% Tm3+-doped YAS fiber shows an optimized slope efficiency of 12.8%. The YAS fibers have been proven to be practical to achieve extremely high Tm3+ doping concentration and are a promising option for the 2.0m laser.
Advances in Silica-Based Large Mode Area and Polarization-Maintaining Photonic Crystal Fiber Research

Yuan Ma,Rui Wan,Shengwu Li,Liqing Yang,Pengfei Wang

DOI: https://doi.org/10.3390/ma15041558

IF: 3.4

2022-02-18

Materials

Abstract:In recent years, photonic crystal fibers (PCFs) have attracted increasing attention. Compared with traditional optical fibers, PCFs exhibit many unique optical properties and superior performance due to their high degree of structural design freedom. Using large-mode area (LMA) fibers with single-mode operation is essential to overcoming emerging problems as the power of fiber lasers scales up, which can effectively reduce the power density and mitigate the influence of nonlinear effects. With a brief introduction of the concept, classification, light transmission mechanism, basic properties, and theoretical analysis methods of PCFs, this paper mainly compiles the worldwide development of large-mode area and polarization-maintaining (PM) PCFs, and finally proposes possible technical routes to realize the single-mode operation of LMA-PCFs and PM-LMA-PCFs. Finally, the future development prospects of the PCFs are discussed.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
40 W picosecond fiber amplifier with the large mode-area polarized crystal fiber

H. Yu,J. Zhou,X. Wushouer,P. Yan,D. Wang,M. Gong

DOI: https://doi.org/10.1002/lapl.200910037

IF: 1.704

2009-01-01

Laser Physics Letters

Abstract:We reported the 5W picosecond laser with pulse width of 30 ps and the repetition rate of 100 MHz, which was amplified to 40.2 W with the linear polarized Yb-doped photonic crystal fiber (PCF), with the slope efficiency of about 58%. As much a 17.3 W second-harmonic power was achieved corresponding to the conversion efficiency of 43%.
Yb/Er co-doped phosphate all-solid single-mode photonic crystal fiber

Longfei Wang,Dongbing He,Suya Feng,Chunlei Yu,Lili Hu,Jianrong Qiu,Danping Chen

DOI: https://doi.org/10.1038/srep06139

IF: 4.6

2014-01-01

Scientific Reports

Abstract:An all-solid Yb 3+ /Er 3+ co-doped single-mode phosphate photonic crystal fiber (PCF) with Watt-level output power and 20 μm core diameter is demonstrated for the first time. A PCF whose refractivity of the active core is lower than that of the background glass is suggested and theoretically confirmed to be in single-mode operation at 40 μm core diameter.

Tm/Al co-doped photonic crystal fiber prepared by laser additive manufacturing technology

Tm/Al Co-Doped Silica Glass Prepared by Laser Additive Manufacturing Technology for 2-Μm Photonic Crystal Fiber Laser

Fabrication of Optical Cavities with Femtosecond Laser Pulses

All-Solid Silicate Photonic Crystal Fiber Laser with 13.1 W Output Power and 64.5% Slope Efficiency

A Nano-Patterned Photonic Crystal Laser With A Dye-Doped Liquid Crystal

Phosphate Single Mode Large Mode Area All-Solid Photonic Crystal Fiber With Multi-Watt Output Power

Yb-Doped Aluminophosphosilicate Laser Fiber

Enhanced CW Lasing and Q‐Switched Pulse Generation Enabled by Tm3+‐Doped Glass Ceramic Fibers

Phosphate Ytterbium-Doped Single-Mode All-Solid Photonic Crystal Fiber with Output Power of 13.8 W

Fabrication and Characterization of Glass‐Ceramic Fiber‐Containing Cr3 + ‐doped ZnAl2O4 Nanocrystals

Spectroscopic and Laser Properties of Al-P Co-Doped Yb Silica Fiber Core-Glass Rod and Large Mode Area Fiber Prepared by Sol-Gel Method

Rectangular Porous-Core Photonic-Crystal Fiber With Ultra-Low Flattened Dispersion and High Birefringence for Terahertz Transmission

Enhanced CW Lasing and Q‐Switched Pulse Generation Enabled by Tm 3+ ‐Doped Glass Ceramic Fibers

Brillouin Fiber Laser Based on Photonic Crystal Fiber

Research on ytterbium-doped photonic crystal fiber amplifier for the femtosecond fiber laser

Heavily Yb-doped phosphate large-mode area all-solid photonic crystal fiber operating at 990?nm

Double-clad large-mode-area polarization-maintaining ytterbium doped photonic crystal fiber

The Preparation of Yttrium Aluminosilicate (YAS) Glass Fiber with Heavy Doping of Tm3+ from Polycrystalline YAG Ceramics

Advances in Silica-Based Large Mode Area and Polarization-Maintaining Photonic Crystal Fiber Research

40 W picosecond fiber amplifier with the large mode-area polarized crystal fiber

Yb/Er co-doped phosphate all-solid single-mode photonic crystal fiber