Sensing the Earth Crustal Deformation with Nano-strain Resolution Fiber-optic Sensors

Zuyuan He,Qingwen Liu,Tomochika Tokunaga

DOI: https://doi.org/10.1364/e2.2014.etu4a.4

2014-01-01

Abstract:Recent development of fiber optic strain sensors with nano-strain-resolution and large measurement range for sensing the Earth crustal deformation is reviewed. In field experiment, tide induced crustal deformation and the seismic wave were successfully recorded.

What problem does this paper attempt to address?

Highly Sensitive and Fast Response Strain Sensor Based on Evanescently Coupled Micro/nanofibers

Wen Yu,Ni Yao,Jing Pan,Wei Fang,Xiong Li,Limin Tong,Lei Zhang

DOI: https://doi.org/10.29026/oea.2022.210101

IF: 8.9329

2022-01-01

Opto-Electronic Advances

Abstract:Flexible strain sensors play an important role in electronic skins, wearable medical devices, and advanced robots. Herein, a highly sensitive and fast response optical strain sensor with two evanescently coupled optical micro/nanofibers (MNFs) embedded in a polydimethylsiloxane (PDMS) film is proposed. The strain sensor exhibits a gauge factor as high as 64.5 for strain ≤ 0.5% and a strain resolution of 0.0012% which corresponds to elongation of 120 nm on a 1 cm long device. As a proof-of-concept, highly sensitive fingertip pulse measurement is realized. The properties of fast temporal frequency response up to 30 kHz and a pressure sensitivity of 102 kPa −1 enable the sensor for sound detection. Such versatile sensor could be of great use in physiological signal monitoring, voice recognition and micro-displacement detection.
Vertically Distributed Sensing of Deformation Using Fiber Optic Sensing

Cheng-Cheng Zhang,Bin Shi,Kai Gu,Su-Ping Liu,Jing-Hong Wu,Song Zhang,Lei Zhang,Hong-Tao Jiang,Guang-Qing Wei

DOI: https://doi.org/10.1029/2018gl080428

IF: 5.2

2018-01-01

Geophysical Research Letters

Abstract:Vertical deformation can be revealed by various techniques such as precise leveling, satellite imagery, and extensometry. Despite considerable effort, recording detailed subsurface deformation using traditional extensometers remains challenging when attempting to detect localized deformation. Here we introduce distributed fiber optic sensing based on Brillouin scattering as a geophysical exploration method for imaging distributed profiles of vertical deformation. By examining fiber optic cable-soil interaction we found a threshold in confining pressure to achieve a strong cable-soil coupling, thus validating data collected from a borehole-embedded fiber optic cable deployed in Shengze, southern Yangtze Delta, China. Clear-cut strain profiles acquired from November 2014 to December 2016 allowed us to pinpoint where compaction or rebound was actively occurring and examine strain responses at various locations along the entire cable length. We suggest that distributed fiber optic sensing can complement with extensometry and remote sensing techniques for improved monitoring of vertical deformation. Plain Language Summary Recording detailed subsurface deformation using traditional methods (e.g., extensometers) is sometimes difficult due to limited measuring points. This dilemma may be overcome by using the emerging distributed fiber optic sensing technology, which transforms common telecommunication fiber optic cables into sensors capable of making distributed strain measurements. We report the use of this technology for monitoring distributions of vertical deformation resulting from groundwater abstraction in Shengze, southern Yangtze Delta, China. An evaluation of the performance of a borehole-embedded fiber optic cable helps us to validate the in situ strain data. The advantage of using this technology for vertical deformation sensing is the ability to locate any strata undergoing compaction or rebound and look at strain responses at any depth of interest. Moreover, recording subsurface changes in this fashion may also be useful in other geophysical and engineering applications that require refined monitoring of the media.
Large detection range and high strain sensitivity fiber SPR sensor based on wave structure

Yong Wei,Puxi Ren,Chunlan Liu,Tianci Jiang,Chunbiao Liu,Chen Shi,Yixiong Tang,Ziqiang Zhang,Zhihai Liu

