Mechanical tests, wear simulation and wear particle analysis of carbon-based nanomultilayer coatings on Ti6Al4V alloys as hip prostheses

Ji Li,Ketao Wang,Zhongli Li,J. P. Tu,Gong Jin,Jian Su,Bao Zhai

DOI: https://doi.org/10.1039/c7ra12080j

IF: 4.036

2018-01-01

RSC Advances

Abstract:Carbon-based nanomultilayer coatings were deposited on medical-grade Ti6Al4V alloy using a magnetron sputtering technique under a graded bias voltage.

What problem does this paper attempt to address?

Mechanical Tests, Wear Simulation and Wear Particle Analysis of Carbon-Based Nanomultilayer Coatings on Ti6Al4V Alloys As Hip Prostheses

Ji Li,Ketao Wang,Zhongli Li,J. P. Tu,Gong Jin,Jian Su,Bao Zhai

DOI: https://doi.org/10.1039/c7ra12080j

IF: 4.036

2018-01-01

RSC Advances

Abstract:Carbon-based nanomultilayer coatings were deposited on medical-grade Ti6Al4V alloy using a magnetron sputtering technique under a graded bias voltage. The mechanical properties of the nanomultilayer coatings were investigated by nanoindentation, Rockwell and scratch tests as well as a ball-on-disk tribometer. The biological properties related to the immunological response of the coatings were investigated by wear simulation and wear particles analysis. Wear simulation was done according to ISO 14242, wear particles were analysed according to ISO 17853, and then compared with CoCr femoral heads. The results revealed that the carbon-based nanomultilayer coatings showed a multilayer structure, with a hardness of ∼20 GPa, an elastic modulus of ∼175 GPa, an adhesion higher than 80 N, and a low average coefficient of friction of 0.1. The average gravimetric wear rate of the polyethylene cups between the coated and CoCr groups had no statistical difference (P = 0.098). The average equivalent circle diameter of particles produced in the coated group was larger than that in CoCr (P = 0.001), but the proportion of submicron particles and globular/circular particles was not significantly different between the two groups (P > 0.05). Results showed lower Co/Cr ion contamination in the coated group. Hence, the carbon-based nanomultilayer coating on Ti6Al4V has good mechanical and tribological properties, releases fewer harmful metal ions and would not cause a more intense immunological host response than a CoCr prosthesis. The newly designed a-C nanomultilayer coatings are expected to prolong the longevity of artificial hip joints.
[Five Million Wear Simulation and Particle Analysis of Carbon-Based Nano-Multilayer Coatings Titanium Alloy Femoral Head].

H R Wang,J Li,Z L Li,J P Tu,G Jin,J Su,J

DOI: https://doi.org/10.3760/cma.j.issn.0376-2491.2020.07.014

2020-01-01

Abstract:Objective: To analyze the wear debris characteristics ofcarbon-based nano- multilayer coatings on Ti(6)Al(4)V alloys and compared with the cobalt chromium molybdenum alloy (CoCrMo) femoral head to evaluate the friction and wear performance of the new coated femoral head. Methods: Three groups were set up in the wear simulation experiment according to the type of femoral head. Group A: imported Cobalt-Chromium-Molybdenum alloy femoral head (CoCrMo); group B: Titanium alloy femoral head (Ti(6)Al(4)V) with carbon-based nano-multilayer coatings; group C: domestic Cobalt-Chromium-Molybdenum alloy femoral head (CoCrMo). All heads were jointed with an ultra-high molecular weight polyethylene (UHMWPE) acetabular cup. Serum samples were collected and stored in the hip joint simulator. After the sample has been digested and diluted, it was filtered through 5 μm, 1.2 μm and 0.4 μm filters, and the filter paper was collected for testing. Scanning electron microscope (SEM) was used to randomly select regions on the filter to obtain images of wear debris. Energy dispersive X-ray spectroscopy (EDS) was used to determine the elemental type of the particle and to eliminate possible contamination. The composition and structure of the abrasive chips were measured using Fourier transform infrared spectrometer (FTIR). The parameters related to the wear debris includingparticle size, shape, number and volume were calculated. The differences in correlation parameters between the groups were compared to evaluate the friction and wear properties of the new coated joints. Results: The main component of the wear debris produced was UHMWPE, and the particle size was mostly below 1 μm. The submicron particle ratio of group B was 49.4%, which was significantly lower than that of the group A and C (75% and 60%, respectively; χ(2)=66.032, 31.754, both P<0.017). The shape was mainly round, and there was no statistical difference between the groups (χ(2)=0.590, P=0.744). The number of particles in group B was significantly less than that of group C on all filters (t=9.960, 8.019, 5.790, all P<0.01), and less than group A on the 0.4 μm filter (t=7.810, P=0.000). Conclusion: The frictional wear performance of the new carbon-based nano-multilayer coatings femoral head is significantly better than that of the domestic femoral head, and even partially exceeds the imported femoral head level, which helps to reduce the production of particles and prevent osteolysis and aseptic loosening induced by UHMWPE particles.
Electrochemical deposition multi-walled carbon nanotube coatings on the surface of Ti6Al4V alloy for enhancing its biotribological properties

