Abstract:In this study, microstructures and mechanical properties of (TiBw+Ti 5 Si 3 )/TC11 composites fabricated by hot isostatic pressing and 2D forging were investigated. A α + β titanium alloy TC11 (Ti-6.4Al-3.5Mo-1.4Zr-0.25Si) was used as a matrix material. The TiB 2 addition corresponding to 5.0 and 3.5 vol% of TiB w and the Si addition corresponding to 2.0, 4.0 and 6.0 vol% of Ti 5 Si 3 were used as additives to the TC11 titanium alloy. TiB w and Ti 5 Si 3 reinforced TC11 titanium matrix composites were fabricated by hot isostatic pressing and 2D forging in the α + β temperature field at T = 980 °C. The microstructure of the as-forged composites was composed of nanoscale Ti 5 Si 3 particle within the β-phase and TiB w around TC11 matrix particle. The TiB w reinforcer tend to be distributed along the stretching deformation direction. Compared with the TC11 matrix alloy, the strength of the (2Ti 5 Si 3 +5TiB w )/TC11 composite after 2D forging at room temperature increased by about 90 MPa due to the fine-grain strengthening of the α-phase, the precipitation strengthening of the nanoscale Ti 5 Si 3 silicide, and the load transfer efficiency of TiB w . The main failure mechanism of the composites at room temperature is fracture of TiB w followed by ductile failure of the matrix. (2Ti 5 Si 3 +5TiB w )/TC11 is thought as the optimal choice for engineering application, which UTS and El. at 600 °C are 851 MPa and 11%, respectively, and corresponding values of parameters at 750 °C are 385 MPa and 21%, respectively. Compared to the maximum service temperature 500 °C of TC11 alloy, the service temperature of (2Ti 5 Si 3 +5TiB w )/TC11 composite can be improved by over 100 °C while retaining the similar tensile strength and elongation.

Optimizing the Local Microstructure and Mechanical Properties of Variable Section Particulate Reinforced Titanium Matrix Composites Component Based on Numerical Simulation and Isothermal Forming

Tailoring A Novel Network Reinforcement Architecture Exploiting Superior Tensile Properties of in Situ Tibw/Ti Composites

Enhancing Ductility of Titanium Matrix Composites by Multimodal Α-Grains

IN SITU TiBW/Ti COMPOSITES WITH A NOVEL QUASI- CONTINUOUS NETWORK REINFORCEMENT ARCHITECTURE

Synergistic strengthening behavior and microstructural optimization of hybrid reinforced titanium matrix composites during thermomechanical processing

Advances in Microstructure Control during Isothermal Forming of Ti-Alloy Large Complex Components by Near-β Local Forging

Numerical Modeling and Experimental Study of Microstamping Process for Fabricating Microchannels Using Thin Sheets of Titanium

Thermomechanical Processing of a Near-α Ti Matrix Composite Reinforced by TiBw

Optimization of hot gas pressure forming process for titanium alloy component

Enhancing strength-ductility synergy in nano-sized TiB 2 /Al composite via rapid solidification and thermo-mechanical processing

Evading the strength and ductility trade-off dilemma in titanium matrix composites through designing bimodal grains and micro-nano reinforcements

Achieving near equiaxed α-Ti grains and significantly improved plasticity via heat treatment of TiB reinforced titanium matrix composite manufactured by selective laser melting

Enhancing microstructure refinement and strengthening efficiency of TiBw/near α-Ti composites by combining solid-solution treatment with hot processing

Forming Analysis and Heat Treatment of TC31 Titanium Alloy Component with High Ribs and Thin Webs

Enhancing the Robustness of Rib-Groove Filling and Strain Homogeneity in the Isothermal Forging of Titanium Alloy Multi-Rib Components

Formability, densification behavior and hierarchical grain structure of laser-directed energy deposition of TiB reinforced titanium matrix composites

The Effect of Severe Plastic Deformation on the Microstructure and Mechanical Properties of (tib+tic) Reinforced Titanium Matrix Composites

Integrating Experimental and Computational Analyses for Mechanical Characterization of Titanium Carbide/Aluminum Metal Matrix Composites

Multiscale crystal plasticity finite element simulations of the deformation inhomogeneity of TiBw/TA15 composites with network-structured during hot rolling

Microstructures and mechanical properties of (TiBw+Ti 5 Si 3 )/TC11 composites fabricated by hot isostatic pressing and subjected to 2D forging

Simultaneous Improvement in Strength and Ductility of TC4 Matrix Composites Reinforced with Ti1400 Alloy and In Situ-Synthesized TiC