Abstract:High strength and ductile nickel aluminum bronze (NAB) alloys were produced by heavy warm rolling (HWR) and subsequent annealing at various temperatures. The effect of annealing temperatures ranging from 473 K to 1173 K (200 °C to 900 °C) on the microstructure, mechanical, and electrochemical properties of these HWRed NAB alloys was studied. The results show that the evolution of microstructure and mechanical behavior can be divided into three distinct stages with the increasing annealing temperature. When annealed below 500 °C (Stage A), the HWRed samples exhibit ultrahigh strength and good ductility. Such remarkable tensile properties are mainly attributed to the ultrafine α grains and nano k precipitates. Part of the α phase recrystallized, contributing to a further decrease in the average grain size. An ultrahigh ultimate strength of 1363 MPa and uniform elongation of 6.0 pct can be obtained when the alloy is annealed at 400 °C for 1 hour. When annealed at 600 °C and 700 °C (Stage B), a prominent strength–ductility combination with a yield strength of about 1000 MPa and an elongation of about 15 pct can be achieved, mainly due to the uniform ultrafine microstructures and the high-density annealing twins. Some nano k phases with grain size less than 20 nm precipitate dispersedly in α grains, which may also be a significant strengthening factor. When the temperature reaches above 800 °C (Stage C), the yield strength reduces dramatically, while the elongation and ultimate strength further increase. At this stage, the matrix transforms from single ultrafine α grains into a fine-grained ( α + β ′) duplex structure with high-density ultrafine annealing twins inside α grains. It is found that the mechanical properties of the HWRed and annealed alloys are greatly enhanced, while the electrochemical stability almost shows no deterioration compared with the undeformed coarse-grained alloys. This indicates that HWR and subsequent annealing is an effective strategy for preparing bulk NAB alloys with high performance.

Effects of Annealing on Mechanical Properties and Degradation Behavior of Biodegradable JDBM Magnesium Alloy Wires

Microstructure, mechanical and corrosion properties of Mg–Zn–Nd alloy with different accumulative area reduction after room-temperature drawing

Microstructure Evolution, Mechanical Properties and Corrosion Behavior of Biodegradable Zn-2Cu-0.8Li Alloy During Room Temperature Drawing

Effects of Extrusion and Heat Treatment on the Mechanical Properties and Biocorrosion Behaviors of A Mg-Nd-Zn-Zr Alloy

Mechanical and Corrosion Properties of Biodegradable Magnesium Mini-Tubes with Different Grain Morphologies: Size and Distribution

Improving Mechanical and Magnetocaloric Responses of Amorphous Melt-Extracted Gd-based Microwires Via Nanocrystallization

Microstructure evolution and ductility improvement of additively manufactured biodegradable zinc–magnesium alloys via annealing

Effect of Annealing on Microstructure Evolution and Age-Hardening Behavior of Dilute Mg–Al–Ca–Mn Alloy

The processing of Mg alloy micro-tubes for biodegradable vascular stents

Effect of annealing treatment on texture evolution, microstructure and mechanical properties of an extruded Mg-Gd-Zn-Zr alloy

Microstructure, Mechanical Properties, Biocorrosion Behavior, and Cytotoxicity of As-Extruded Mg–Nd–Zn–Zr Alloy with Different Extrusion Ratios

Effect of annealing treatment on the microstructure and mechanical properties of warm-rolled Mg–Zn–Gd–Ca–Mn alloys

Biocorrosion properties of as-extruded Mg-Nd-Zn-Zr alloy compared with commercial AZ31 and WE43 alloys

Research Progress of Microstructure Characteristics and Mechanical Properties of Hot-Deformed Biodegradable Mg-based Alloys

Fabrication of Ultra-High Strength Magnesium Alloys over 540 MPa with Low Alloying Concentration by Double Continuously Extrusion

Microstructure and In Vitro Evaluation of Extruded and Hot Drawn Alloy MgCa0.7 for Biodegradable Surgical Wires

Effect of original grain size on microstructure and properties of extruded Mg-2Zn-0.2Mn biomedical alloy

Optimizing Mechanical Property and Cytocompatibility of the Biodegradable Mg-Zn-Y-Nd Alloy by Hot Extrusion and Heat Treatment

Effect of Annealing Temperature on Microstructure and Properties of a Heavy Warm Rolled Nickel Aluminum Bronze Alloy

Fine-grained Structure and Recrystallization at Ambient Temperature for Pure Magnesium Subjected to Large Cold Plastic Deformation

Superior Strength-Ductility Synergy of Mg-Nd-Zn-Zr Alloy Rod Achieved by Drawing at Elevated Temperatures