Abstract:The ultra-long gravity heat pipe has a long heat transfer distance and narrow working fluid flow channel within its tube. Due to these unique design features, the vapor–liquid counter-flow and heat transfer characteristics of these heat pipes are more complex than those found in conventional-size heat pipes. This paper innovatively proposes the design of a segmented visualization window structure of an ultra-long gravity heat pipe, which successfully overcomes the challenge of visualizing the internal flow during operations. A visualization experimental platform, measuring 40 m in height with an inner diameter of 7 mm and the aspect ratio up to 5714, was built to investigate the evolving characteristics of two-phase flows with an increasing heat input and the impact of the phase change flow characteristics on the thermal performance of ultra-long gravity heat pipes. The results obtained can provide guidance for the development of the internal structure of ultra-long gravity heat pipes that are being applied in exploiting geothermal energy. The results show that, at low heat input (200 W, 250 W), there are separate flow paths between the condensate return and the steam, but the high hydrostatic pressure due to the height of the liquid injection results in the presence of an unsaturated working fluid with a higher temperature in the liquid pool area, which has a lower evaporation rate, limiting the heat transfer through the heat pipe. It is found that if increasing the heat input up to 300 W, the evaporative phase change in the heating section becomes intense and stable. At the same time, despite the intermittent formation of liquid columns in the adiabatic section due to the vapor–liquid rolls, which increases the resistance to the vapor–liquid counter-flow, the liquid columns are blocked for a short period of time, and the path of steam rises and the condensate return is smooth, which does not seriously affect the steam condensation and liquid return evaporation. At this point, the overall temperature of the heat pipe is evenly distributed along the tube and the heat transfer performance is optimal. When the heat input further increases (350 W, 400 W), a large amount of condensate is trapped in the upper part of the adiabatic section and the condensing section by long liquid plugs for a long time. At this point, the condensate flow back to the heating section is significantly reduced, and the steam is seriously prevented from entering the condensation section, resulting in a significant increase in the temperature gradient between the lower part of the evaporating section and the upper part of the adiabatic section and deterioration of the heat transfer performance.

The Heat Transfer Capacity of Multi-Layer Wick Heat Pipe Tested in Anti-Gravity Orientations

Structural effect of internal composite wick on the anti-gravity heat transfer performance of a concentric annular high-temperature heat pipe

Experimental Investigation on the Temperature Distribution Characteristics of the Evaporation Section in a Pulsating Heat Pipe

Pore size optimization and fluid channel analysis of composite wick and anti-gravity study

Experimental study on thermal performance of ultra-thin heat pipe with a novel composite wick structure

Heat Transfer Capacity Optimization Design of Microgroove and Microcolumn in an Ultra-Thin Flat Heat Pipe

Enhanced capillary pumping performance of flexible heat pipe device with multi cross-section ultra-thin wick

Thermal Performances Investigation of Anti-Gravity Heat Pipe with Tapering Phase-Change Chamber

Fabrication and capillary characterization of multi-scale micro-grooved wicks with sintered copper powder

Fabrication and capillary performance of a novel composite wick for ultra-thin heat pipes

Characterization of high-performance nanostructured wick for heat pipes

Thermal performance enhancement of an ultra-thin flattened heat pipe with multiple wick structure

Sintered Wick Heat Pipes with Excellent Heat Transfer Capabilities—Case Study

Performance tests on triple composite mesh-groove-powder wicks in a visualizable flat-plate heat pipe

Analysis of thermal characteristics of the heat pipes with segmented composite wicks

Application of biporous wick in flat-plate loop heat pipe with long heat transfer distance

Two-Phase Flow Visualization and Heat Transfer Characteristics Analysis in Ultra-Long Gravity Heat Pipe

An Experimental Study of a Composite Wick Structure for Ultra-Thin Flattened Heat Pipes

Influence of packing density on performance of porous wick for LHP

Ultra-efficient Heat Pipes Enabled by Nickel-Graphene Nanocomposite Coatings: Concept and Fundamentals

Enhanced capillary performance of nanostructures copper woven mesh wick for ultrathin heat pipes