Abstract:The HfOx-based resistive random access memory (RRAM) has been extensively investigated as one of the emerging nonvolatile memory (NVM) candidates due to its excellent memory performance and compatibility with CMOS process. In this study, the influences of deposition ambient, especially the oxygen partial pressure during thin film sputtering, on the resistive switching characteristics are discussed in detail for possible nonvolatile memory applications. The Ni/HfOx/TiN RRAMs are fabricated, and the HfOx films with different oxygen content are deposited by a radio frequency magnetron sputtering at room temperature under different oxygen partial pressures. The oxygen partial pressures in the sputter deposition process are 2%, 4% and 6% relative to engineer oxygen content in the HfOx film. Current-voltage (I-V) measurements, X-ray photoelectron spectroscopy, and atomic force microscopy are performed to explain the possible nature of the stable resistive switching phenomenon. Through the current-voltage measurement, typical resistive switching behavior is observed in Ni/HfOx/TiN device cells. It is found that with the increase of the oxygen partial pressure during the preparation of HfOx films, the stoichiometric ratio of O in the film is improved, the root mean square (RMS) of the surface roughness of the film slightly decreases due to the slower deposition rate under a higher oxygen partial pressure, and the high resistance state (HRS) current decreases. In addition, by controlling the oxygen content of the device, the endurance performance of the device is improved, which reaches up to 10 3 under a 6% oxygen partial pressure. The HfOx films prepared at a higher oxygen partial pressure supply enough oxygen ions to preserve the switching effect. As the oxygen partial pressure increases, the uniformity of the switching voltage is improved, which can be attributed to the fact that better oxidation prevents the point defects (oxygen vacancies) from aggregating into extended defects. Through the linear fitting and temperature test, it is found that the conduction mechanism of Ni/HfOx/TiN RRAM device cells in low resistance state is an ohmic conduction mechanism, while in high resistance state it is a Schottky emission mechanism. The interface between TE and the oxide layer (HfOx) is expected to influence the resistive switching phenomenon. The activation energy of the device is investigated based on the Arrhenius plots in HRS. A switching model is proposed according to the theory of oxygen vacancy conductive filament. Furthermore, the self-compliance behavior is found and explained.

Transparent and flexible resistive switching memory devices with a very high ON / OFF ratio using gold nanoparticles embedded in a silk protein matrix

Ti/HfO2-Based RRAM with Superior Thermal Stability Based on Self-Limited TiOx

Experimental investigation of the reliability issue of RRAM based on high resistance state conduction.

Electrothermal Modeling and Simulation of Resistive Random Access Memory (RRAM) with Different Resistive Switching Oxides

HfO2-Based RRAM with in Situ Conductive Channels Induced by Nanoparticles to Improve Stability

Highly flexible resistive switching memory based on amorphous-nanocrystalline hafnium oxide films.

Investigation of Frenkel-Pair Formation in HfO2 and Its Influence on OxRAM Memory Reliability

HfOx Bipolar Resistive Memory with Robust Endurance Using ZrNx As Buttom Electrode

Tuning oxygen vacancies and resistive switching properties in ultra-thin HfO2 RRAM via TiN bottom electrode and interface engineering

Thermally Stable Transparent Resistive Random Access Memory Based on All‐Oxide Heterostructures

Influneces of Different Oxygen Partial Pressures on Switching Properties of Ni/HfOx/TiN Resistive Switching Devices

Understanding the Switching Oxide Defect Formation and Recovery on HfOx Based RRAM Device

Multilevel Resistive Switching Dynamics by Controlling Phase and Self‐Assembled Nanochannels in HfO2

High Performance Hfox -Based Resistive Ram Devices and Its Temperature Dependent Switching

Interface Engineering With Mos2-Pd Nanoparticles Hybrid Structure For A Low Voltage Resistive Switching Memory

Optimization of the Forming Process of HfOx-Based RRAM to Achieve Bidirectional Forming and Enhanced Switching Performance by Inserting an Oxygen-Vacancy-Rich Layer

Uniform,fast,and Reliable CMOS Compatible Resistive Switching Memory

Insight into interface behavior and microscopic switching mechanism for flexible HfO2 RRAM

Enhancement of Resistive Switching Performance in Hafnium Oxide (HfO2) Devices via Sol-Gel Method Stacking Tri-Layer HfO2/Al-ZnO/HfO2 Structures

A Forming-Free Bipolar Resistive Switching in HfOx-Based Memory with a Thin Ti Cap

Operando diagnostic detection of interfacial oxygen ‘breathing’ of resistive random access memory by bulk-sensitive hard X-ray photoelectron spectroscopy