Hao Cao,Panpan Tian,Jun Deng,Yanan Li,Chenchen Wang,Sheng Han,Xin Zhao

DOI: https://doi.org/10.1016/j.jmbbm.2023.105825

IF: 4.042

2023-04-05

Journal of the Mechanical Behavior of Biomedical Materials

Abstract:Ti6Al4V alloys have potential applications as bone implants. However, their poor biotribological performances affected the service life. In this work, carboxylic multi-walled carbon nanotubes (CMWNT) coatings were grafted on the surface of Ti6Al4V alloys by electrochemical deposition for enhancing the biotribological properties. The CMWNT coatings showed lower coefficient of friction and wear rates, with the reduction of wear rates of 6% in dry condition and 90% under simulated body fluid (SBF) lubrication. This result might be ascribed to the transfer of friction behavior from sliding friction to rolling friction. In addition, the tribological regularity of CMWNT coating with the frequency and load were discussed. Under dry friction, with the increase of frequency and the decrease of normal load, the COF of the CMWNT coating decreased. In SBF lubrication, the COF decreased and the wear rate increased with the increase of frequency. Moreover, the excellent anti-wear properties were observed at the below of 10 N. These findings indicate that the CMWNT coating has an excellent protective effect on titanium alloy, and has a certain application potential in the biomedical field.

engineering, biomedical,materials science, biomaterials
Increasing the wear resistance of hip prostheses components using micro-nanostructured thin layers

Liliana-Laura Badita-Voicu,Aurel Zapciu,Dorin Angelescu,Adrian-Catalin Voicu

DOI: https://doi.org/10.1177/09544062241242655

2024-04-09

Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science

Abstract:Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, Ahead of Print. Evaluation of micro-nanostructured thin layers applicability for increasing the lifetime of rehabilitation systems, mainly hip prostheses, is the aim of the present research. This because, the final objective of the complete project is to improve the quality of human prostheses using micro-nanostructured thin layers. In order to realize these researches, 0.5, 1, and 1.5 μm thick thin layers of TiN and TiO2, were deposited on substrates made of materials currently used for hip prostheses – M30NW steel and CoCr – using physical deposition methods, respectively Cathodic Arc (CA), Direct Current (DC) sputtering and High-Power Impulse Magnetron Sputtering (HiPIMS). After tribological and nanoindentation tests, the 1.5 μm thick TiN and TiO2 thin layers deposited on the steel and CoCr substrates using the DC sputtering method presented superior mechanical properties. Functional characterization of a total hip prosthesis, that have had components coated with these thin layers presented an increased resistance to fatigue wear. After comparative analysis, the main conclusion of the realized researches was that TiN layers with a thickness of 1.5 μm have an increased resistance to fatigue wear in comparison with TiO2 layers, when both are deposited by DC sputtering on M30NW steel and CoCr substrates. It was observed that 1.5 μm thick TiN layers ensures a prolongation by 15% of the lifetime of femoral heads compared to those uncoated.

engineering, mechanical
Tribological and Corrosion Behaviors of Zr-doped Graphite-Like Carbon Nanostructured Coatings on Ti6Al4V Alloy

W. Q. Bai,Y. J. Xie,L. L. Li,X. L. Wang,C. D. Gu,J. P. Tu

DOI: https://doi.org/10.1016/j.surfcoat.2017.01.038

IF: 4.865

2017-01-01

Surface and Coatings Technology

Abstract:Biomedical Ti6Al4V alloy exhibits excellent mechanical and anti-corrosion properties but poor wear resistance. In order to improve the combination performance of Ti6Al4V alloy, Zr-doped graphite-like carbon (GLC) nanomultilayer and nanocomposite coatings are deposited by magnetron sputtering. The microstructures of the coatings are characterized by transmission electron microscopy (TEM) and Raman spectroscopy. The Zr-doped GLC nanomultilayer shows low friction coefficient and wear rate at applied loads of 1N and 3N in Hank's solution. In addition, both the Zr-doped GLC nanomultilayer and nanocomposite coatings present high corrosion resistance, which results from the corrosion-resistant GLC and zirconium oxide. Compared to the Zr-doped GLC nanocomposite, the nanomultilayer is more promising in the applications under simultaneously tribological and corrosive conditions.
The Tribological Performance of Surface Treated Ti6A14V as Sliding Against Si3N4 Ball and 316L Stainless Steel Cylinder

