The All-fiber Graphene Modulator

Feng Zhou,Xiaofeng Jin

DOI: https://doi.org/10.1364/noma.2017.nom4c.4

2017-01-01

Abstract:The all-fiber graphene modulator working as either an electro-absorption (EA) or phase modulator is proposed. Both electro-absorption and phase fiber modulators exhibit excellent performances such as small footprint and good integrated compatibility.

What problem does this paper attempt to address?

A Graphene-Based All-Fiber Electro-Absorption Modulator

Feng Zhou,Xiaofeng Jin,Ran Hao,Xianmin Zhang,Hao Chi,Shilie Zheng

DOI: https://doi.org/10.1007/s12596-016-0330-9

IF: 2.1

2016-01-01

Journal of Optics

Abstract:An all-fiber structured electro-absorption (EA) modulator based on graphene is proposed. The graphene is directly attached to the core of the fiber to ensure the coupling efficiency. Mode analysis is used to reveal the light modulation mechanism under the anisotropic graphene modeling, which is merely conducted in previous studies. Compared with conventional semiconductor EA modulators, it exhibits an excellent performance with the advantages such as small footprint (50.2 μm), small voltage swing (0.2 V), and broad operation bandwidth. In addition, the proposed modulator features simple structure, low optical propagation and coupling loss, and good integrated compatibility as the fiber modulator. All these edges prospect the great potentiality in future high-speed optic fiber communications, optical signal processing, and all-fiber systems.
Active Graphene-Microfiber Modulator

D. Popa,Z. Zhao,U. Sassi,Z. Yang,Y. Xu,L. Tong,A. C. Ferrari

DOI: https://doi.org/10.1109/cleoe-eqec.2017.8087697

2017-01-01

Abstract:Active modulation of light with large optical bandwidths (∼100 nm [1]) is required in photonic devices, such as modulators for fiber communications [1] and saturable absorbers for ultrafast pulse generation [2,3]. Present modulators use expensive materials, (e.g. LiNbO 3 [4], III-V semiconductors [5], and Ge on silicon-on-insulator (SOI) [6]), and are limited by narrowband operation (∼20 nm for quantum-confined Stark effect devices [7], or <0.1 nm for resonators [8]), or high loss (∼80% in Si Mach-Zehnder modulators [9]). Single layer graphene (SLG) can be transferred and integrated on a variety of waveguide systems (e.g. a-Si, Si 3 N 4 ) while offering a full-band operation [10]. In all-fiber platforms, including ultrafast lasers [2,3], high coupling losses (∼60% from fiber to SOI waveguide [6]) are driving development of fiber-based modulators. Ref. 3 reported an electrically controllable all-fiber optical modulator with a SLG transistor on a side-polished fiber. However, its gating speed was limited to∼300 Hz [11] due to the low mobility of the ionic liquid used for gating. Here, we report a graphene-microfiber modulator by integrating a microfiber onto a graphene (SLG plated) capacitor (GC). By varying the microfiber size and length we control the light interaction with the biased SLG plates. This can be used for active control of ultrafast laser working in continuous wave, Q-switching and mode-locking operations.
The All-Fiber Electro-Absorption Modulator Based on Quadri-Layer Graphene

Feng Zhou,Xiaofeng Jin

DOI: https://doi.org/10.1109/icocn.2016.7875778

2016-01-01

Abstract:An all-fiber structured electro-absorption (EA) modulator based on quadri-layer graphene is proposed. The quadri-layer graphene is directly built into the core of the fiber to ensure the coupling efficiency. Mode analysis is used to reveal the light modulation mechanism under the anisotropic graphene modeling, which is merely conducted in previous studies. Compared with conventional semiconductor EA modulators, it exhibits an excellent performance with the advantages such as small footprint (12.9 μm), high modulation depth (0.233 dB/μm), small voltage swing (0.2 V), low energy consumption and broad operation bandwidth. In addition, the proposed modulator features simple structure, low optical propagation and coupling loss, and good integrated compatibility as the fiber modulator. All these edges prospect the great potentiality in future high-speed optic fiber communications, optical signal processing, and all-fiber systems.
Graphene-cladding-microfiber All-Optical Modulator