DOI: https://doi.org/10.1364/OE.521801

2024-04-22

Abstract:To achieve a fiber strain sensor with a large detection range and high sensitivity, this paper proposes a wave structured fiber SPR strain sensor. When subjected to axial strain, the wave structured fiber is stretched axially, increasing the stretchability of the sensor and achieving a large detection range strain sensing. Meanwhile, axial strain reduces the longitudinal amplitude of the fiber wave structure, effectively changing the total reflection angle of the transmitted beam at the peak and valley (SPR incidence angle) to achieve high sensitivity SPR strain sensing. The experiment indicates that the strain detection range of the sensor can reach 0-1800µε, with a maximum strain sensitivity of 36.25pm/µε. The wave structured fiber SPR strain sensor designed in this article provides a new approach to improve the range and sensitivity of strain detection.
Fiber-optic Wireless Sensor Network Using Ultra-Weak Fiber Bragg Gratings for Vertical Subsurface Deformation Monitoring

Liu Su-Ping,Shi Bin,Gu Kai,Zhang Cheng-Cheng,He Jian-Hui,Wu Jing-Hong,Wei Guang-Qing

DOI: https://doi.org/10.1007/s11069-021-04932-1

IF: 3.158

2021-01-01

Natural Hazards

Abstract:The determination of subsurface deformation is critical to understanding the subsurface dynamic processes, but most of conventional monitoring methods still have challenges in remotely obtaining detailed data. Herein, a novel fiber-optic wireless sensor network using the ultra-weak fiber Bragg gratings technique was proposed. It allows real-time remote capture of subsurface deformation along the fiber-optic cables. Such a fiber-optic measurement system was employed in a borehole to a depth of 340 m in Cangzhou, China. Strain profiles were measured monthly with a spatial resolution of 5 m and strain resolution of 1 µε, and the development of all strata deformation in the aquifer systems was calculated from January 2019 to December 2019. It turns out that the subsidence rate in this area is approximate 9 mm/a, which agrees well with the result of extensometer measurements. The significant strata compaction in the second aquifer and the third aquitard rapidly increased from May 2019 to July 2019, which could be attributed to the decline in groundwater. It is concluded that the fiber-optic wireless sensor network accurately captures subsurface deformation development and helps to better elucidate the subsurface deformation mechanism and provide solutions for the prevention and mitigation.
High-Sensitivity Microfiber Strain and Force Sensors

Wei Li,Zhifang Hu,Xiyuan Li,Wei Fang,Xin Guo,Limin Tong,Jingyi Lou

DOI: https://doi.org/10.1016/j.optcom.2013.09.072

IF: 2.4

2014-01-01

Optics Communications

Abstract:A microfiber biconically tapered from a standard optical fiber shows obvious sinusoidal oscillatory transmission spectrum due to the multimode interference, with evident blue-shifted peak wavelength when applying an axial force. Based on this force-induced spectral shift, here we experimentally demonstrate compact microfiber strain and force sensors with low optical power and high sensitivity. With a 1.5-μW probing light, measured sensitivity of a 2.5-μm-diameter microfiber for the strain and elongation sensing are 4.84pm/με and 404pm/μm respectively, with a force detection limit down to 50μN.
Distributed and multimodal strain sensing performance of flexible hydrogel functional optical fibers

Yan Zhuang,Kai Gong,Jianhui Sun,Zishi Jiang,Yiqian Li,Peng Li

DOI: https://doi.org/10.1039/d4nj03055a

IF: 3.3

2024-10-10

New Journal of Chemistry

Abstract:Traditional silica-based optical fiber strain sensors are suffering from limited range of strain detection, mismatched mechanical performance, and complicated sensing structures for practical applications involving complex strain patterns and large strain measurement. To solve this problem, the development of novel flexible optical fiber strain sensors with distributed and multimodal strain sensing performance is critical but challenging. In this work, the flexible hydrogel optical fiber with a step-index core/cladding structure was successfully designed and fabricated using a simple thermal polymerization method, madding of calcium alginate and polyacrylamide. The resulting flexible fiber exhibits a large stretch deformation capacity and good optical transmission property, while also enabling effective and reversible strain response. Significantly, a flexible hydrogel functional fiber was further constructed by doping quantum dots with different fluorescent emission wavelengths in different positions. By exploiting a combination of emission wavelength encoding and transmission loss, flexible hydrogel functional optical fibers can distinguish and recognize the locations, magnitudes, and modes (stretch or bend) of mechanical deformation through a single wavelength of visible light (365 nm) excitation. The ultra-large dynamic range (0~120%) of axial strain and bending deformation (10~80 degree) can be effectively detected. This work offers a versatile solution to develop promising stretchable and distributed fiber strain sensors.