W. H. Kao,Y. L. Su,J. H. Horng,H. C. Huang

DOI: https://doi.org/10.1007/s11665-016-2384-x

IF: 2.3

2016-10-11

Journal of Materials Engineering and Performance

Abstract:Closed field unbalanced magnetron sputtering was used to deposit diamond-like carbon (Ti-C:H) coatings on Ti6Al4V alloy and gas nitrided Ti6Al4V alloy. Four different specimens were prepared, namely untreated Ti6Al4V alloy (Ti6Al4V), gas nitrided Ti6Al4V alloy (N-Ti6Al4V), Ti-C:H-coated Ti6Al4V alloy (Ti-C:H/Ti6Al4V) and Ti-C:H-coated gas nitrided Ti6Al4V alloy (Ti-C:H/N-Ti6Al4V). The tribological properties of the four specimens were evaluated using a reciprocating wear tester sliding against a Si3N4 ball (point contact mode) and 316L stainless steel cylinder (line contact mode). The wear tests were performed in a 0.89 wt.% NaCl solution. The results showed that the nitriding treatment increased the surface roughness and hardness of the Ti6Al4V alloy and improved the wear resistance as a result. In addition, the Ti-C:H coating also improved the tribological performance of Ti6Al4V. For example, compared to the untreated Ti6Al4V sample, the Ti-C:H coating reduced the wear depth and friction coefficient by 340 times and 10 times, respectively, in the point contact wear mode, and 151 times and 9 times, respectively, in the line contact wear mode. It is thus inferred that diamond-like carbon coatings are of significant benefit in extending the service life of artificial biomedical implants.

materials science, multidisciplinary
Multilayered TiAlN films on Ti6Al4V alloy for biomedical applications by closed field unbalanced magnetron sputter ion plating process

Peiyun Yi,Linfa Peng,Jiaqiang Huang

DOI: https://doi.org/10.1016/j.msec.2015.10.071

Abstract:Ti6Al4V alloy has been widely used as a suitable material for surgical implants such as artificial hip joints. In this study, a series of multilayered gradient TiAlN coatings were deposited on Ti6Al4V substrate using closed field unbalanced magnetron sputter ion plating (CFUBMSIP) process. Taguchi design of experiment approach was used to reveal the influence of depositing parameters to the film composition and performance of TiAlN coatings. The phase structure and chemical composition of the TiAlN films were characterized by X-ray diffractometry (XRD) and X-ray photoelectron spectroscopy (XPS). Mechanical properties, including hardness, Young's modulus, friction coefficient, wear rate and adhesion strength were systematically evaluated. Potentiodynamic tests were conducted to evaluate the corrosion resistance of the coated samples in Ringer's solution at 37°C to simulate human body environment. Comprehensive performance of TiAlN films was evaluated by assigning different weight according to the application environment. S8, deposited by Ti target current of 8A, Al target current of 6A, bias voltage of -60V and nitrogen content with OEM (optical emission monitor) value of 45%, was found to achieve best performance in orthogonal experiments. Depositing parameters of S8 might be practically applied for commercialization of surgical implants.
Mechanical Properties and in Vitro and in Vivo Biocompatibility of A-C/a-c:Ti Nanomultilayer Films on Ti6Al4V Alloy As Medical Implants.

Lingling Li,Wenqi Bai,Xiuli Wang,Changdong Gu,Gong Jin,Jiangping Tu

DOI: https://doi.org/10.1021/acsami.7b02552

IF: 9.5

2017-01-01

ACS Applied Materials & Interfaces

Abstract:Hydrogen-free a-C/a-C:Ti nanomultilayer films are deposited on medical Ti6Al4V alloy using a closed field unbalanced magnetron sputtering under graded bias voltage. The mechanical and tribological properties of the nanomultilayer films are performed on the nanoindentor, Rockwell and scratch tests, and ball-on-disk tribometer. The biological properties are evaluated by cell cytotoxicity, genotoxicity, subchronic systemic toxicity and implant. The hard a-C/a-C:Ti nanomultilayer films on medical alloy exhibit high adhesion strength and excellent tribological properties in both ambient air and Hank's solution. Biocompatibility results reveal the film no cytotoxity, no genotoxicity, no subchronic systemic toxicity and no contraindications in implant systems. Because of excellent mechanical properties and biosafety, the carbon-based films on medical alloy unveils a prospective application in medical implants.
Microstructure and Properties of Monolayer Ta and Multilayer Ta/Ti/Zr/Ta Coatings Deposited on Biomedical Ti-6Al-4V Alloy by Magnetron Sputtering