Limin Tong,Wei Li,Bigeng Chen

DOI: https://doi.org/10.1364/acpc.2013.af3a.1

2013-01-01

Abstract:By coating a few-layer-graphene film on the surface of a subwavelength-diameter microfiber that is tapered down from a standard optical fiber, we demonstrated an all-optical ultrafast modulator operating around 1.5-um wavelength with response time of about 2 ps. Article not available.
Graphene-Enhanced Fiber Modulator with Small Footprint and Good Integrated Compatibility

Feng Zhou,Xiaofeng Jin

DOI: https://doi.org/10.1364/acpc.2016.af2a.121

2016-01-01

Abstract:We proposed a graphene-based fiber phase modulator. The results confirmed the graphene layer has greatly enhanced the light-matter interaction. A pi phase modulator with arm length of 127 mu m is numerically demonstrated.
A Graphene-Enhanced Fiber-Optic Phase Modulator with Large Linear Dynamic Range

Feng Zhou,Ran Hao,Xiao-Feng Jin,Xian-Min Zhang,Er-Ping Li

DOI: https://doi.org/10.1109/lpt.2014.2336660

IF: 2.6

2014-01-01

IEEE Photonics Technology Letters

Abstract:We propose a graphene-based modulator integrated into currently used communication fibers. The graphene is directly built into the core of the fiber to ensure the coupling efficiency. The fiber is deliberately side-polished to enhance the light-graphene interaction. The two-dimensional model analysis method and three-dimensional finite difference time domain method are used to rigorously disclose the light modulation mechanism under the anisotropic graphene modeling, which is merely conducted in previous studies. Based on such a structure, a phase modulator with an arm length of 127 μm is numerically demonstrated with enhanced modulation efficiency. A quasi-linear relation between the phase change and chemical potential of graphene is found theoretically for the first time, providing a large linear dynamic range to control the phase of optical modulation.
Graphene decorated microfiber for ultrafast optical modulation.

Shaoliang Yu,Chao Meng,Bigeng Chen,Hongqing Wang,Xiaoqin Wu,Weitao Liu,Shangjian Zhang,Yong Liu,Yikai Su,Limin Tong

DOI: https://doi.org/10.1364/cleo_si.2015.sm3l.5

IF: 3.8

2015-01-01

Optics Express

Abstract:We demonstrate ultrafast optical modulation using a single 1-μm-diameter graphene-decorated microfiber, which is fabricated with a convenient and controllable evanescent-field-induced deposition method. Benefitting from the significantly enhanced light-graphene interaction of the subwavelength transvers dimension of the microfiber and accumulation of the saturable absorption of the piled graphene flakes, the microfiber shows nonlinear saturable absorption with a peak power threshold down to 1.75 W (60 MW/cm<sup>2</sup>), with a measured response time of about 3.5 ps.
Ultrafast All-Optical Graphene Modulator.

Wei Li,Bigeng Chen,Chao Meng,Wei Fang,Yao Xiao,Xiyuan Li,Zhifang Hu,Yingxin Xu,Limin Tong,Hongqing Wang,Weitao Liu,Jiming Bao,Y. Ron Shen

DOI: https://doi.org/10.1021/nl404356t

IF: 10.8

2014-01-01

Nano Letters

Abstract:Graphene is an optical material of unusual characteristics because of its linearly dispersive conduction and valence bands and the strong interband transitions. It allows broadband light-matter interactions with ultrafast responses and can be readily pasted to surfaces of functional structures for photonic and optoelectronic applications. Recently, graphene-based optical modulators have been demonstrated with electrical tuning of the Fermi level of graphene. Their operation bandwidth, however, was limited to about 1 GHz by the response of the driving electrical circuit. Clearly, this can be improved by an all-optical approach. Here, we show that a graphene-clad microfiber all-optical modulator can achieve a modulation depth of 38% and a response time of ∼ 2.2 ps, limited only by the intrinsic carrier relaxation time of graphene. This modulator is compatible with current high-speed fiber-optic communication networks and may open the door to meet future demand of ultrafast optical signal processing.
Active Control of Absorption in a Hybrid Graphene-Microfiber Modulator