chemistry, multidisciplinary
Toward Distributed Fiber‐Optic Sensing of Subsurface Deformation: A Theoretical Quantification of Ground‐Borehole‐Cable Interaction

Cheng-Cheng Zhang,Bin Shi,Hong-Hu Zhu,Bao-Jun Wang,Guang-Qing Wei

DOI: https://doi.org/10.1029/2019jb018878

2020-01-01

Abstract:Fiber-optic sensing is emerging as a superior means for distributed strain sensing of the subsurface. The ability of an embedded fiber-optic cable to capture accurate strain profiles depends on the degree of rigid mechanical coupling between the ground and the cable. However, a current challenge in this field is to determine the actual level of ground deformation from strain signatures sensed by the cable deployed in the subsurface; addressing this issue has been hampered by the lack of suitable theoretical methods. Here we propose a two-step ground-cable coupling evaluation procedure, whereby we develop analytical formulations to quantify the interaction and interface shear transfer of a ground-borehole-cable system. We constrain key model parameters using a data set acquired with a fiber optics-instrumented borehole for monitoring groundwater-related sediment compaction. Extensive parametric analyses reveal that increasing the backfill modulus and cable gauge length or decreasing the borehole radius and cable stiffness can improve the quality of strain transferred to the cable from the ground; the effect of ground properties is comparably insignificant. Further, we develop design charts and tables at designated transfer thresholds to facilitate the development and field deployment of fiber sensing elements. Taken together, the theoretical quantification of ground-cable coupling should improve the state-of-the-art performance of distributed fiber-optic strain sensing for subsurface ground movements detection and monitoring.
Monitoring Flexure Behavior of Compacted Clay Beam Using High-Resolution Distributed Fiber Optic Strain Sensors

Hao-Jie Li,Hong-Hu Zhu,Chun-Xin Zhang,Narala Gangadhara Reddy,Ankit Garg,Hai-Ying Wu

DOI: https://doi.org/10.1520/gtj20200331

2022-01-01

Geotechnical Testing Journal

Abstract:Understanding the mechanical characteristics of clayey soil is critical to estimate the stability of clay-related geotechnical engineering works. However, the distributed information of the internal deformation of clay is hard to capture through traditional methods. In this paper, a set of four-point bending tests were performed on a compacted clay beam instrumented with fiber optic strain sensors to investigate the flexure and cracking behaviors. The optical frequency domain reflectometry technique with high spatial resolution and precision was employed to establish a distributed strain sensing (DSS) system in this study. The results show that the DSS system exhibits a high accuracy in the collection of the clay deformation in terms of compression, tension, and cracking. The comparison of the internal strain profiles with the observation of particle image velocimetry analysis system verifies the feasibility of fiber optic sensing technology in the quantitative assessment of clay deformation. The performance of fiber optic sensors in the rebound deformation and creep deformation monitoring was preliminarily issued in the study. In addition, the progressive failure on the fiber-soil interface was analytically studied to evaluate the deformation compatibility between the fiber and surrounding clayed soil. The conclusions drawn in this paper can help to guide the state interpretation of clayey soil instrumented with fiber optic sensors.
Role of the interface between distributed fibre optic strain sensor and soil in ground deformation measurement

Cheng-Cheng Zhang,Hong-Hu Zhu,Bin Shi

DOI: https://doi.org/10.1038/srep36469

IF: 4.6

2016-01-01

Scientific Reports

Abstract:Recently the distributed fibre optic strain sensing (DFOSS) technique has been applied to monitor deformations of various earth structures. However, the reliability of soil deformation measurements remains unclear. Here we present an integrated DFOSS- and photogrammetry-based test study on the deformation behaviour of a soil foundation model to highlight the role of strain sensing fibre–soil interface in DFOSS-based geotechnical monitoring. Then we investigate how the fibre–soil interfacial behaviour is influenced by environmental changes, and how the strain distribution along the fibre evolves during progressive interface failure. We observe that the fibre–soil interfacial bond is tightened and the measurement range of the fibre is extended under high densities or low water contents of soil. The plastic zone gradually occupies the whole fibre length when the soil deformation accumulates. Consequently, we derive a theoretical model to simulate the fibre–soil interfacial behaviour throughout the progressive failure process, which accords well with the experimental results. On this basis, we further propose that the reliability of measured strain can be determined by estimating the stress state of the fibre–soil interface. These findings may have important implications for interpreting and evaluating fibre optic strain measurements, and implementing reliable DFOSS-based geotechnical instrumentation.
High Precision Temperature Insensitive Strain Sensor Based on Fiber-Optic Delay

