Abstract:In this work, the structural and mechanical properties of ternary Mo-Al-N alloys are investigated by combining thin film growth experiments and density functional theory (DFT) calculations. Mo1−xAlxNy thin films (∼300 nm thick), with various Al fractions ranging from x = 0 to 0.5 and nitrogen-to-metal (Al + Mo) ratio ranging from y = 0.78 to 1.38, were deposited by direct-current reactive magnetron cosputtering technique from elemental Mo and Al targets under Ar + N2 plasma discharges. The Al content was varied by changing the respective Mo and Al target powers, at a fixed N2 (20 SCCM) and Ar (25 SCCM) flow rate, and using two different substrate temperatures Ts = 350 and 500 °C. The elemental composition, mass density, crystal structure, residual stress state, and intrinsic (growth) stress were examined by wavelength dispersive x-ray spectroscopy, x-ray reflectivity, x-ray diffraction, including pole figure and <math> si n 2 ψ</math> measurements, and real-time in situ wafer curvature. Nanoindentation tests were carried out to determine film hardness H and elastic modulus EIT, while the shear elastic constant C44 was measured selectively by surface Brillouin light spectroscopy. All deposited Mo1−xAlxNy films have a cubic rock-salt crystal structure and exhibit a fiber-texture with a [001] preferred orientation. The incorporation of Al is accompanied by a rise in nitrogen content from 44 to 58 at. %, resulting in a significant increase (2%) in the lattice parameter when x increases from 0 to 0.27. This trend is opposite to what DFT calculations predict for cubic defect-free stoichiometric Mo1−xAlxN compounds and is attributed to variation in point defect concentration (nitrogen and metal vacancies) when Al substitutes for Mo. Increasing Ts from 350 to 500 °C has a minimal effect on the structural properties and phase composition of the ternary alloys but concurs to an appreciable reduction of the compressive stress from −5 to −4 GPa. A continuous increase and decrease in transverse sound velocity and mass density, respectively, lead to a moderate stiffening of the shear elastic constant from 130 to 144 GPa with increasing Al fraction up to x = 0.50, and a complex and nonmonotonous variation of H and EIT is observed. The maximum hardness of ∼33 GPa is found for the Mo0.81Al0.19N1.13 film, with nitrogen content close to the stoichiometric composition. The experimental findings are explained based on structural and elastic constant values computed from DFT for defect-free and metal- or nitrogen-deficient rock-salt MoAlN compounds.

Control of Roughness in Mo/Al Multilayer Film Fabricated by DC Magnetron Sputtering

Magnetic Anisotropy and High Frequency Permeability of Multilayered Nanocomposite FeAlO Thin Films

Soft Magnetic Properties and High Frequency Permeability in [coalo/oxide] Multilayer Films

Optical and Wetting Properties of CuAlO2 Films Prepared by Radio Frequency Magnetron Sputtering

Ion-assisted sputter deposition of molybdenum-silicon multilayers

Structure and Magnetic Properties of Fe/Al Multilayers Synthesized by Planar Magnetron Sputtering

Microstructural and electrical behavior of NiCr/Al nanomultilayered films prepared by magnetron sputtering

Optimizing hardness of CN x thin films by dc magnetron sputtering and a statistical approach

Synthesis of Al Thin Films with High Optical Transmittance by DC Magnetron Sputtering Process Parameter Optimization

Residual strain and electrical resistivity dependence of molybdenum films on DC plasma magnetron sputtering conditions

Magnetic Co/Al Multilayers Prepared by Planar Magnetron Sputtering

Synthesis, microstructure and properties of MoAlB MAB phase films

Performance, structure, and stability of SiC/Al multilayer films for extreme ultraviolet applications

Individual Layer Thickness Dependence of Microstructure and Mechanical Properties of Magnetron Sputtering Mo-W-Doped Ni/Ni3Al Multilayers

Influence of underlayer roughness on the properties of Sc0.4Al0.6N thin films prepared via sputter deposition

Structure, stress, and mechanical properties of Mo-Al-N thin films deposited by dc reactive magnetron cosputtering: Role of point defects

The growth mode of α-Fe2O3 thin films by DC magnetron sputtering

Structural Characterization Of Ta/Al Multilayer Films

Growth of hard metal films by deep oscillation magnetron sputtering

A study into enhanced oxidation resistance and its mechanism in Cr1-xAlxN/CrN/Cr multilayer films deposited on 9–12 % Cr heat-resistant steel

Investigation on Solar Absorption and Thermal Emittance of Al Films Deposited by Magnetron Sputtering