Abstract:Sintering behaviour of ashes from combustion of coal and biomass blends was experimentally investigated with a focus on the effect of ash preparation method. Blends of a Chinese anthracite, Jincheng coal, and two biomass materials, a wheat straw and a pine sawdust, respectively, were subjected to three different ash preparation procedures, namely, a low temperature oxygen plasma ashing device operating at ca 150 degrees C, combustion in a Muffle furnace at 815 degrees C and in a drop tube furnace at 1500 degrees C. The resulting ash samples were then subjected to the sintering temperature measurement using a pressure-drop sintering device, morphological and mineralogical characterisation using scanning electron microscope (SEM) fitted with X-ray energy dispersive spectroscopy (EDS) and X-ray diffractometry analyser (XRD), respectively. For the same coal and biomass blends but different ash preparation methods, the sintering temperatures were always the lowest for the ash samples from the plasma ashing device and the highest from drop tube furnace. SEM imaging showed that the texture of ash samples from the plasma ashing device was irregular, loose and more fibrous, indicating little interactions among the different mineral and inorganic constituents in the individual fuels. The muffle furnace and drop tube furnace ashes were denser and more uniform in shape as the mineral matter and inorganics became fused together. In addition, the drop tube furnace ashes were mostly in spherical-shape, indicating ash melting had occurred during combustion. The XRD analysis revealed that different minerals were present in the ash samples due to different ash preparation temperatures, with high temperature minerals present in the drop tube furnace ash. Biomass addition in the blends lowered the sintering temperature of corresponding ash; the higher the proportion of biomass in the blend, the lower the ash sintering temperature regardless the ashing method. At the same biomass addition ratio, the ash sintering temperature of the blend with the wheat straw addition was lower than that with the pine sawdust addition, because the wheat straw had a higher K and Cl content but lower Ca than the pine sawdust. The EDS and XRD analyses confirmed that the ashes of coal/wheat straw blends contained more K-bearing minerals, while the ashes of the coal/pine sawdust contained more Ca and K-bearing minerals. Both Ca and K-bearing minerals reacted with other minerals in the ash to form low temperature eutectics, leading to the reduction of sintering temperatures of the coal and biomass blends. However, the melting points of the K-containing minerals are higher than the Ca-containing minerals, therefore, the sintering temperatures of ash with the wheat straw addition were lower than those with the pine sawdust addition. (C) 2016 Elsevier Ltd. All rights reserved.

Effect of Binders on Performance of Corn Stalk Pellets

Influence of Binding Materials on the Main Quality Parameters of Biomass Pellets Produced from Corn Stover

Effect of minerals and binders on particulate matter emission from biomass pellets combustion

Improving the Properties of Magnetite Green Pellets with a Novel Organic Composite Binder

Pelletization property analysis of raw and torrefied corn stalks for industrial application to achieve agricultural waste conversion

Comparative investigation on fuel characteristics of different parts of corn stover considering particle size and pelletizing pressure based on macro-TGA

Effect of in-situ torrefaction and densification on the properties of pellets from rice husk and rice straw

Experiment research on utilization of particle biomass fuel in sintering process

Study of an Organic Binder of Cold-Bonded Briquettes with Two Different Iron Bearing Materials

Impact of Binder on Strength of Carbon-containing Pellet of High-iron Tailings

Recent development in production of pellet fuels from biomass and polyethylene (PE) wastes

Effect of three different binders and pellet feed on granulation behaviour of sintering mixtures

STUDY ON PREPARATION TECHNOLOGY OF HIGH-QUALITY BIOMASS FUEL PELLETS USING CARAGANA KORSHINSKII KOM. POWDER

Experimental study on the combustion characteristics of biomass pellets

Pelletization Characteristics of the Hydrothermal Pretreated Rice Straw with Added Binders

Effect of Ash Preparation Method on the Sintering Characteristics of Ashes from Combustion of Coal and Biomass Blends

Research on the hot densification mechanism of biomass wastes based on molecular dynamics simulation and components adjustment method

Characterization of binderless fuel pellets from macrophyte Azolla blended with forestry biowaste

Process Optimization of Pellet Manufacturing from Mixed Materials in Ultrasonic Vibration-Assisted Pelleting

Mechanical Strength and Combustion Properties of Biomass Pellets Prepared with Coal Tar Residue As a Binder

Effect of Binders on the Crushing Strength of Ferro-Coke