Ning Yang,Jun Su,Zhiqiang Fan,Qi Qiu

DOI: https://doi.org/10.3390/s17051005

IF: 3.9

2017-01-01

Sensors

Abstract:A fiber-optic delay based strain sensor with high precision and temperature insensitivity was reported, which works on detecting the delay induced by strain instead of spectrum. In order to analyze the working principle of this sensor, the elastic property of fiber-optic delay was theoretically researched and the elastic coefficient was measured as 3.78 ps/km·με. In this sensor, an extra reference path was introduced to simplify the measurement of delay and resist the cross-effect of environmental temperature. Utilizing an optical fiber stretcher driven by piezoelectric ceramics, the performance of this strain sensor was tested. The experimental results demonstrate that temperature fluctuations contribute little to the strain error and that the calculated strain sensitivity is as high as 4.75 με in the range of 350 με. As a result, this strain sensor is proved to be feasible and practical, which is appropriate for strain measurement in a simple and economical way. Furthermore, on basis of this sensor, the quasi-distributed measurement could be also easily realized by wavelength division multiplexing and wavelength addressing for long-distance structure health and security monitoring.
Temperature Insensitive Distributed Wide-dynamic-range Strain Sensing based on Polarization-Maintaining Photonic Crystal Fiber

Zhenyuan Xu,Youfu Geng,Xiaojian Zhu,Jing Lu,duo yi,Yu Du,Jiaqi Wang,Xueming Hong,Xuejin Li

DOI: https://doi.org/10.1088/1361-6463/ad40bb

2024-04-20

Journal of Physics D Applied Physics

Abstract:In this paper, a temperature insensitive wide-dynamic-range distributed strain sensor with centimeter-level spatial resolution based on optical frequency domain reflection technology is proposed. It adopts a polarization-maintaining photonic crystal fiber (PMPCF) as the sensing fiber, and experimental results demonstrate that its temperature sensitivity is much smaller than that of the standard polarization-maintaining fiber(PMF). Benefited from the specially designed cross-correlation algorithm, the sensor achieves the maximum measurable strain reaches 7000 με with spatial resolution of 1.66 cm. This provides a new approach to address current issues with special fiber sensors, such as single-point sensing and low spatial resolution, which shows great significance for structural health monitoring of buildings, bridges and tunnels with urgent requirement of large dynamic range.

physics, applied
Microanchored borehole fiber optics allows strain profiling of the shallow subsurface

Cheng-Cheng Zhang,Bin Shi,Song Zhang,Kai Gu,Su-Ping Liu,Xu-Long Gong,Guang-Qing Wei

DOI: https://doi.org/10.1038/s41598-021-88526-8

IF: 4.6

2021-04-28

Scientific Reports

Abstract:Abstract Vertical deformation profiles of subterranean geological formations are conventionally measured by borehole extensometry. Distributed strain sensing (DSS) paired with fiber-optic cables installed in the ground opens up possibilities for acquiring high-resolution static and quasistatic strain profiles of deforming strata, but it is currently limited by reduced data quality due to complicated patterns of interaction between the buried cables and their surroundings, especially in upper soil layers under low confining pressures. Extending recent DSS studies, we present an improved approach using microanchored fiber-optic cables—designed to optimize ground-to-cable coupling at the near surface—for strain determination along entire lengths of vertical boreholes. We proposed a novel criterion for soil–cable coupling evaluation based on the geotechnical bearing capacity theory. We applied this enhanced methodology to monitor groundwater-related vertical motions in both laboratory and field experiments. Corroborating extensometer recordings, acquired simultaneously, validated fiber optically determined displacements, suggesting microanchored DSS as an improved means for detecting and monitoring shallow subsurface strain profiles.

multidisciplinary sciences
Hollow-porous fiber-shaped strain sensor with multiple wrinkle-crack microstructure for strain visualization and wind monitoring

