Abstract:Titanium matrix composites synthesized using powder metallurgy methods have attracted significant attention due to their extraordinary mechanical properties. In this study, cost-effective and high-performance TiC/Ti-6Al-4 V matrix composites were synthesized and characterized using a combined elemental powder mixing and spark plasma sintering method. Studies on the effect of graphene nanoplate (GNP) content on microstructures of Ti-6Al-4 V matrix composites showed typical Widmanstatten structures without apparent pores and microcracks. The grain size of composites was decreased significantly with the increase of GNP content, mainly due to the pinning effect of in-situ generated TiC particles at grain boundaries, which limited the rapid grain growth of the matrix. Mechanical test results showed that their yield strength and ultimate tensile strength were 889.0 MPa and 988.3 MPa, respectively, and their total fracture elongation was maintained at ∼14.2 %. GNPs/Ti-6Al-4 V exhibited superior strength (e.g., yield and ultimate tensile strength of 1028.4 and 1121.6 MPa, which are 14.4 % and 13.5 % higher than those of the matrix) and maintained a good ductility of ∼ 9.8 % with only 0.1 wt% GNP addition. Carbon nanomaterial (such as graphene nanoplates) induced the precipitation of needle-like nano-secondary phases in trigeminal grain boundary β phases, which strengthened the β-Ti soft phase. The reinforced strength of the composite is mainly attributed to the grain refinement, secondary α phases precipitation strength and dislocations strengthening. This work provides a new methodology for fabrication of high-performance titanium matrix composites (TMCs) combination blended elemental powder metallurgy (BEPM) and sintering technology.

Fabrication of Ti<sub>66</sub>V<sub>13</sub>Cu<sub>8</sub>Ni<sub>6.8</sub>Al<sub>6.2</sub> Bulk Composites with High Strength by Spark Plasma Sintering and Crystallization of Amorphous Phase

Equiaxed Ti-based Composites with High Strength and Large Plasticity Prepared by Sintering and Crystallizing Amorphous Powder

Microstructure and Mechanical Properties of Nanocrystalline Wc-Particle-Reinforced Ti-Based Composites with Nano/Ultrafine-Grained Intermetallic Matrix from Spark Plasma Sintering and Crystallization of Amorphous Phase

Mechanical Alloying and Spark Plasma Sintering of Ni-Al-Ti-B Powders for Fabricating Nanocrystailine (Tib+tib2)/ni-3(Al, Ti) Composite

Fabrication of Amorphous Ti63.7Nb21.3Zr4.5Ta1.5Fe9 Powder by Mechanical Alloying

Synthesis, characterization, and mechanical behavior of ultra-fine-grained Ti-6Al-5V alloy prepared by mechanical alloying and spark plasma sintering

Synthesis of Highly Amorphous Fe 70 Ti 2 Y 6 B 22 Bulk Alloy with Excellent Thermal Stability by Isothermal Compression under High Pressure

Fabrication of Ti2AlC/Ti-44Al-6Nb-0.3Y composite by spark plasma sintering

Microstructures Of Components Synthesized Via Electron Beam Selective Melting Using Blended Pre-Alloyed Powders Of Ti6al4v And Ti45al7nb

Mechanically Alloyed Amorphous Ti50(Cu0.45Ni0.55)44–xAlxSi4B2 Alloys with Supercooled Liquid Region

Fabrications and mechanical properties of bulk amorphous, nanocrystalline, nanoquasicrystalline alloys in aluminum-based system

Synthesis and Properties of an Ultrafine Grained Ti-45al-2cr-2nb-1b-0.5ta Alloy Prepared by Double Mechanical Milling and Spark Plasma Sintering

Fabrication of 10mm diameter fully dense Al86Ni6Y4.5Co2La1.5 bulk metallic glass with high fracture strength

Microstructure Evolution and Mechanical Properties of Ti46.5Al2Cr1.8Nb-(W, B) Alloys Fabricated by Spark Plasma Sintering and Pulse Current Assisted Isothermal Forging

Microstructure and Mechanical Properties of a High-Strength Ti-4Al-2Fe-3Cu Alloy Fabricated by Sintering and Hot Extrusion

Mechanical synthesized nanocrystalline Ti/Al composite powders as precursor for Ti/Al alloy via reactive sintering

In-situ synthesized TiC/Ti-6Al-4V composites by elemental powder mixing and spark plasma sintering: Microstructural evolution and mechanical properties

Microstructures and mechanical properties of high strength Ti-XAl-2Fe-3Cu alloys fabricated by powder compact extrusion

High Strength Aluminium Alloys Prepared by Nanocrystallisation of Amorphous Powders Using Spark Plasma Sintering

Synthesis of TiAl/Nb Composites with Concurrently Enhanced Strength and Plasticity by Powder Metallurgy

Fabrication of Ti&lt;sub&gt;66&lt;/sub&gt;V&lt;sub&gt;13&lt;/sub&gt;Cu&lt;sub&gt;8&lt;/sub&gt;Ni&lt;sub&gt;6.8&lt;/sub&gt;Al&lt;sub&gt;6.2&lt;/sub&gt; Bulk Composites with High Strength by Spark Plasma Sintering and Crystallization of Amorphous Phase