Abstract:The 2195 Al-Cu-Li alloy is widely utilized in the aerospace industry due to its lightweight nature and high strength. Consequently, gaining a comprehensive understanding of techniques to enhance its microstructural and mechanical properties is crucial for the consistent production of reliable and high-strength aerospace components. In this investigation, a pristine 2195 industrial ingot was subject to three distinct forging pretreatments: PT1, which involved a direct three upsetting and three stretching (3U3S) process; PT2, which combined double stage homogenization (DH) with 3U3S; and PT3, which involved DH along with six upsetting and six stretching (6U6S). Subsequent warm deformation and T8 aging treatment were applied to the pretreated forgings. The microstructure evolution during the processes and the final mechanical properties in three orthogonal dimensions were examined. The findings revealed that the combination of DH and multi-dimensional forging (MDF) facilitated the dissolution of non-equilibrium phases to a greater extent. Consequently, the main strengthening phase transformed from the T 1 + δ` phase observed in PT1 to the denser T1 + little θ` phase observed in PT2 and PT3 after T8 aging treatment. Notably, the tensile strength and yield strength of PT2 and PT3 specimens increased by 20-30 MPa in all three directions. Moreover, the MDF process accelerated the recrystallization behavior from PT1 to PT3, resulting in a gradual reduction in the average grain size of the pretreated samples from 356 μm to 186 μm. Following warm forging and T8 aging, the grains exhibited a finer and equiaxed structure. Additionally, the coarse phase was identified as the primary source of transgranular cracking. The coarse phases within the matrix became more homogeneous and finer from PT1 to PT3, with a gradual decrease in their area fraction. On the fracture surfaces, the aggregation of coarse phases diminished. Consequently, the elongation in the z-direction improved, and the elongation anisotropy and standard deviation decreased in all three directions for PT3 specimens. The findings presented in this study provide valuable insights into the high-performance manufacturing of Al-Cu-Li alloys.

Effects of High-Intensity Ultrasound on the Microstructure and Mechanical Properties of 2195 Aluminum Ingots

Effect of power ultrasonic treatment on solidification structure of pure aluminum melt

3D characterization of ultrasonic melt processing on the microstructural refinement of Al-Cu alloys by synchrotron X-ray tomography

Optimizing the Microstructure and Mechanical Properties of Vacuum Counter-Pressure Casting ZL114A Aluminum Alloy via Ultrasonic Treatment

Effect of ultrasonic melt processing and Al-Ti-B on the microstructural refinement of recycled Al alloys

Effect of ultrasonic melt processing and cooling rate on microstructure evolution of Al–Cu–Mn–Mg–Fe–Si alloy

Effects of Ultrasonic Stirring on Microstructures of Al 7wt%Si Alloy Ingot

Effects of ultrasonic vibration on the microstructure and mechanical properties of high alloying TiAl

Effect of ultrasonic shot peening on microstructure and mechanical properties of GH3230 superalloy during selective laser melt solution heat treatment

Effects of ultrasonic shot peening process on the microstructure and mechanical properties of nickel-based superalloys formed by selective laser melting

Ultrasonic melt processing upon direct-chill casting of aluminium alloys

Effect of Ultrasonic Vibration on Grain Size and Precipitated Phase Distribution of 6061 Aluminum Alloy Welded Joint

Grain refinement and mechanical properties improvement of Inconel 625 alloy fabricated by ultrasonic-assisted wire and arc additive manufacturing

Influence of Heat Treatment on Nanomechanical Properties of Ni-based Superalloy 625 Fabricated by Ultrasound-Assisted Wire Arc Additive Manufacturing

Microstructure Evolution and Surface Performance of the Rolled 5B70 Aluminum Alloy Processed via Ultrasonic Impact Treatment

Investigation on Microstructure and Mechanical Properties Anisotropy of Inconel625 Components Fabricated by Different Frequency Ultrasonic Vibration-Assisted CMT arc Additive Manufacturing

EFFECT OF HIGH-INTENSITY ULTRASONIC TREATMENT ON REFINEMENT OF Al-5Cu ALLOY INGOTS

The influence of different ultrasonic impact treatment modes on microstructure and mechanical properties of 18Ni-300 steel fabricated by wire arc additive manufacturing

Effect of forging pretreatment on the microstructures and mechanical properties of the Al-Cu-Li alloy

Grain refinement of stainless steel in ultrasound-assisted additive manufacturing

Mechanical property enhancement in gradient structured aluminum alloy by ultrasonic nanocrystalline surface modification