Suli Zhao,Shuguang Liu,Yongjie Xue,Ning Li,Kuixue Xu,Weiwei Qiu,Xuexian Li,Jinbo Wang,Qian Wu,Chunbao Shi

DOI: https://doi.org/10.3390/coatings13071234

IF: 3.236

2023-07-12

Coatings

Abstract:Two types of coatings, i.e., monolayer Ta and multilayer Ta/Ti/Zr/Ta coatings, were deposited on biomedical Ti6Al4V (TC4) alloy by magnetron sputtering to improve its performance. To evaluate the effect of the two coatings on the alloy properties, the microstructure, composition, mechanical and tribological properties, in vitro biocompatibility, and corrosion resistance were investigated. The results showed that α-Ta exists in the monolayer Ta coating, while α-Ta and β-Ta phases coexist in the multilayer Ta/Ti/Zr/Ta coating. The multilayer Ta/Ti/Zr/Ta coating possessed the highest hardness and the monolayer Ta coating had the lowest friction coefficient compared to the Ti6Al4V alloy. The friction and wear tests revealed that the anti-wear performance of the Ta coating is the best, followed by that of the Ta/Ti/Zr/Ta coating, while the anti-wear performance of TC4 alloy is relatively poor in comparison with the Ta and Ta/Ti/Zr/Ta coatings. The wear resistance of the multilayer Ta/Ti/Zr/Ta coating under low normal load is better than that under high load normal load. Finally, the in vitro and electrochemical corrosion tests showed that the Ta coating modification provides better biocompatibility and corrosion resistance than those of the uncoated Ti6Al4V alloy.

materials science, multidisciplinary,physics, applied, coatings & films
Microstructure, mechanical and tribological properties Of A-C/A-C:Ti nanomultilayer film

Jianbin Cai,Xiuli Wang,W. Q. Bai,D. H. Wang,Changdong Gu,Jiangping Tu

DOI: https://doi.org/10.1016/j.surfcoat.2013.05.042

IF: 4.865

2013-01-01

Surface and Coatings Technology

Abstract:An a-C/a-C: Ti multilayer film with a bilayer period of 40 nm was deposited on medical Ti6Al4V alloy using a closed field unbalanced magnetron sputtering. The microstructure and chemical composition of the multilayer film were investigated by transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy. The mechanical and tribological properties were evaluated from nanoindentation, Rockwell and scratch tests, and ball-on-disk tribometer. Nanoindentation tests showed that the hardness of the multilayer film reached 25 GPa with good toughness. Due to the interface effect, the adhesion strength of the nanomultilayer was significantly improved. In humid air without lubrication, the a-C/a-C: Ti nanomultilayer film had a low friction coefficient of 0.080 and wear rate of 1.95×10−16 m3 N−1 m−1 at a load of 10 N. While in Hanks' solution, the film exhibited lower friction coefficient of 0.074 and wear rate of 4.25×10−17 m3 N−1 m−1.
Evaluation of tribological and biological properties of Ti6Al4V coated with Si3N4/ND nanoparticles for orthopedic applications: a comprehensive analysis

Mohammad Mahdi Esmaeili,Nahid Hassanzadeh Nemati,Morteza Daliri Joupari

DOI: https://doi.org/10.1088/1748-605X/ad4e82

2024-06-13

Abstract:In this study, the biocompatibility and tribological properties of Ti6Al4V coated with silicon nitride (Si3N4)/nanodiamond using the electrophoretic deposition method were investigated. Suspensions of various aqueous and alcoholic solutions were prepared in the presence of CTAB and SDS dispersers. The most stable suspension system for the electrophoresis process was selected (aqueous media/ SDS disperser). Four different voltages (20, 30, 40 and 50 V) were applied to study the effect of voltage on the coating property. One could find that processing with 40 V obtained the best coating. The nano-composite coating was characterized using scanning electron microscopy equipped with energy dispersive spectroscopy, mapping analysis and x-ray diffraction after the coating process. The samples were then subjected to two nanoindentation and nano-scratching tests to evaluate their tribological properties. Biocompatibility was assessed in an ex vivo environment using two cell culture tests to evaluate survival and cellular adhesion. The results showed that the hardness and modulus elasticity of the coated sample increased from 85 to 124 GPa and 1.14-3.55 GPa, respectively, compared to the non-coated sample. Additionally, the MTT test results indicated that cellular survival and proliferation of MG63 cells increased from 86% for the non-coated sample to 92% for the Ti6Al4V/Si3N4/ND sample. These findings have implications for orthopedic implant applications.
Study of TiCuN/ZrN multilayer coatings with adjustable combination properties deposited on TiCu alloy