Z. Zhao,D. Popa,U. Sassi,Z. Yang,Y. Xu,L. Tong,A. C. Ferrari

DOI: https://doi.org/10.1364/cleo_at.2017.af1b.5

2017-01-01

Abstract:We report a hybrid graphene-microfiber odulator with low insertion loss ~0.4dB, and active, ~6.7%, control of absorption. This can be used for active control of ultrafast laser working in continuous wave, Q-switching and mode-locking operations.
Graphene-activated Microfibers and Nanofibers for Ultrafast Optical Modulation

Limin Tong

DOI: https://doi.org/10.1364/oedi.2014.oth4a.1

2014-01-01

Abstract:Based on optical microfibers or nanofibers coated or doped with graphene flakes, we demonstrate ultrafast optical modulation around 1.5-um wavelength with response time down to 2.2 ps and pulse energy down to 0.25 pJ/pulse. Article not available.
Ultra-Compact Graphene-Embedded Optical Phase Modulators

Ran Hao,Jia-Min Jin,Er-Ping Li

DOI: https://doi.org/10.1109/ursigass.2014.6929409

2014-01-01

Abstract:Optical modulator is the key components in the optical communication, yet the low modulation efficiency limits its development. A high efficiency, ultra-compact optical modulator is proposed which the electro-refraction effect has been significantly enhanced. The different kinds of graphene schemes are compared and discussed. A graphene embedded Mach-Zender modulator has been theoretically demonstrated with the advantage of ultra-compact footprint (4×30 μm2), high modulation efficiency (20 V·μm), fast modulation speed and large extinction ratio (35dB). Our results may promote various on-chip active components, boosting the utilization of graphene in optical applications.
An All-Optical Modulator Based on a Stereo Graphene–microfiber Structure

Jin-Hui Chen,Bi-Cai Zheng,Guang-Hao Shao,Shi-Jun Ge,Fei Xu,Yan-Qing Lu

DOI: https://doi.org/10.1038/lsa.2015.133

2015-01-01

Light Science & Applications

Abstract:An in-line, all-optical fiber modulator based on a stereo graphene–microfiber structure (GMF) utilizing the lab-on-rod technique was demonstrated in this study. Owing to its unique spring-like geometry, an ultra-long GMF interaction can be achieved, and a modulation depth of ∼7.5 dB (∼2.5 dB) and a modulation efficiency of ∼0.2 dB mW−1 (∼0.07 dB mW−1) were demonstrated for two polarization states. The modulation depth and modulation efficiency are more than one order of magnitude larger than those of other graphene–microfiber hybrid all-optical modulators, although at the cost of a higher insertion loss. By further optimizing the transferring and cleaning process, the upper limit of the modulation depth is mainly determined by the loss from the intrinsic absorption, which depends on the light–graphene interaction. Then, the modulator can quickly switch between the on-state and the off-state with a theoretically maximized modulation depth of tens of decibels. This modulator is compatible with the current fiber-optic communication systems and may be applied in the near future to meet the impending need for ultrafast optical signal processing. A polarization-sensitive all-optical fiber modulator based on a graphene–microfiber structure has been demonstrated by researchers in China. All-optical modulators with high modulation speeds, sufficient modulation depth and wide optical bandwidth are needed to realize ultrafast optical signal processing. Now, Fei Xu and co-workers at Nanjing University have fabricated an all-optical fiber modulator whose modulation depth and efficiency are more than ten times greater than previous all-optical modulators based on graphene and microfibers. These properties originate from its very long interaction length resulting from its spring-like geometry. The researchers consider that even better performance can be achieved by using higher quality graphene and improving the transfer and wrapping of the graphene in the fabrication process. Since the modulator is compatible with existing fiber-optic communication systems, it may find rapid application for ultrafast optical signal processing.
All-optical Graphene Modulator Based on Optical Kerr Phase Shift

Shaoliang Yu,Xiaoqin Wu,Keren Chen,Bigeng Chen,Xin Guo,Daoxin Dai,Limin Tong,Weitao Liu,Yan Shen

DOI: https://doi.org/10.1364/optica.3.000541

IF: 10.4

2016-01-01

Optica

Abstract:Graphene-based optical modulators have recently attracted much attention because of their characteristic ultrafast and broadband response. Their modulation depth (MD) and overall transmittance (OT), however, are often limited by optical loss arising from interband transitions. We report here an all-optical, all-fiber optical modulator with a Mach–Zehnder interferometer structure that has significantly higher MD and OT than graphene-based loss modulators. It is based on the idea of converting optically induced phase modulation in the graphene-cladded arm of the interferometer to intensity modulation at the output of the interferometer. The device has the potential to be integrable into a photonic system in real applications.
Theoretical Investigation of a Broadband All-Optical Graphene-Microfiber Modulator

