Abstract:A compact and low-power consuming fiber-optic anemometer based on single-walled carbon nanotubes (SWCNTs) coated tilted fiber Bragg grating (TFBG) is presented. TFBG as a near infrared in-fiber sensing element is able to excite a number of cladding modes and radiation modes in the fiber and effectively couple light in the core to interact with the fiber surrounding mediums. It is an ideal in-fiber device used in a fiber hot-wire anemometer (HWA) as both coupling and sensing elements to simplify the sensing head structure. The fabricated TFBG was immobilized with an SWCNT film on the fiber surface. SWCNTs, a kind of innovative nanomaterial, were utilized as light-heat conversion medium instead of traditional metallic materials, due to its excellent infrared light absorption ability and competitive thermal conductivity. When the SWCNT film strongly absorbs the light in the fiber, the sensor head can be heated and form a "hot wire". As the sensor is put into wind field, the wind will take away the heat on the sensor resulting in a temperature variation that is then accurately measured by the TFBG. Benefited from the high coupling and absorption efficiency, the heating and sensing light source was shared with only one broadband light source (BBS) without any extra pumping laser complicating the system. This not only significantly reduces power consumption, but also simplifies the whole sensing system with lower cost. In experiments, the key parameters of the sensor, such as the film thickness and the inherent angle of the TFBG, were fully investigated. It was demonstrated that, under a very low BBS input power of 9.87 mW, a 0.100 nm wavelength response can still be detected as the wind speed changed from 0 to 2 m/s. In addition, the sensitivity was found to be -0.0346 nm/(m/s) under the wind speed of 1 m/s. The proposed simple and low-power-consumption wind speed sensing system exhibits promising potential for future long-term remote monitoring and on-chip sensing in practical applications.

High Sensitivity Hot-wire Based Wind Velocity Sensor Using Co-doped Fiber and Fiber Bragg Grating for Use in Mining Applications

Temperature-compensated fiber-optic gas flow speed sensor based on the ‘Hot-wire’ principle

A High-Temperature Humidity Sensor Based on a Singlemode-Side Polished Multimode-Singlemode Fiber Structure

Fiber-Optic Anemometer Based on Bragg Grating Inscribed in Metal-Filled Microstructured Optical Fiber

A Novel Low-Power-Consumption All-Fiber-Optic Anemometer with Simple System Design

An FBG-Based Sensor Tailor-Made for Wind Pressure Monitoring of High-Speed Trains

High-Resolution Optical Fiber Temperature Sensor Based on Draw Tower Grating Array

Fiber Optic Anemometer Based on Metal Infiltrated Microstructured Optical Fiber Inscribed with Bragg Grating

Compact Optical Fiber Sensor Based on Silica Capillary Tube for Simultaneous High Temperature and Transverse Load Measurement

Fiber-Optic Hot-Wire Anemometer With Directional Response Based on Symmetry-Breaking Induced Heat Transfer Mechanism

Distributed Temperature/Vibration Fiber Optic Sensor With High Precision and Wide Bandwidth

Fiber Optic Anemometer Based on Distributed Bragg Reflector Fiber Laser

Hybrid Fiber-Optic Sensing Integrating Brillouin Optical Time-Domain Analysis and Fiber Bragg Grating for Long-Range Two-Parameter Measurement

Small-sized temperature and pressure sensors based on fiber bragg grating for oil and gas wells

Fiber-optic Sensor System for Heat-Flux Measurement

High-Temperature Sensing Based on GAWBS In Silica Single-Mode Fiber

Fiber-Optic Anemometer Based on Distributed Bragg Reflector Fiber Laser Technology

Rapid Response All-Fiber Moisture Sensor

Research and development of mine high precision wind speed sensor and temperature correction

A Fiber Optic Ultrasonic Sensing System for High Temperature Monitoring Using Optically Generated Ultrasonic Waves

Highly Sensitive and Fast Surface Temperature Sensor Based on Standard Single-Mode Fiber Using Double Heterodyne Interference Technology