Abstract:The aim of this work was to study the buckling behavior and failure mode of the double-sided laser-welded Al–Li alloy panel structure under the effect of axial compression via experimental and numerical simulation methods. In the test, multi-frequency fringe projection profilometry was used to monitor the out-of-plane displacement of the laser-welded panel structure during the axial compression load. In addition, the in-plane deformation was precisely monitored via strain gauge and strain rosette. The basic principles of fringe projection profilometry were introduced, and how to use fringe projection profilometry to obtain out-of-plane displacement was also presented. Numerical simulations were performed using the finite element method (FEM) to predict the failure load and buckling modes of the laser-welded panel structure under axial compression, and the obtained results were compared with those of the experiment. It was found that the fringe projection profilometry method for monitoring the buckling deformation of the laser-welded structure was verified to be effective in terms of a measurement accuracy of sub-millimeter level. The structural failure was caused by local buckling of the skin. The observed failure modes such as local buckling of the skin, bending deformation of the stringers, continuous fracture of several welds, and failure of local strength and stiffness were attributed to the deformed laser-welded panel structure under the axial compression. The predicted failure load in the numerical simulation was slightly smaller than that of the experimental test, and the error of the simulation result relative to the test result was −2.7%. The difference between them might be due to the fact that the boundary and loading conditions used in the FEM model could not be completely consistent with those used in the actual experiment.

Experimental and Numerical Investigation on Ultimate Strength of Laser-Welded Stiffened Plates Considering Welding Deformation and Residual Stresses

Numerical and experimental study of residual stress in multi-pass laser welded 5A06 alloy ultra-thick plate

Numerical and experimental study on thermal-metallurgical-mechanical behavior of high-strength steel welded joint

Experimental and Numerical Study on Local Mechanical Properties and Failure Analysis of Laser Welded Dp980 Steels

Investigating Welding Distortion of Thin-Plate Stiffened Panel Steel Structures by Means of Thermal Elastic Plastic Finite Element Method

Finite-element inverse analysis of residual stress for laser welding based on a contour method

Numerical Simulation and Experimental Characterization of Friction Stir Welding on Thick Aluminum Alloy Aa2139-T8 Plates

Stress evolution mechanism during laser welding of ultra-high-strength steel: considering the effects of temperature sensitivity, strain hardening and annealing

Thermal-Elastic-Plastic Finite Element Analysis for Laser Welding Deformation of Thin Plate

Numerical Simulation of Residual Stresses in Multipass Gas Metal Arc-Welded Joints of Thick Aluminum Alloy Plates

Numerical simulation of residual stress and deformation on laser welding of "grooved-coat" structure

Numerical Strength Analysis of Laser-Welded Differential Housing and Gear Considering Residual Stress

Experiment and Numerical Simulation for the Compressive Buckling Behavior of Double-Sided Laser-Welded Al–Li Alloy Aircraft Fuselage Panel

Numerical Investigations on Residual Stress in Laser Penetration Welding Process of Ultrafine-Grained Steel

Experiments and Numerical Simulations on Laser Welding Deformation of Thin Plate Considering Constraint Clamp

First-principles and experimental investigations on ductility/brittleness of intermetallic compounds and joint properties in steel/aluminum laser welding

3D-FEM numerical simulation of welding stress in thin aluminum alloy plate

Influence of Initial Structural Dimensions of Plates on Welding Distortion

Finite Element Analysis of Residual Welding Stresses and Deformation for a 5A06 Aluminum Alloy Plate

Stress and distortion of the 10 mm thick plate EH40 and 316L different butt joints in 10 kW laser welding

Tensile failure analysis of laser stake-welded T-joints: X-ray tomography based conformal finite element and fractal theoretical approaches