Abstract:Using hydroxypropyl terminated polydimethylsiloxane ( HP. PDMS ), isophorone diisocyanate and 2,2-bis( hydroxymethyl ) butyric acid as starting materials, silicone-polyurethane copolymer ( Si-PU ) latexes with particle diameter of about 50 nm were prepared via step-by-step feeding process followed by phase inversion technique in the absence of surfactant. Influences of the HP-PDMS content on the phase structure and the properties of the Si-PU latex films were investigated, and the difference between Si-PU and polyether polyurethane ( E-PU ) was emphasized. It was found that the content of PDMS in Si-PU could reach up to 65 wt%. Results of DSC analysis showed that, in comparison with the E-PU latex film, the Si-PU latex films exhibited well phase separation. Strong hydrogen bonding in Si-PU hard segments was confirmed by FTIR, which promoted the micro. phase separation in the latex films. On the contrary, strong hydrogen bonding existed in between the soft and hard segments in E-PU, which led to phase mixing and prevented the formation of phase separation structure. The Si-PU latex films were characterized by AFM tapping mode and the formation of sea. island phase separation was observed, and this kind of phase separation structure in the Si-PU latex films was rarely reported in the literature, in which the amorphous PDMS. enriched domains constituted the dispersed phases. With the increase in HP. PDMS content, the degree of phase separation in the Si-PU latex films increased as well, which led to the decrease of elastic modulus from 400.0 MPa to 32.2 MPa with an increase in elongation at break and in the flexibility. The initial decomposition temperature of the Si-PU latex films was at about 244 degrees C, which was 18 degrees C lower than that of the E-PU latex film due to the low degree of hydrogen bonding between the soft and the hard segments, whereas the thermal stability of Si-PU at high temperature zone was much better than E-PU. Compare to the E-PU latex film, a low water adsorption rate under 11% and a high contact angle above 94 degrees indicated excellent water resistance of the Si-PU latex films.

Preparation and characterization of polyurethan-<i>block</i>-poly(trifluoro- propylmethyl)siloxane elastomers

Preparation and characterization of polyurethan-block-poly(trifluoropropylmethyl)siloxane elastomers

Preparation and Film Properties of Cross-Linking Siliconated Polyurethane-Fluorinated Acrylate Hybrid Emulsion

Structure and Solvent-Resistant Property of Fluorinated Polyurethane Elastomer

Synthesis of Poly(methyl (trifluoropropyl) Siloxane) and Its Crosslinking Characteristics

Synthesis and characterization of polyurethane–polysiloxane block copolymers modified by α,ω-hydroxyalkyl polysiloxanes with methacrylate side chain

Synthesis and Characterization of Random Block Hydroxyl-Terminated Polyfluoroether-Based Polyurethane Elastomers with Fluorine-Containing Side Chains

Investigation on the Preparation of Silicone-polyurethane Latex, Phase Structure and Property of the Latex Films

Microstructure and performance of polytrifluoropropylmethylsiloxane prepared by reaction extrusion

Synthesis of Polyurethane-Acrylate Hybrid Emulsion Containing Siloxane and Fluorine

Synthesis And Surface Property Of Siloxane-Modified Aqueous Polyurethane

Microphase Separation and Properties of Polyurethane Elastomers Containing Sulfuryl Group Chain-Extender

Synthesis of Poly[methyl(3,3,3-Trifluoropropyl)siloxane]- B -Poly(ethylene Oxide) Block Copolymers

Synthesis of A Novel Core-Shell Type Acrylic-Polyurethane Hybrid Emulsion Containing Siloxane and Fluorine As Well As Water and the Oil Resistances of Cured Film

Synthesis, characterization and properties of a novel fluorinated polyurethane

Mechanical and surface properties of polysulfide-based polyurea modified with aminoethylaminopropyl poly(dimethylsiloxane)

Preparation and Performance of Polyurethane-Acrylate-Styrene Hybrid Emulsion

Synthesis and Characterization of Polyurethane Urea Based on Fluorine‐containing Bisphenoxydiamine

Development of UV-curing organosilicon urethane acrylate prepolymer

Synthesis and Characterization of XDI-based Thermoplastic Polyether Polyurehtane Elastomers

Synthesis and Characterization of Hydroxy‐terminated Polyether‐polydimethylsiloxane‐polyether (PE‐PDMS‐PE) Triblock Oligomers and Their Use in the Preparation of Thermoplastic Polyurethanes