Abstract:The present study investigated influences of the Al3Sc particle content on the evolution of bimodal grain structure and mechanical properties at both room and elevated temperatures of Al–7Mg–Sc alloys processed by hard-plate rolling (HPR). Bimodal grain structures were obtained in HPRed Al–7Mg–Sc alloys where ultrafine/fine grains decreased in size and increased in amount with increasing volume fraction of Al3Sc precipitates. The formation and evolution of bimodal grain structure are associated with (i) the different stability of various-orientated grains, and (ii) the volume fraction of Al3Sc precipitates. Ultrafine/fine (sub) grains form preferentially along grain boundaries (GBs) of <001>//normal direction (ND)- and <111>//ND-oriented coarse grains during HPR. In contrast, the <101>//ND-oriented coarse grains show relatively high stability nearly without subdivision. Furthermore, increased volume fraction of Al3Sc precipitates in Al–7Mg–0.4Sc promotes dislocation accumulation, favoring recrystallization nucleation, and meanwhile restricts grain growth, which results in more and refined ultrafine/fine grains. Thereby, the refined grain structure and increased volume fraction of Al3Sc precipitates in the Al–7Mg–0.4Sc alloy contribute to improved room-temperature yield strength (YS) and elongation, i.e. ~482 MPa and ~8%, which is much higher than that of ~420 MPa and ~4% in the binary Al–7Mg alloy. Meanwhile, Al–7Mg–0.4Sc exhibited higher hardness when annealed at 150–300 °C and also higher YS when subjected to a tensile test at ≤ 200 °C due to the more stabilized grain structure pinned by dispersed Al3Sc and additional strengthening effect from Al3Sc precipitates. Nevertheless, when subjected to a tensile test at ≥ 250 °C, the Al–7Mg–0.4Sc alloy exhibited much lower YS than binary Al–7Mg. The transition could be explained by more favored grain boundary sliding (GBS) and great dislocation loss, due to the easier occurrence of dynamic recrystallization (DRX) in Al–7Mg–0.4Sc during tensile test at elevated temperatures.

Microstructure Evolution, Thermal Conductivity and Mechanical Properties of Hot-Rolling Al–Si–Fe–Mg Alloy under Different Reductions

The Influence of Warm Rolling Reduction on Microstructure Evolution, Tensile Deformation Mechanism and Mechanical Properties of an Fe-30Mn-4Si-2Al TRIP/TWIP Steel

Recrystallization Behavior and Mechanical Properties of Az31b Alloy During the Hot-Rolling Process

The Effect of Heat Treatments on the Microstructural Evolution of Twin-Roll-Cast Al-Fe-Si Alloys

Effect of rolling temperature on microstructure and mechanical properties of hot-rolled Mg-Al-Ca-Zn-Mn alloys

Influence of Asymmetric Rolling Process and Thickness Reduction on the Microstructure and Mechanical Properties of the Al–Mg-Si Alloy

Influence Mechanisms of Cold Rolling Reduction Rate on Microstructure, Texture and Magnetic Properties of Non-Oriented Silicon Steel

Dynamic recrystallization, texture and mechanical properties of high Mg content Al–Mg alloy deformed by high strain rate rolling

Effect of Rolling Reduction on Microstructures and Mechanical Properties of Sc-Containing Al-3.2Cu-1.5Li Alloy

Effect of Rolling Temperature on Microstructure and Properties of Al-Mg-Li Alloy

Fe-bearing phase formation, microstructure evolution, and mechanical properties of Al-Mg-Si-Fe alloy fabricated by the twin-roll casting process

Microstructure evolution, mechanical response, and corrosion resistance for a 2195 Al-Li alloy under different rolling reductions during cryorolling

Microstructure and mechanical property of multi-pass low-strain rolled Mg-Al-Zn-Mn alloy sheet

Influences of the Al3Sc particle content on the evolution of bimodal grain structure and mechanical properties of Al–Mg–Sc alloys processed by hard-plate rolling

Effects of Hot-Rolling Reduction on Microstructure, Texture and Magnetic Properties of High Silicon Steel Produced by Strip Casting

Microstructure, texture and mechanical properties of the rolled high modulus Mg-Y-Zn-Al-Li alloy

Effects Of Rolling Process On Microstructure And Mechanical Property Of 7050 Aluminum Alloy

Microstructure evolution and mechanical properties of Al-Cu-Li alloys with different rolling schedules and subsequent artificial ageing heat treatment

Effect of 1wt.%Bi addition on microstructure and mechanical property of Mg–3Al alloy by twin roll casting and hot rolling

Microstructure evolution behavior and mechanical mechanisms in a near α-Zr alloy by cold rolling

Enhancing mechanical properties of twin-roll cast Al–Mg–Si–Fe alloys by regulating Fe-bearing phases and macro-segregation