Xinxin Zhao,Hao Guo,Peng Ding,Wei Zhai,Chuntai Liu,Changyu Shen,Kun Dai

DOI: https://doi.org/10.1016/j.nanoen.2023.108197

IF: 17.6

2023-01-12

Nano Energy

Abstract:Flexible strain sensor shows great development prospects in medical treatment, human-machine interface and environmental monitoring fields due to their great flexibility, ductility, skin-mountability and excellent sensing abilities. Nevertheless, the inherent contradictions between sensitivity and sensing range limit their further development as high-performance strain sensors. To solve this challenge, a two step pre-stretching strategy was proposed in this paper. Wrinkle and crack structures on carbon nanotubes (CNTs) conductive layer were integrated into a thermoplastic polyurethane (TPU) fiber with hollow-porous structure. Benefiting from the synergistic structure of the conductive layer, the fiber-shaped strain sensor synchronously possesses a wide sensing range (up to 530% strain), high sensitivity (gauge factor, GF up to 57.2), low detection limit (0.5% strain) and satisfactory sensing stability and durability. The sensing mechanism was proposed based on the development of the conductive network and the wrinkle and crack microstructures in detail. Moreover, strain-dependent visualization of the sensor under ultraviolet (UV) light was realized on the basis of the good UV-shielding property of the CNTs layer and the exposure of fluorescent agent (FA) in TPU fiber during the crack propagation process. This fiber-shaped strain sensor was demonstrated for human bio-signals acquisition as well as the monitoring of wind direction, showing its broad application prospects as next generation flexible strain sensor.

materials science, multidisciplinary,chemistry, physical,physics, applied,nanoscience & nanotechnology
Advanced Fiber Optic Sensing for Cryogenic Simultaneous Temperature and Strain Measurement

Jialong Han,Taolue Yang,Xingzhe Wang

DOI: https://doi.org/10.1109/tim.2024.3440393

IF: 5.6

2024-08-25

IEEE Transactions on Instrumentation and Measurement

Abstract:Accurately measuring complex temperature and strain fields is crucial in engineering, but it is particularly challenging in volatile, low-temperature environments due to the significant temperature dependence of sensor parameters. This article introduces a sophisticated model using distributed fiber optic sensing (DFOS) technique for simultaneous measurement of nonuniform fields of temperature and strain in low-temperature settings, overcoming the inherent temperature sensitivity of the sensors through Rayleigh scattering and integration with an optical frequency-domain reflectometer (OFDR). Our experimental setup involves the utilization of a single optical fiber securely affixed to the specimen's surface in an arc-based geometrical configuration. We suggest a simultaneous and decoupling approach to rigorously segregate the harmonic components of temperature and strain fields, effectively addressing the temperature sensitivity. Extensive experiments cover uniform combined temperature and strain load scenarios, as well as scenarios involving gradient temperature-strain loads. Both arc-based and full circle-based configurations yielded consistent, robust results, demonstrating their efficiency in accurate decoupling. This highlights the DFOS's suitability for engineering applications needing accurate, concurrent temperature and strain measurements.

engineering, electrical & electronic,instruments & instrumentation
Quantitative Evaluation of Optical Fiber/Soil Interfacial Behavior and Its Implications for Sensing Fiber Selection

Cheng-Cheng Zhang,Hong-Hu Zhu,Jun-Kuan She,Dan Zhang,Bin Shi

DOI: https://doi.org/10.1109/jsen.2014.2386881

IF: 4.3

2014-01-01

IEEE Sensors Journal

Abstract:An adequate understanding of the interface between optical fibers and geomaterials is a prerequisite for applying distributed optical fiber sensor systems to strain monitoring in geoengineering. This contribution reports a quantitative investigation of the fiber/soil interfacial behavior regarding the influence of fiber types and normal pressures. A simplified model describing the progressive failure of a fiber/soil interface was briefly illustrated. Results of a series of pullout tests on three different soil-embedded optical fibers under various normal pressures were interpreted by this model, through which the fiber/soil interfacial behaviors were quantified. The results showed that the mechanical properties of the three fiber/soil interfaces were similar. Optical microscopic images indicated that the soil particles and the fibers were merely loosely contacted. This led to the formation of a fiber/soil interface susceptible to the normal pressure: 1) the interfacial bond was tightened and 2) the deformation measurement range was widened under high normal pressures. Moreover, the criterion for selecting a strain sensing fiber for geoengineering applications was discussed in terms of interfacial bond, deformation measurement range, ratio of peak to residual interfacial shear strength, Young's modulus of fiber, and so forth. An assessment of the three fibers reveals that, for ground deformation measurement, each fiber has its own advantages as well as limitations. In field or laboratory applications, a combination of different types of fibers may obtain the best measurement results.
Strain integration-based soil shear displacement measurement using high-resolution strain sensing technology

