Abstract:A simplified predictive torque control (PTC) method is proposed to eliminate the flux weighting factor where torque cost function is evaluated for 19 voltage vectors (VVs), but flux cost function is evaluated for only five VVs with sector identification. This method also reduces computational burden on the processor. Permanent magnet synchronous motor (PMSM) drives are effectively used in the application of electric vehicles (EVs) due to their ease of construction and simpler in operation. Model predictive control (MPC) is an efficient control strategy used in motion control applications. Predictive torque control (PTC) is a type of MPC that selects a suitable voltage vector (VV) from a set of 19 VVs in order to minimize the cost function. However, as the control variables in the cost function in PTC are distinct, a weighting factor is essential. The tuning of the weighting factor is a burdensome control process. To address the limitations, the proposed PTC (P‐PTC) removes the weighting factor by using two cost functions, thus reducing flux ripples and torque ripples. Firstly, the P‐PTC evaluates the torque cost function for 19 VVs, and the VV that gives less value of torque error is used to find the sector number. The sector number is used to choose the five VVs from that sector and evaluate flux cost function to get an optimal VV. Therefore, the P‐PTC give less ripples in torque and flux by enhancing steady‐state response. The effectiveness of the P‐PTC is validated through both simulation and experimentation for a 3.7 kW OEW‐IPMSM drive using d‐SPACE RTI1104 controller. The P‐PTC is also tested with a typical urban dynamometer drive cycle (UDDC) with rapid accelerations and decelerations to ensure its application in EVs using the OPAL RT 1250 controller.

Weightless Model Predictive Torque Control of Induction Motor with Simplified Candidate Voltage Vectors Set

Two-Vector-Based Model Predictive Torque Control Without Weighting Factors for Induction Motor Drives

A Sequential Direct Torque Control Scheme for Seven-Phase Induction Machines Based on Virtual Voltage Vectors

Deadbeat Model-Predictive Torque Control With Discrete Space-Vector Modulation for PMSM Drives

Model predictive flux control for permanent magnet synchronous motor

Model Predictive Torque Control for Dual Three-Phase PMSM based on Novel Virtual Voltage Vector

A Modified Deadbeat Predictive Flux Control for Reducing Torque Ripple at Low Modulation Ratio

An Improved Model Predictive Torque Control for Switched Reluctance Motors with Candidate Voltage Vectors Optimization

An Error Tracking Dead-beat Model Predictive Torque Control for Open-Winding Permanent Magnet Synchronous Motor with Common DC Bus

An Improved Model Predictive Torque Control for PMSM Drives Based on Discrete Space Vector Modulation

Predictive Torque Control for PMSM Based on Weighting Factor Elimination and Fast Voltage Vector Selection

A Modified Deadbeat Predictive Current Control for Improving Dynamic Performance of PMSM

A Novel Torque Ripple Reduction Strategy for Predictive Direct Torque Controlled Pmsg

Model Predictive Torque Control of Surface Mounted Permanent Magnet Synchronous Motor Drives with Voltage Cost Functions

An Improved Model Predictive Direct Torque Control Strategy for Reducing Harmonic Currents and Torque Ripples of Five-Phase Permanent Magnet Synchronous Motors.

A Modified Deadbeat Predictive Current Control with Improved Dynamic Performance under Insufficient Voltage Margin for IPMSM

A novel weighting factor determined method of model predictive torque control for permanent magnet synchronous motor

A Robust Deadbeat Predictive Current Control Method for IPMSM

Simple predictive torque control of an open‐end winding interior permanent magnet synchronous motor drive without weighting factor for electric vehicle applications

Direct Torque Control for Induction Motors Based on Minimum Voltage Vector Error

Three-Vector-Based Model Predictive Torque Control for a Permanent Magnet Synchronous Motor of EVs