Xiaoying He,Min Xu,Xiangchao Zhang

DOI: https://doi.org/10.1364/josab.33.002588

2016-01-01

Journal of the Optical Society of America B

Abstract:Graphene pasted on the surface of a nanostructure, e.g., microfiber, enables such graphene-based devices to have excellent photonic and electronic properties. In this paper, an all-optical modulator based on a polymer-supported bilayer graphene film half-wrapped on the surface of the microfiber has been theoretically presented and discussed to make the best use of its ultrawide bandwidth. According to the theoretical analyses on the graphene-microfiber modulator, 100 Gbit/s 8 channel synchronous modulation has been realized with similar to 14.88 and similar to 14.80 dB modulation depth, respectively, for two polarized modes. The channel wavelength of such modulator covers C, L, and U bands. To ensure the extinction ratio of 16 channel synchronous modulation to be larger than 5 dB, the bilayer graphene-microfiber interaction length of the modular should be greater than 93.06 mu m and the diameter of the microfiber be around 1.8 mu m. Under this condition, it also has a tolerance on signal deterioration, as it could effectively decrease the noise of "0" signal. (C) 2016 Optical Society of America
A Graphene-Integrated 3D Microfiber Coil For All-Optical Signal Processing

Jin-Hui Chen,Fei Xu

DOI: https://doi.org/10.1364/FIO.2015.FW6C.3

2015-01-01

Abstract:We experimentally demonstrated an all-optical fiber modulator with spring-like geometry by wrapping a microfiber on a rod pretreated with a graphene sheet. A modulation depth of 7.5 dB and 2.5 dB were demonstrated for two non-degenerate polarization states.
Gate‐Tunable Graphene Optical Modulator on Fiber Tip: Design and Demonstration

Zi-xuan Ding,Hao-tian Xu,Yi-feng Xiong,Kang-hu Zhou,Ye Chen,Yan-qing Lu,Fei Xu

DOI: https://doi.org/10.1002/adom.202201724

IF: 9

2022-01-01

Advanced Optical Materials

Abstract:A fiber‐end‐face‐integrated electrically tunable optical modulator based on graphene field‐effect transistor and the fabrication technique are proposed and demonstrated. The all‐fiber device features a scheme of compactness and high integration when applied to fiber optical system, as well as a low insertion loss since spatial coupling of light is avoided. A reflecting structure is used and the electro‐optic modulator shows vivid modulation when gate voltage gets tuned, with maximum optical reflectance modulation depth over 1% in demonstration. To the best of the authors’ knowledge, it is the first time to build an all‐solid gate‐control modulator directly on fiber facet. The fabrication methods introduce workflows of silicon‐on‐insulator processing into the optical fiber end‐face micromachining domain which can be applied to more comprehensive configurations, broadening the path of fiber‐end‐face integrated device.
Recent Developments in Graphene-Based Optical Modulators

Ran Hao,J. M. Jin,E. P. Li

DOI: https://doi.org/10.1007/s12200-014-0424-4

2014-01-01

Abstract:Graphene has shown promising perspectives in optical active components due to the large active-control of its permittivity-variation. This paper systematically reviews the recent developments of graphene-based optical modulators, including material property, single-layer , multi-layer , few-layer graphene-based modulators and corresponding figure-of-merits.The results showed graphene is an excellent material for enhancing silicons weak modulation capability after it is integrated into the silicon platform, showing significant influence on optical interconnects in future integrated optoelectronic circuits.
All optical graphene modulator based on optical Kerr phase shift

Shaoliang Yu,Xiaoqin Wu,Keren Chen,Bigeng Chen,Xin Guo,Daoxin Dai,Limin Tong,Weitao Liu,Y. Ron Shen