Xiyue Zhang,Yanhui Zhao,Wenwei Gao,Ling Ren,Ke Yang

DOI: https://doi.org/10.1016/j.vacuum.2022.111202

IF: 4

2022-08-01

Vacuum

Abstract:Orthopedic metal implant materials such as titanium alloy may face the problem of friction wear during long-term implantation. TiCu alloy has been proved to have excellent mechanical properties, biofunctionability and biocompatibility. In order to further improve its wear resistance, a multilayer coating composed of high hardness TiCuN and ZrN were deposited on the surface of TiCu by axial magnetic field enhanced pulsed bias arc ion plating (AMFE-AIP) system. Then, the corresponding relationship among the modulation period (Λ), the microstructure of the TiCuN/ZrN multi-layers and the influence properties were analyzed. The results showed that in the multi-layers, there existed a “Cu nail/bridge” structure which was biased perpendicular to the direction of the film. With the decrease of the Λ, the maximum stress on the coating surface during the sliding process was decreased, the adhesion, wear resistance of the film and the release of Cu ions from the film were gradually increased, which resulted in the improvement of anti-bacteria and cell proliferation promotion properties. This study indicated that the TiCuN/ZrN multilayer coating is promised to be a new kind of biofunctionalized coating with properties that can be regulated on demand for adapting various implant environment of titanium alloy implants.

materials science, multidisciplinary,physics, applied
Effects of Ti Content on Microstructure, Mechanical and Tribological Properties of Ti-doped Amorphous Carbon Multilayer Films

W. Q. Bai,L. L. Li,X. L. Wang,F. F. He,D. G. Liu,G. Jin,J. P. Tu

DOI: https://doi.org/10.1016/j.surfcoat.2015.02.024

2015-01-01

Abstract:Ti-doped amorphous carbon multilayer films with different Ti content are deposited on medical Ti6Al4V alloy using a closed field unbalanced magnetron sputtering. The microstructure and chemical composition are characterized by high resolution transmission electron microscopy (HRTEM), atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). The mechanical and tribological properties are evaluated by nanoindentation, Rockwell and scratch tests and ball-on-disk tribometer. The Ti content has a significant influence on the microstructure, mechanical and tribological properties of Ti doped a-C multilayer films. TiC nanocrystallites started to form in the a-C:Ti layer when the Ti target current density was above 2.58mAcm−2 during multilayer deposition process. Among these multilayers, the film deposited with a Ti target current density of 4.13mAcm−2 displays high hardness (25.2GPa), high critical load (about 80N), and low friction coefficient and wear rate in ambient air and in Hank's solution.
In Vitro and in Vivo Investigations of A-C/a-c:Ti Nanomultilayer Coated Ti6Al4V Alloy As Artificial Femoral Head.

Ji Li,Zhongli Li,Jiangping Tu,Gong Jin,Lingling Li,Ketao Wang,Haoran Wang

DOI: https://doi.org/10.1016/j.msec.2019.02.022

2019-01-01

Materials Science and Engineering C

Abstract:Hydrogen-free a-C/a-C:Ti nanomultilayer (a-C NM) films were deposited on medical Ti6Al4V by the magnetron sputtering technique under bias-graded voltage. Cell tests and implantations were performed for the a-C NM films coated Ti6Al4V with the uncoated Ti6Al4V as the control. The canine total hip arthroplasty (THA) surgeries were conducted for 12 dogs using the coated femoral heads, with the CoCr heads as the control. Results of cell tests showed that the coated Ti6Al4V had no cytotoxicity, and there was no statistical difference of the cell attachment rates between the coated and uncoated sample (P = 0.091). No significant difference of the tissue response around the coated and uncoated implants were observed after the intramuscular (P = 0.679) and intraosseous implantations (P = 0.122). After two years of successful canine THA, the polyethylene wear particles isolated from periprosthetic soft tissue showed similar sizes, shapes and counts in the two groups (all of the P values >0.05). The retrieved femoral heads showed slightly change of the surface roughness, but no statistical differences between groups (P = 0.696). However, the systemic metal ion analysis indicated that the content of Co and Cr ions released in the coated group (Co: 0.71 ± 0.06 μg/L, Cr: 0.52 ± 0.05 μg/L) were significant lower than that in the control (Co: 1.98 ± 0.16 μg/L, Cr: 1.17 ± 0.19 μg/L) (both P < 0.005). Histological analysis of the periprosthetic tissue in CoCr group showed a severer histiocyte response than that in the coated group (P = 0.029). The head-taper interfaces showed galvanic corrosion attack in the CoCr group, but not in the coated Ti6Al4V group. Therefore, the a-C NM films coated Ti6Al4V exhibited good biocompatibility as an implant material. Compared with the CoCr, the coated Ti6Al4V femoral head could provide comparable in vivo wear properties, release less harmful metal ions and reduce the inflammatory response in periprosthetic tissue, which may help to prolong the longevity of prostheses.
Wear performance of Ti-6Al-4 V titanium alloy through nano-doped lubricants

