Abstract:A compact and low-power consuming fiber-optic anemometer based on single-walled carbon nanotubes (SWCNTs) coated tilted fiber Bragg grating (TFBG) is presented. TFBG as a near infrared in-fiber sensing element is able to excite a number of cladding modes and radiation modes in the fiber and effectively couple light in the core to interact with the fiber surrounding mediums. It is an ideal in-fiber device used in a fiber hot-wire anemometer (HWA) as both coupling and sensing elements to simplify the sensing head structure. The fabricated TFBG was immobilized with an SWCNT film on the fiber surface. SWCNTs, a kind of innovative nanomaterial, were utilized as light-heat conversion medium instead of traditional metallic materials, due to its excellent infrared light absorption ability and competitive thermal conductivity. When the SWCNT film strongly absorbs the light in the fiber, the sensor head can be heated and form a "hot wire". As the sensor is put into wind field, the wind will take away the heat on the sensor resulting in a temperature variation that is then accurately measured by the TFBG. Benefited from the high coupling and absorption efficiency, the heating and sensing light source was shared with only one broadband light source (BBS) without any extra pumping laser complicating the system. This not only significantly reduces power consumption, but also simplifies the whole sensing system with lower cost. In experiments, the key parameters of the sensor, such as the film thickness and the inherent angle of the TFBG, were fully investigated. It was demonstrated that, under a very low BBS input power of 9.87 mW, a 0.100 nm wavelength response can still be detected as the wind speed changed from 0 to 2 m/s. In addition, the sensitivity was found to be -0.0346 nm/(m/s) under the wind speed of 1 m/s. The proposed simple and low-power-consumption wind speed sensing system exhibits promising potential for future long-term remote monitoring and on-chip sensing in practical applications.

Fiber Optic Anemometer Based on Metal Infiltrated Microstructured Optical Fiber Inscribed with Bragg Grating

Fiber-Optic Anemometer Based on Bragg Grating Inscribed in Metal-Filled Microstructured Optical Fiber

Fiber-optic anemometer based on single-walled carbon nanotube coated tilted fiber Bragg grating.

Fiber Bragg Grating Based Hot-Wire Anemometer with Enhanced Sensitivity by Fiber Surface Frosting

Photothermal anemometer based on carbon nanotube-coated highly tilted fiber Bragg grating-assisted SPR sensor

Fiber-Optic Anemometer Based on Distributed Bragg Reflector Fiber Laser Technology

Fiber Bragg Grating Anemometer and Temperature Compensation Technology

High Sensitivity Optical Fiber Thermal Anemometer Heated by Light Source

Plasmonic Fiber-Optic Photothermal Anemometers with Carbon Nanotube Coatings

Fiber Optic Anemometer Based on Distributed Bragg Reflector Fiber Laser

A Novel Low-Power-Consumption All-Fiber-Optic Anemometer with Simple System Design

Fiber anemometer for simultaneously measuring wind speed and wind direction

Fiber-Optic Anemometer With Intensity Linear Demodulation

Temperature Compensated Fiber Optic Anemometer Based on Graphene-Coated Elliptical Core Micro-Fiber Bragg Grating

Low-Power-Consumption Fiber-Optic Anemometer Based on Long-Period Grating with SWCNT Coating

Linear-response and Simple Hot-Wire Fiber-Optic Anemometer Using High-Order Cladding Mode

Real-time Fiber-Optic Anemometer Based on a Laser-Heated Few-Layer Graphene in an Aligned Graded-Index Fiber.

Research of Fiber Optic Anemometer and Wind Direction Monitoring Technology

Cascaded Fabry-Perot Interferometer-Regenerated Fiber Bragg Grating Structure for Temperature-Strain Measurement under Extreme Temperature Conditions.

Fiber Optical Temperature Compensated Anemometer Based on Dual Fabry-Perot Sensors with Sealed Cavity

Fiber-Optic Hot-Wire Anemometer With Directional Response Based on Symmetry-Breaking Induced Heat Transfer Mechanism