Abstract:Recently, various miniaturized electronic systems and the rapid increase in power density of microelectronic devices have created additional requirements for micro-scale heat dissipation technology. To dissipate heat in a micro-scale region efficiently, several creative cooling methods for high heat flux dissipation have been designed on the order of 1000 W/cm(2). Due to its high surface-to-volume ratio, the microchannel heat sink has become the most popular one among emerging technologies and an effective tool for high heat flux thermal management. Nevertheless, in common electronic microchannel cooling systems, the traditional parallel microchannel causes a dramatic pressure loss along channel length. In this regard, the manifold microchannel heat sink cooling technology becomes promising with its high heat dissipation potential and moderate pressure drop penalty. The shortened effective flow length compared with the traditional microchannel provides a smaller pressure drop and delays the onset of the critical-heat-flux point. However, while a number of numerical and experimental studies have been conducted for the single-phase flow in the manifold microchannel, two-phase flow boiling in this kind of channel is not widely employed because of its issues with flow pattern prediction. This work develops a new solver based on open source software OpenFOAM to perform the transient process of subcooled flow boiling in the manifold microchannel heat sink. Additionally, heat transfer in the silicon substrate is considered to improve the accuracy of simulation. Similar to single-phase flow simulation for the manifold microchannel, a unit cell model extracted from the whole cooling plate is employed for the two-phase boiling flow to avoid huge computational costs. Through several reasonable assumptions, the symmetry boundary condition is applied on four lateral surfaces in the unit cell, while uniform heat flux is adopted on the bottom wall. A uniform inlet velocity boundary estimated from the total volume flow rate condition is coupled with a fixed temperature value of 7 degrees C lower than saturation temperature. After the mesh independence test, the self-programming solver and numerical methods are validated by comparing numerical results with experimental data. It is determined that the boiling curve obtained by the empirical rate phase-change model with parameters r(1)=r(v)=100 agrees well with experimental results. Furthermore, heat transfer and pressure drop performance differences are caused by microchannel width w(c) and fin width w(f). In comparison to sample A (w(c)=w(f)=15 mu m), decreasing wc and wf simultaneously leads to lower average wall temperature of the heated surface; the channel pressure drop between inlet and outlet surfaces rises dramatically when the widths decrease. When the total number of microchannels in the manifold microchannel cooling plate remains unchanged, increasing wc results in a decreased wf. Based on experimental results, heat sink sample C shows that the pressure loss can be considerably reduced under the premise of sacrificing a small degree of heat transfer performance, which can be attributed to the increased microchannel hydraulic diameter. The manifold microchannel heat sink with w(c)>w(f) is recommended for practical application due to lower pressure loss and average temperature variation.

Transient Numerical Investigation of a Thermal-Driving Water Pipe Cooling System

Two-phase Flow Oscillation and Distribution in Parallel Channels During R1233zd(E) Subcooled Flow Boiling: A Numerical Study

Investigation on flow and heat transfer of fluid in self-driven circulation system for transpiration cooling

Experimental Study on an Thermosyphon Loop with Bubble Pump Effect

Experimental and numerical study of structural parameters on the heat transfer performance of submerged cooling system

Thermal design of a novel heat sink cooled by natural convection with phase transition in the series loop

Numerical investigation on transient and steady phase change heat transfer in the evaporator of a loop heat pipe

Numerical investigation on the characteristics of coolant flow, heat absorption and phase change in transpiration cooling process

Numerical investigation of transient phase-change transpiration cooling based on variable properties of coolant

Numerical Analysis of Flow Boiling Characteristics of a Single Channel Heat Sink Subjected to Multiple Heat Sources

Numerical Simulation of Subcooled Flow Boiling in a Manifold Microchannel Heat Sink

An Experimental Investigation on Instability of Transpiration Cooling with Phase Change

Numerical investigation into the gas-liquid two-phase flow regime and heat transfer characteristics in a gravity heat pipe

Numerical simulation on heat and mass transfer in gravity heat pipe

Experimental and Numerical Study of Transient Electronic Chip Cooling by Liquid Flow in Microchannel Heat Sinks

Numerical Simulation of Transpiration Cooling Within Variable Property of Water and Steam

Numerical Investigation on Flow Pattern, Heat Transfer and Pressure Drop Characteristics of Flow Boiling with Discrete Heat Sources

Transient Analysis of A Cylindrical Heat Pipe Considering Different Wick Structures

NUMERICAL INVESTIGATION ON TRANSPIRATION COOLING BASED ON LOCAL THERMAL NON-EQUILIBRIUM MODEL

Numerical investigation on thermal behavior of high temperature heat pipe based on thermal resistance network model

Numerical simulation on the heat transfer characteristics of two-phase loop thermosyphon with high filling ratios