Hamza E. L. Etri,Anil Kumar Singla,Mehmet Tayyip Özdemir,Mehmet Erdi Korkmaz,Recep Demirsöz,Munish Kumar Gupta,J. B. Krolczyk,Nimel Sworna Ross

DOI: https://doi.org/10.1007/s43452-023-00685-9

IF: 4.042

2023-05-16

Archives of Civil and Mechanical Engineering

Abstract:Titanium and its alloys are widely utilized in the biomedical sector, they still exhibit poor tribological properties and low wear resistance when employed against even weaker substances. The poor hardness, instability, high coefficient of friction, low load-carrying capacity, and insufficient resistance to not only abrasive but also adhesive wear are further disadvantages of titanium alloys. The focus of this investigation is on the tribological performance of Ti-6Al-4 V alloy in contact with WC carbide abrasive balls when subjected to nanodoped cooling and lubrication conditions. Tribological experiments were executed on Ti-6Al-4 V flat samples using a ball-on-flat tribometer in dry hybrid graphene/boron nitride combination nanoparticles (MQL, nano-3), nanographene with MQL (nano-1), and boron nitride with MQL (nano-2) conditions. After that, the most significant tribological characteristics were investigated, including volume loss, friction coefficient, wear rate, and micrographic structures. The outcomes also demonstrated that the hybrid nanoparticle situation experienced the least amount of volume loss.

engineering, mechanical,materials science, multidisciplinary, civil
Microstructure and properties of monolayer, bilayer and multilayer Ta2O5-based coatings on biomedical Ti-6Al-4V alloy by magnetron sputtering

Zeliang Ding,Quan Zhou,Yi Wang,Ziyu Ding,Yinghong Tang,Quanguo He

DOI: https://doi.org/10.1016/j.ceramint.2020.08.230

IF: 5.532

2021-01-01

Ceramics International

Abstract:In recent years, tantalum pentoxide (Ta2O5) ceramic coating has attracted considerable attention in the modification of implants due to its excellent biocompatibility, high corrosion resistance, and good wear resistance. However, the poor adhesion to the substrate degrades its performance and may become a significant obstacle to its clinical application. In the paper, Ta2O5 monolayer, Ta2O5/Ti bilayer, and Ta2O5/Ta2O5-Ti/Ti multilayer coatings were prepared on the Ti-6Al-4V alloy by magnetron sputtering. The microstructure, chemical composition, residual thermal stress, adhesion strength, mechanical properties, tribological behaviors, and corrosion resistance of the coatings were investigated and compared. The results showed that these deposited coatings were composed of an amorphous nano-Ta2O5 phase, and their surfaces were smooth, dense, and homogeneous without any cracks. Ta2O5/Ta2O5-Ti/Ti coatings exhibited lower thermal residual stress than that of the Ta2O5 and Ta2O5/Ti coatings, which could be attributed to the decrease of the coefficient of thermal expansion (CTE) mismatch between the Ta2O5 film and Ti-6Al-4V substrate due to the introduction of the Ta2O5-Ti/Ti double-interlayer. Moreover, Ta2O5/Ta2O5-Ti/Ti coating was significantly superior to Ta2O5 and Ta2O5/Ti coatings in the adhesion strength, mechanical properties, and wear resistance. These Ta2O5-based coatings can provide excellent corrosion protection for Ti-6Al-4V alloy in simulated body fluids (SBF). The Ta2O5 monolayer coating samples showed the best corrosion resistance, mainly due to its thick out-layer Ta2O5 film. These experimental results provide a feasible way to improve the performances of Ta2O5 coating on Ti-6Al-4V alloy.

materials science, ceramics
Comparison of wear properties of Ti6Al4V fabricated by wrought and electron beam melting processes in simulated body fluids

Dingding Xiang,Xipeng Tan,Zhenhua Liao,Jinmei He,Zhenjun Zhang,Weiqiang Liu,Chengcheng Wang,Beng Tor Shu

