Abstract:A new design concept of highly-loaded axial flow compressor by applying boundary layer suction and 3D blade technique was proposed in this paper. The basic idea of this design concept was that low reaction was adopted as while as increasing the rotor's geometry turning angle, so that the boundary layer separation of a rotor could be eliminated and the rotor was kept working in high efficiency. This design concept would greatly increase the stator's geometry turning angle, so boundary layer suction on stator cascades was adopted in order to restrain the boundary layer separation. In some situations, 3D blade technique was also applied in order to control the boundary layer separation more efficiently. The advantages of the above design concept were: the compressor's pressure ratio was increased remarkably; boundary layer suction was only adopted in stator cascades so as to reduce the complexity of boundary layer suction structure.The key techniques of the new design concept were also explained in this paper. In order to increase the compressor's pressure ratio, the geometry turning angle of rotor was increased greatly, and the rotor inlet was prewhirled to reduce the rotor's reaction so as to restrain the rotor's boundary separation. Boundary layer suction was carried out in the stator cascades (mainly on suction side), hub and shroud in order to control the flow separation. 3D blade technique could be adopted if necessary.The limitation of the application of this design concept was also pointed out through the analysis of the Mach number at rotor inlet, the prewhirl angle of rotor, the work distribution along span wise and the control method of stator separation.Numerical simulation was carried out on a single low-reaction compressor stage with IGV in order to demonstrate the new design concept. By using boundary layer suction and 3D blade technique, the energy loss in stator cascades was greatly reduced and the whole stage's isentropic efficiency was about 90%. The low-reaction stage's aerodynamic load was double than conventional design. The boundary layer separation could be effectively controlled by proper combination of boundary layer suction and bowed or twisted blade. The numerical result proved that the new design concept was feasible and had a wide application area.

ICOPE-15-C053 New Technologies Approach to Design Impulse High Pressure Turbine Stages

An Aerodynamic Design and Numerical Investigation of Transonic Centrifugal Compressor Stage

Aerodynamic Analysis and Three-Dimensional Redesign of a Multi-Stage Axial Flow Compressor

NUMERICAL STUDY ON THE FLOW FIELD ANALYSIS AND OPTIMIZATION OF TURBINE IN SUPERCRITICAL COMPRESSED AIR ENERGY STORAGE

Study on Aerodynamic Optimization Design Process of Multistage Axial Turbine

Study On Aerodynamic Redesign Of A High Pressure Ratio Centrifugal Compressor

Three-Dimensional Aerodynamic Optimization of a Multi-Stage Axial Compressor

Numerical Simulation and Aerodynamic Optimization of Two-Stage Axial High-Pressure Turbine Blades

CFD simulation and aerodynamic optimization of two-stage axial high-pressure turbine blades

Aerodynamic Preliminary Design Optimization of Ten-stage High Pressure Compressor

Three-dimensional Optimized Design of an Air-cooled Turbine Stage

Steam turbine high-pressure reaction stages; new 3D vortices breakdown and airfoil optimization method

Fluid Dynamic Efficiency Optimization of Steam Turbine Stages Considering Leakage Influences and Inter-stage Reciprocal Interferences

A New Design Concept of Highly-Loaded Axial Flow Compressor by Applying Boundary Layer Suction and 3d Blade Technique

A Novel Airfoil Design Method and its Application to the Optimization Design of a 3-Stage Transonic Compressor

The Design and Performance Analysis of a Highly-Loaded Turbine

Aerodynamic Optimisation of a Low-Pressure Multistage Turbine Using the Response-Surface Method

Aerodynamic Design by Jointly Applying S2 Flow Surface Calculation and Modern Optimization Methods on Multistage Axial Turbine

Experimental Investigation on Off-Design Performance of a Small-Scale Two-Stage Counter-Rotating Impulse Turbine

A Cfd Approach to Fluid Dynamic Optimum Design of Steam Turbine Stages with Stator and Rotor Blades