Han Wu,Hong-Hu Zhu,Cheng-Cheng Zhang,Gu-Yu Zhou,Bao Zhu,Wei Zhang,Mohammad Azarafza

DOI: https://doi.org/10.1016/j.measurement.2020.108210

IF: 5.6

2020-12-01

Measurement

Abstract:<p>The distributed fiber optic sensing technology has emerged as a promising tool for monitoring soil shear deformation. However, the question remains whether the strain measurements obtained by the soil-embedded optical fiber cables are reliable due to cable-soil slippage. In this paper, a direct shear model test was conducted in laboratory to characterize the cable-soil deformation compatibility considering different anchorage conditions. The optical frequency domain reflectometer was employed to measure cable strains. The measurements were compared with those from the particle image velocity technique. When the strain sensing cable couples well with soil, the cable elongation exhibits a linear relationship with the soil shear displacement. A strain integration method is then proposed to convert strain measurements into shear displacements. Furthermore, the effect of block and tube anchors on the cable-soil coupling behavior is investigated. The conclusions drawn in this study provide a reference for establishing new geotechnical deformation monitoring systems.</p>

engineering, multidisciplinary,instruments & instrumentation
Superior Piezoresistive Strain Sensing Behaviors of Carbon Nanotubes in One-Dimensional Polymer Fiber Structure

Senlong Yu,Xingping Wang,Hengxue Xiang,Liping Zhu,Mike Tebyetekerwa,Meifang Zhu

DOI: https://doi.org/10.1016/j.carbon.2018.08.028

IF: 10.9

2018-01-01

Carbon

Abstract:The fabrication of piezoresistive strain sensor with unified and balanced properties of high sensitivity, stretchability, and durability still remains a great challenge due to the oversimplified thin film structure of strain sensor. In this work, a high-performance strain sensor based on conductive poly(styrenebutadiene-styrene)/carbon nanotube fiber (SBS/CNT fiber, SCF) was prepared via wet-spinning. Then, the morphology, mechanical property, piezoresistive performance and sensing mechanism of the SCF-based sensors were systematically investigated. The resultant SCF-based sensors simultaneously demonstrated superior sensitivity (with a gauge factor of 175 under 50% deformation), wide workable range (>260%) and excellent durability due to the excellent flexibility of SBS polymer (the breaking elongation of pure SBS fiber > 1300%), high conductivity of CNT (10(5) S/cm) and the strong 17-17 interaction between CNT and SBS. These properties make the composite fiber a perfect fit to monitor various large deformation in a wide range of applications. Moreover, the associated sensing mechanism was also systematically explained by tunneling theory and the evolution of the conductive network during the stretching-releasing process. (C) 2018 Elsevier Ltd. All rights reserved.
A THEORETICAL FRAMEWORK FOR DETECTING AND MONITORING GROUND FISSURES USING DISTRIBUTED FIBER OPTIC SENSING

ZHANG Chengcheng,SHI Bin,ZHU Honghu,TANG Chaosheng

DOI: https://doi.org/10.13544/j.cnki.jeg.2018-319

2019-01-01

Journal of Engineering Geology

Abstract:The detection and monitoring of ground fissures is vital to understand their mechanism and the prevention and control of related hazards. Recently, high-and ultra-high-resolution distributed fiber optic sensing(DFOS) techniques have been developed and applied in the field of geoengineering. This provides a technological basis for improved detection and monitoring of ground fissures. This paper discusses a theoretical framework for ground fissure detection and sensing using the DFOS technique. Based on the tensile failure mode of soil during ground fissure formation and by considering that DFOS captures linear strains, a strain-based failure criterion is proposed as follows:Rs=e3/et, where et is the ultimate tensile strain of soil and e3 is the minimum principal strain. A value of Rs larger than 1 means that the absolute value of the minimum principal stress has exceeded the ultimate tensile strain of soil. Hence, tensile failure may occur. The ground fissure monitoring results are influenced by a combined effect of spatial resolution, fiber optic cable-soil interaction, strain localization, temperature variation, and strain transfer efficiency. These effects and their countermeasures are also analyzed and discussed. To improve the quality of DFOS-based monitoring, these effects should be carefully addressed according to different geologic conditions and monitoring schemes.
Temperature and Strain Sensor Based on a Few-Mode Photonic Crystal Fiber