DOI: https://doi.org/10.1108/RPJ-09-2018-0256

2020-01-01

Rapid Prototyping Journal

Abstract:Purpose This paper aims to study the wear properties of electron beam melted Ti6Al4V (EBM-Ti6Al4V) in simulated body fluids for orthopedic implant biomedical applications compared with wrought Ti6Al4V (Wr-Ti6Al4V). Design/methodology/approach Wear properties of EBM-Ti6Al4V compared with Wr-Ti6Al4V against ZrO2 and Al2O3 have been investigated under dry friction and the 25 Wt.% newborn calf serum (NCS) lubricated condition using a ball-on-disc apparatus reciprocating motion. The microstructure, composition and hardness of the samples were characterized using scanning electron microscopy (SEM), x-ray diffraction and a hardness tester, respectively. The contact angles with 25 Wt.% NCS were measured by a contact angle apparatus. The wear parameters, wear 2D and 3D morphology were obtained using a 3D white light interferometer and SEM. Findings EBM-Ti6Al4V yields a higher contact angle than the Wr-Ti6Al4V with the 25 Wt.% NCS. EBM-Ti6Al4V couplings exhibit lower coefficients of friction compared with the Wr-Ti6Al4V couplings under both conditions. There is only a slight difference in the wear resistance between the Wr-Ti6Al4V and EBM-Ti6Al4V alloys. Both Wr-Ti6Al4V and EBM-Ti6Al4V suffer from similar friction and wear mechanisms, i.e. adhesive and abrasive wear in dry friction, while abrasive wear under the NCS condition. The wear depth and wear volume of the ZrO2 couplings are lower than those of the Al2O3 couplings under both conditions. Originality/value This paper helps to establish baseline bio-tribological data of additively manufactured Ti6Al4V by electron beam melting in simulated body fluids for orthopedic applications, which will promote the application of additive manufacturing in producing the orthopedic implant.
Tribological Properties of Ti6Al4V Alloy Composite Texture Fabricated by Ultrasonic Strengthening Grinding and Laser Processing

Jinrui Xiao,Yiteng Zhang,Bin Hu,Xiaochu Liu,Zhongwei Liang,Zhuan Zhao

DOI: https://doi.org/10.3390/ma16010355

IF: 3.4

2022-12-31

Materials

Abstract:The Ti6Al4V alloy has been widely used in aerospace equipment and medical devices. However, the poor wear resistance of the Ti6Al4V alloy hinders its further engineering application. In this study, the ultrasonic strengthening grinding process (USGP) and laser texturing process were employed to enhance the wear resistance of Ti6Al4V alloy. The frictional behavior of all samples was determined via a ball-on-disc friction and wear tester under dry conditions. The worn surface morphology, cross-sectional hardness, surface roughness, and microstructure were analyzed. The results demonstrated that the USGP induced high hardness, high dislocation density, and grain refinement, as well as improvements in the wear resistance of Ti6Al4V. Moreover, laser texture could enhance the capacity to capture wear debris and reduce wear probability. When combining the USGP and laser texturing process for the surface treatment of Ti6Al4V alloy, the lowest and most stable friction coefficients were obtained, as well as the best wear resistance. Compared to the polished sample, the steady stage friction coefficient of the sample treated by USGP and laser texturing process was remarkably decreased by 58%. This work demonstrates that combining the USGP and laser texturing process could be a promising solution for improving the wear resistance properties of Ti6Al4V alloy, which makes it more suitable for various engineering applications.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Wear studies on ZrO2-filled PEEK as coating bearing materials for artificial cervical discs of Ti6Al4V

Jian Song,Yuhong Liu,Zhenhua Liao,Song Wang,Rajnesh Tyagi,Weiqiang Liu

DOI: https://doi.org/10.1016/j.msec.2016.08.007

2016-12-01

Abstract:Polyetheretherketone (PEEK) and its composite coatings are believed to be the potential candidates' bio-implant materials. However, these coatings have not yet been used on the surface of titanium-based orthopedics and joint products and very few investigations on the tribological characteristics could be found in the published literature till date. In this study, the wettabilities, composition and micro-hardness were characterized using contact angle measurement, scanning electron microscopy (SEM) and hardness tester. The tribological tests were conducted using a ball-on-disc contact pair under 25% newborn calf serum (NCS) lubricated condition. For comparison, bare Ti6Al4V was studied. The obtained results revealed that those PEEK/ZrO2 composite coatings could improve the tribological properties of Ti6Al4V significantly. Adhesive wear and mild abrasive wear might be the dominant wear and failure mechanisms for PEEK/ZrO2 composite coatings in NCS lubricated condition. After comprehensive evaluation in the present study, 5wt.% ZrO2 nanoparticles filled PEEK coating displayed the optimum tribological characteristics and could be taken as a potential candidate for the bearing material of artificial cervical disc.
Surface topography, corrosion and microhardness of nitrogen-diffusion-hardened titanium alloy

