Abstract:Cold crucible induction melter (CCIM) technology has been widely used in melting of non-metallic refractory materials with a high melting point and a requirement of high purity. This paper discusses the application of the CCIM technology in melting of reactor corium (simulated as zirconium oxide in this experiment).In this experiment, the power supply is set at constant power control mode, with a design frequency of similar to 100 kHz and a total output power of similar to 400 kW. The cold crucible consists of copper tubes and a stainless bottom plate which has a dimension of 220 mm in diameter and 420 mm in height. The crucible is charged with zirconium oxide (ZrO2) powder and surrounded by a set of water-cooling induction coils which is designed shorter than the crucible in order to reduce energy loss in the water-cooling bottom plate. The top of the crucible and the coils are at the same height. A Zirconium ring is used to initiate heating process. similar to 50 kg ZrO2 powder is used for each experiment. Electrical variables of the induction melter and temperature of the melt are detected and recorded in the entire heating process.For the result, almost 3/4 of the ZrO2 powder is melt and a thin crust (2-3 mm) is generated between the melt and the crucible. To be specific, the ZrO2 powder above the bottom of the induction coils is melt, but others are not. In the melting process, the maximum surface temperature of the melt has reached 2230 t. Furthermore, for better understanding of the relationship between the melting process and the changing process of the electrical variables, an equivalent circuit of the heating system is established and analyzed. It can be concluded that some electrical variables such as the quality factor (Q) of the induction coils and the practical frequency can reflect melting status. The conclusion is confirmed by the records transmitted by sensors in the melting process. By comparison between the recorded data and the melting status, it is clear that the Q value can be accurately used in indicating the melting status due to its obvious change in the entire melting process. As the melting pool becoming larger, the Q value tends to be smaller. In contrast, the practical frequency becomes higher as the melt becoming larger. Furthermore, both of them are not influenced by the output power. In addition, the output current and the output voltage also can be used to describe the melting status. In specific, a larger melting pool corresponds to a lower output current and a higher output voltage.

Experimental Study on Molten Corium-Concrete Interaction with Simulant Metal and Oxide

Corrosion behavior and failure mechanism of amorphous Al2O3 coating at high-temperature LBE

Study on corium-concrete interaction, heat transfer, and concrete ablation: Impact of replacing Zircaloy cladding with accident tolerant silicon carbide cladding on corium characteristics

A Thermal Approach for Modeling Concrete Ablation During Molten Corium–Concrete Interaction

Experimental Study Of Performance Of Cold Crucible Induction Melter In Melting Corium Simulant

Analysis of the Long-Term Interaction Between Molten Core and Dry Concrete at Fukushima Daiichi Unit 1

Experimental Investigation on Contact Angles of Molten Lead–Lithium on Silicon Carbide Surface

Investigation of the interaction between corium and metal-coolers at the VCG-135 test bench in the conditions of a severe accident

Three-dimensional Experiment of Heat Transfer for Molten Oxidic Pool

Simulant molten core–concrete interaction experiments in view of understanding Fukushima Daiichi Nuclear Power Station Cs-bearing particles generation mechanism

Modeling of an ACE-L4 experiment on the interaction of the melt with concrete used in the construction of VVER-1000 NPPs

Experimental Study of Thermal-Hydraulic-Mechanical Coupling Behavior of High-Performance Concrete

The normative need for tooth extractions in older adults in Ontario, Canada.

Investigation of prototypical corium interaction with samples of VVER-1000 in-vessel and ex-vessel structures

Corrosion mechanism of cement-bonded Al2O3–MgAl2O4 pre-cast castables in contact with molten steel and slag

CFD Simulation of Melt Pool Coolability in a Simulated Core Catcher Model

Eutectic melting and relocation behavior of B4C pellet-stainless steel under radiative heating

Hermeticity of SiC/SiC composite and monolithic SiC tubes irradiated under radial high-heat flux

In situ high-temperature 3D imaging of the damage evolution in a SiC nuclear-fuel cladding material

Microstructure and ablation behaviour of C/C-SiC-ZrC-Cu composites prepared by reactive melt infiltration

Characterization and mechanism analysis of interaction between Inconel 713C superalloy and a novel crucible-shell "integrated" mold