Abstract:Numerical simulations with the steady 3D RANS were performed on the rear stage of a modern high pressure compressor. The labyrinth seal cavity model of the shrouded stator was simplified according to the actual stator structure, which the seal cavity gap is 1% of blade height. Several typical configurations (shrouded stator, idealized stator and cantilevered stators) were designed and carried out, and cantilevered stators contained no gap, small gap (CS1%), design gap (CS2.5%) and large gap (CS4%/CS5%). The results indicate due to the effect of leakage flow from 1% span seal cavity gap, the total pressure loss of SS is larger than IS, while IS instead of SS in the process of the compressor design, the stall margin will be enlarged nearly 6% numerically. At the design point, when the hub gap is 3.5% span clearance CS has the same loss with IS, and when the hub gap is 4.5% span clearance CS has almost the same loss with SS. Among all operation range, the total pressure loss of S1 increases with the increase of the hub clearance. When the hub gap is 0 (CS0), there is no leakage flow and the loss is the least. At the design point, comparing with SS, the total pressure loss coefficient of CS0 decreases 18.34%, CS2.5% decreases 8.46% and IS decreases 6.45%. It means if the cantilevered stator with 2.5% span hub clearance were adopted in the HPC, the performance would be better than the shrouded stator. However, because of the matching condition, the rotor that follows after cantilevered stator should be redesigned according to blade loading and inlet flow angle changed. The performance of cantilevered stator is impacted of various hub clearance, the loss below 25% span increases significantly with hub clearance, the maximum value of outlet flow angle deviation is 2.3 degree. The stator hub peak loading is shifted upstream toward the leading edge when hub clearance size is increased. The total pressure loss coefficient and pressure coefficient at different axial position had the function relation. When the hub clearance increases, the position of double leakage flow start backwards, in the rear part of stator the secondary flow becomes stronger leading to more mixing loss and lower total pressure.

Efficiency Variation on a 4-Stage Low Speed Research Compressor With a Redesigned Cantilevered Stator

Flow characteristics on a 4-stage low-speed research compressor with a cantilevered stator

Flow Characteristics of a Low-Solidity Cantilevered Stator Embedded in a 4-Stage Low-Speed Research Compressor

NUMERICAL INVESTIGATION OF STATOR CLOCKING EFFECTS ON THE DOWNSTREAM STATOR IN A 1.5-STAGE AXIAL TURBINE

Overall Performance and Loss Analysis of a Low-Speed Research Compressor with Different Nonaxisymmetric Tip Clearance Layouts

Hub Clearance Effect in the Design Space of the Cantilevered Stator Embedded in a 4-Stage Low-Speed Research Compressor

Different Effects of Cantilevered and Shrouded Stators on Axial Compressor Performance

Experimental and Numerical Researches in a Four-Stage Low Speed Research Compressor Facility

The Influence of Shrouded Stator Cavity Boundary Conditions on Performance of a 1.5-Stage Low-Speed Research Compressor

Three-Dimensional Compressor Blading Design Improvements in Low-Speed Model Testing

Design and Performance Analysis of a Two-Stage Transonic Low-Reaction Counter-Rotating Aspirated Fan/compressor with Inlet Counter-Swirl

Some Effects of Non-Axisymmetric Tip Clearance Layout on Axial Compressor Aerodynamics

Aerodynamic Analysis and Three-Dimensional Redesign of a Multi-Stage Axial Flow Compressor

Optimization of cantilevered stators in an industrial multistage compressor to improve efficiency

Design Optimization of the Last Stage of a 4.5-Stage Compressor Using a POD-based Hybrid Model

Experimental Study of Two-Stage Savonius Rotors with Different Gap Ratios and Phase Shift Angles

Design, Modification and Optimization of an Ultra-High-load Transonic Low-Reaction Aspirated Compressor

The Loss Mechanisms and Vortex Dynamics of Rotor Platform Step Geometries in a Low-Speed Research Compressor Stage

Characterizing Shrouded Stator Cavity Flow on the Performance of a Single-Stage Axial Transonic Compressor

Aerodynamic Design Of A Highly Loaded Supersonic Aspirated Axial Flow Compressor Stage

Redesign of a Transonic Compressor Stage Using Highly Loaded Bowed Stator