Abstract:The flow condensation heat transfer coefficient of R134a inside two helical micro-fin tubes with outer diameter of 6.35 mm and helical angles of 18o and 28o respectively were experimentally studied at a high mass flux ranging from 500 to 1100 kg m−2 s−1. The condensation temperatures are 35°C, 40°C and 45°C, and the vapor qualities ranges from 0.95 to 1.00 at the inlet section and from 0.00 to 0.05 at the outlet section. Experimental results show that there are annular and intermittent flow regimes inside the tube under experimental conditions, the ratio of annular flow region to the total heat transfer region is about 70%. The liquid film flow changes from rotational flow to coexistence of rotational and horizontal flows when the vapor quality is 0.475±0.08, 0.486±0.06 and 0.521±0.05, respectively and the corresponding saturation temperature is 35°C, 40°C and 45°C. Based on the experimental data, the heat transfer coefficient increases with increasing mass flux and fin helical angle, and with decreasing saturation temperature and Reynolds number of cooling water. In addition, the heat transfer coefficient of annular flow is greater than that of intermittent flow, in other words, the heat transfer coefficient increases with increasing vapor quality. The heat transfer coefficient obtained at high mass flux was compared with the calculated data of some published correlations used at low mass flux. It was found that most correlations underestimate the experimental heat transfer coefficient inside the micro-fin tube, and these prediction deviation increases with increasing mass flux and fin helical angle. By introducing some dimensionless numbers as well as considering the flow mechanism of liquid film inside the tube, two heat transfer coefficient correlations were proposed based on the experimental data. The ratio of liquid film thickness to fin height was used to characterize whether the liquid film flow is rotational flow or coexistence of rotational and horizontal flows in the proposed correlation, which shows a better prediction accuracy with a mean deviation of less than 7.3%.

Experimental Investigation on Flow Boiling Heat Transfer of R134a in a Minichannel Heatsink with Copper Foam Fins

Flow Boiling Heat Transfer in Copper Foam Fin Microchannels with Different Fin Widths Using R134a

Flow Boiling Heat Transfer and Pressure Drop Characteristics of Water in a Copper Foam Fin Microchannel Heat Sink

Experimental Investigation on the Heat Transfer Performance and Evaporation Temperature Fluctuation of a New-Type Metal Foam Multichannel Heat Pipe

Theoretical and Experimental Research on Flow Boiling Heat Transfer in Microchannels for IGBT Modules

Two-phase Flow Oscillation and Distribution in Parallel Channels During R1233zd(E) Subcooled Flow Boiling: A Numerical Study

Experimental Investigation on Flow Boiling Instability of R1233zd(E) in a Parallel Mini-Channel Heat Sink for the Application of Battery Thermal Management

Visualization of R1233zd(E) Flow Boiling in Parallel Mini-channels

An experimental study on two-phase flow patterns and heat transfer characteristics during boiling of R134a flowing through a multi-microchannel heat sink

Experimental study of flow boiling in microchannel heat sink enhanced with partially in-line pin fins fence arrangement

Pool Boiling Heat Transfer of R141b on Surfaces Covered Copper Foam with Circular-Shaped Channels

An Experimental Study of the Effects of Porosity and Ratio of Fin to Channel Width on Water Flow Boiling in Copper Foam Fin Microchannels

Experimental Study of Condensation Heat Transfer of R134a Inside the Micro-Fin Tubes at High Mass Flux

Experimental study on flow boiling characteristics of R134a inside high-heat-flux microchannels

Experimental investigation of heat transfer and flow characteristics in finned copper foam heat sinks subjected to jet impingement cooling

Experimental study on flow boiling in ultrahigh-aspect-ratio copper microchannel heat sink

Experimental study on thermal and flow characteristics of metal foam heat pipe radiator

Experiment on Boiling Heat Transfer of Refrigerant R134a in Mini-channels

Experimental investigation of flow boiling characteristics in microchannel with triangular cavities and rectangular fins

Flow Boiling of R134a in an Open-Cell Metal Foam Mini-Channel Evaporator

Numerical Investigation of Fluid Flow and Heat Transfer in High-Temperature Wavy Microchannels with Different Shaped Fins Cooled by Liquid Metal