DOI: https://doi.org/10.1364/OPTICA.3.000541

2016-01-01

Abstract:Graphene-based optical modulators have recently attracted much attention because of their characteristic ultrafast and broadband response. Their modulation depth (MD) and overall transmittance (OT), however, are often limited by optical loss arising from interband transitions. We report here an all-optical, all-fiber optical modulator with a Mach–Zehnder interferometer structure that has significantly higher MD and OT than graphene-based loss modulators. It is based on the idea of converting optically induced phase modulation in the graphene-cladded arm of the interferometer to intensity modulation at the output of the interferometer. The device has the potential to be integrable into a photonic system in real applications.
Graphene-based all-optical modulators

Chuyu Zhong,Junying Li,Hongtao Lin

DOI: https://doi.org/10.1007/s12200-020-1020-4

2020-06-01

Frontiers of Optoelectronics

Abstract:All-optical devices, which are utilized to process optical signals without electro-optical conversion, play an essential role in the next generation ultrafast, ultralow power-consumption optical information processing systems. To satisfy the performance requirement, nonlinear optical materials that are associated with fast response, high nonlinearity, broad wavelength operation, low optical loss, low fabrication cost, and integration compatibility with optical components are required. Graphene is a promising candidate, particularly considering its electrically or optically tunable optical properties, ultrafast large nonlinearity, and high integration compatibility with various nanostructures. Thus far, three all-optical modulation systems utilize graphene, namely free-space modulators, fiber-based modulators, and on-chip modulators. This paper aims to provide a broad view of state-of-the-art researches on the graphene-based all-optical modulation systems. The performances of different devices are reviewed and compared to present a comprehensive analysis and perspective of graphene-based all-optical modulation devices.

engineering, electrical & electronic
Low insert loss bilayer graphene compact twin-core optical fiber intensity modulator

Hexuan Wang,Jian Tang,Ming Chen,Jie Xu,Shiliang Qu,Yu Cheng,Libo Yuan

DOI: https://doi.org/10.1016/j.ijleo.2022.169117

IF: 3.1

2022-06-01

Optik

Abstract:A compact modulator with high bandwidth and extinction ratio is proposed to achieve light intensity modulation by adjusting the phase of the light transmitted in the fiber. The better modulation effect is achieved by placing two-lamellae of graphene embedded in Al 2 O 3 and PVB on a side-polished microfiber of MZM. Finite element software is used to analyze the modulation effect, the function of the chemical potential of graphene and the effective refractive of modulator is established. Extinction ratios of port 1 and port 2 can reach 11.54 dB and 11.88 dB in 92 μ m by substituting the function into simulation. While achieving a more compact modulation structure, the insert loss is also controlled below 0.0193 dB/ μ m . For the first time, the contact width between bilayer graphene and the electrode is increased by placing the electrode at the head and end of the modulator, which leads to 132.427 GHz modulation bandwidth. And the modulator does not require the excess support structure necessarily benefit from the placement of the electrode. The proposed phase-shift light intensity modulator has high extinction ratio and large bandwidth, which leads to great transmission capacity and modulate speed.

optics

The All-fiber Graphene Modulator

A Graphene-Based All-Fiber Electro-Absorption Modulator

Active Graphene-Microfiber Modulator

The All-Fiber Electro-Absorption Modulator Based on Quadri-Layer Graphene

Graphene-cladding-microfiber All-Optical Modulator

Graphene-Enhanced Fiber Modulator with Small Footprint and Good Integrated Compatibility

A Graphene-Enhanced Fiber-Optic Phase Modulator with Large Linear Dynamic Range

Graphene decorated microfiber for ultrafast optical modulation.

Ultrafast All-Optical Graphene Modulator.

Active Control of Absorption in a Hybrid Graphene-Microfiber Modulator

Graphene-activated Microfibers and Nanofibers for Ultrafast Optical Modulation

Ultra-Compact Graphene-Embedded Optical Phase Modulators

An All-Optical Modulator Based on a Stereo Graphene–microfiber Structure

All-optical Graphene Modulator Based on Optical Kerr Phase Shift

Theoretical Investigation of a Broadband All-Optical Graphene-Microfiber Modulator

A Graphene-Integrated 3D Microfiber Coil For All-Optical Signal Processing

Gate‐Tunable Graphene Optical Modulator on Fiber Tip: Design and Demonstration

Recent Developments in Graphene-Based Optical Modulators

All optical graphene modulator based on optical Kerr phase shift

Graphene-based all-optical modulators

Low insert loss bilayer graphene compact twin-core optical fiber intensity modulator