Haihu Yu,Zhou Zheng,Jian Ma,Yu Zheng,Minghong Yang,X. Jiang

DOI: https://doi.org/10.1109/icsens.2017.8233965

2017-01-01

Abstract:A fiber optic sensor for simultaneous measurement of temperature and strain is demonstrated, based on a few-mode solid-core photonic crystal fiber. In the core of the few-mode fiber, the fundamental mode and the first higher order mode are co-excited, when coupling light from a collapsed end, through a single-mode fiber. Mach-Zehnder interferences between the two core modes and one possible cladding mode are observed. The interference characteristics vary accordingly, with the change of temperature and applied strain. This system gives a sensitivity of 9.85 pm/°C and 3.24 pm/με, respectively.
Characterizing the strain transfer on the sensing cable-soil interface based on triaxial testing

Guan-Zhong Wu,Dan Zhang,Tai-Song Shan,Bin Shi,Yuan-Jiang Fang,Kang Ren

DOI: https://doi.org/10.12989/sss.2022.30.1.063

IF: 4.581

2022-01-01

Smart Structures and Systems

Abstract:The deformation coordination between a rock/soil mass and an optical sensing cable is an important issue for accurate deformation monitoring. A stress-controlled triaxial apparatus was retrofitted by introducing an optical fiber into the soil specimen. High spatial resolution optical frequency domain reflectometry (OFDR) was used for monitoring the strain distribution along the axial direction of the specimen. The results were compared with those measured by a displacement meter. The strain measured by the optical sensing cable has a good linear relationship with the strain calculated by the displacement meter for different confining pressures, which indicates that distributed optical fiber sensing technology is feasible for soil deformation monitoring. The performance of deformation coordination between the sensing cable and the soil during unloading is higher than that during loading based on the strain transfer coefficients. Three hypothetical strain distributions of the triaxial specimen are proposed, based on which theoretical models of the strain transfer coefficients are established. It appears that the parabolic distribution of specimen strain should be more reasonable by comparison. Nevertheless, the strain transfer coefficients obtained by the theoretical models are higher than the measured coefficients. On this basis, a strain transfer model considering slippage at the interface of the sensing cable and the soil is discussed.

Sensing the Earth Crustal Deformation with Nano-strain Resolution Fiber-optic Sensors

Highly Sensitive and Fast Response Strain Sensor Based on Evanescently Coupled Micro/nanofibers

Vertically Distributed Sensing of Deformation Using Fiber Optic Sensing

Large detection range and high strain sensitivity fiber SPR sensor based on wave structure

Fiber-optic Wireless Sensor Network Using Ultra-Weak Fiber Bragg Gratings for Vertical Subsurface Deformation Monitoring

High-Sensitivity Microfiber Strain and Force Sensors

Distributed and multimodal strain sensing performance of flexible hydrogel functional optical fibers

Toward Distributed Fiber‐Optic Sensing of Subsurface Deformation: A Theoretical Quantification of Ground‐Borehole‐Cable Interaction

Monitoring Flexure Behavior of Compacted Clay Beam Using High-Resolution Distributed Fiber Optic Strain Sensors

Role of the interface between distributed fibre optic strain sensor and soil in ground deformation measurement

High Precision Temperature Insensitive Strain Sensor Based on Fiber-Optic Delay

Temperature Insensitive Distributed Wide-dynamic-range Strain Sensing based on Polarization-Maintaining Photonic Crystal Fiber

Microanchored borehole fiber optics allows strain profiling of the shallow subsurface

Hollow-porous fiber-shaped strain sensor with multiple wrinkle-crack microstructure for strain visualization and wind monitoring

Advanced Fiber Optic Sensing for Cryogenic Simultaneous Temperature and Strain Measurement

Quantitative Evaluation of Optical Fiber/Soil Interfacial Behavior and Its Implications for Sensing Fiber Selection

Strain integration-based soil shear displacement measurement using high-resolution strain sensing technology

Superior Piezoresistive Strain Sensing Behaviors of Carbon Nanotubes in One-Dimensional Polymer Fiber Structure

A THEORETICAL FRAMEWORK FOR DETECTING AND MONITORING GROUND FISSURES USING DISTRIBUTED FIBER OPTIC SENSING

Temperature and Strain Sensor Based on a Few-Mode Photonic Crystal Fiber

Characterizing the strain transfer on the sensing cable-soil interface based on triaxial testing