R Venugopalan,M A George,J J Weimer,L C Lucas

DOI: https://doi.org/10.1016/s0142-9612(99)00079-4

IF: 14

Biomaterials

Abstract:Mechanical-electrochemical interactions accelerate corrosion in mixed-metal modular hip prostheses. These interactions can be reduced by improving the modular component machining tolerances or by improving the resistance of the components to scratch or fretting damage. Wrought cobalt-alloy (CoCrMo) is known to have better tribological properties compared to the titanium alloy (Ti64). Thus, improving the tribological properties of this mixed-metal interface should center around improving the tribological properties of the Ti64 alloy. This study used scanning probe microscopy (contact, tapping and phase contrast mode), scanning electron microscopy, corrosion testing, and microhardness testing to determine the effect of a nitrogen-diffusion hardening process on the surface morphology, electrochemistry and surface hardness of the Ti64 alloy. The nitrogen-diffusion-hardened titanium alloy samples (N-Ti64) had a more pronounced grain structure, more nodular surface, and significantly (P<0.01) higher mean roughness values than the control-Ti64 samples. The N-Ti64 samples also exhibited at least equivalent corrosion behavior and a definite increase in surface hardness compared to the control Ti64 samples. The equivalent corrosion behavior and improved surface hardness indicate the potential for N-Ti64 samples to resist similar and mixed-metal scratch and fretting damage. The use of N-Ti64 as opposed to control-Ti64 may therefore reduce the occurrence of mechanical-electrochemical degradation in mixed-metal modular total hip prostheses.

Mechanical tests, wear simulation and wear particle analysis of carbon-based nanomultilayer coatings on Ti<sub>6</sub>Al<sub>4</sub>V alloys as hip prostheses

Mechanical Tests, Wear Simulation and Wear Particle Analysis of Carbon-Based Nanomultilayer Coatings on Ti6Al4V Alloys As Hip Prostheses

[Five Million Wear Simulation and Particle Analysis of Carbon-Based Nano-Multilayer Coatings Titanium Alloy Femoral Head].

Electrochemical deposition multi-walled carbon nanotube coatings on the surface of Ti6Al4V alloy for enhancing its biotribological properties

Increasing the wear resistance of hip prostheses components using micro-nanostructured thin layers

Tribological and Corrosion Behaviors of Zr-doped Graphite-Like Carbon Nanostructured Coatings on Ti6Al4V Alloy

The Tribological Performance of Surface Treated Ti6A14V as Sliding Against Si3N4 Ball and 316L Stainless Steel Cylinder

Multilayered TiAlN films on Ti6Al4V alloy for biomedical applications by closed field unbalanced magnetron sputter ion plating process

Mechanical Properties and in Vitro and in Vivo Biocompatibility of A-C/a-c:Ti Nanomultilayer Films on Ti6Al4V Alloy As Medical Implants.

Microstructure and Properties of Monolayer Ta and Multilayer Ta/Ti/Zr/Ta Coatings Deposited on Biomedical Ti-6Al-4V Alloy by Magnetron Sputtering

Microstructure, mechanical and tribological properties Of A-C/A-C:Ti nanomultilayer film

Evaluation of tribological and biological properties of Ti6Al4V coated with Si3N4/ND nanoparticles for orthopedic applications: a comprehensive analysis

Study of TiCuN/ZrN multilayer coatings with adjustable combination properties deposited on TiCu alloy

Effects of Ti Content on Microstructure, Mechanical and Tribological Properties of Ti-doped Amorphous Carbon Multilayer Films

In Vitro and in Vivo Investigations of A-C/a-c:Ti Nanomultilayer Coated Ti6Al4V Alloy As Artificial Femoral Head.

Wear performance of Ti-6Al-4 V titanium alloy through nano-doped lubricants

Microstructure and properties of monolayer, bilayer and multilayer Ta2O5-based coatings on biomedical Ti-6Al-4V alloy by magnetron sputtering

Comparison of wear properties of Ti6Al4V fabricated by wrought and electron beam melting processes in simulated body fluids

Tribological Properties of Ti6Al4V Alloy Composite Texture Fabricated by Ultrasonic Strengthening Grinding and Laser Processing

Wear studies on ZrO2-filled PEEK as coating bearing materials for artificial cervical discs of Ti6Al4V

Surface topography, corrosion and microhardness of nitrogen-diffusion-hardened titanium alloy