Abstract:Heat treatment is an effective method to improve the mechanical properties of Wire Arc Additive Manufacturing (WAAM) WE43 alloy. This study investigates the effects of heat treatment on the microstructure and mechanical properties of the WE43 alloy processed by WAAM. The as-deposited samples exhibit a uniform equiaxed crystal structure, with grain size gradually increasing as the number of deposited layers grows. The as-deposited microstructure comprises eutectics and a small amount of cubic phases, and the phase content escalates as the amount of deposited layers increases, influenced by the cumulative effect of multiple thermal cycles. At lower solid solution temperatures (480 °C × 8 h), most of the eutectic phase remains undissolved. During tensile testing, undissolved eutectics tend to cause stress concentrations, leading to cracks that result in sample fractures, negatively affecting the mechanical properties. At higher solid solution temperatures (520 °C × 8 h), most of the eutectic dissolves, but abnormal grain coarsening (AGC) in the interlayer fine-grain region occurs, causing a significant reduction in the sample's mechanical properties. After solid solution treatment at 500 °C for 8 h, only a small amount of eutectics remains undissolved, and the AGC phenomenon is not observed, resulting in an optimal solid solution effect. Subsequently, after aging treatment at 225 °C for 18 h, dense nanoscale β′′ phases precipitated within the alloy grains, significantly improving the mechanical properties. The samples achieved optimal performance, with UTS, YS, and EL of 323 ± 15.2 MPa, 225 ± 11.3 MPa, and 8.4 ± 1.1 %, respectively.

Influence of Heat Treatment on Nanomechanical Properties of Ni-based Superalloy 625 Fabricated by Ultrasound-Assisted Wire Arc Additive Manufacturing

Mechanical Properties and Fracture Behavior of Laser Powder-Bed-Fused GH3536 Superalloy

Investigation of a Hot-Pressed Nb–Ti–Al Alloy: Mechanical Alloying, Microstructure and Mechanical Property

Effects of different heat treatment temperatures on the microstructure and mechanical properties of additive manufacturing Ti65 alloys

Effect of heat treatment on microstructure and mechanical properties of WE43 alloy fabricated by wire arc additive manufacturing

Influence of heat treatment on the microstructure and mechanical properties of Al–Mg–Si alloy fabricated by double wires + arc additive manufacturing

Heat Treatment Optimization of 2219 Aluminum Alloy Fabricated by Wire-Arc Additive Manufacturing

Effect of Heat Treatment on Microstructure and Mechanical Properties of a Selective Laser Melting Processed Ni-Based Superalloy GTD222

The influence of different ultrasonic impact treatment modes on microstructure and mechanical properties of 18Ni-300 steel fabricated by wire arc additive manufacturing

Effect of Heat Treatment on the Microstructure of Multiphase Nial-Based Alloy

Effect of heat treatment on the microstructure and properties of CuCrZr alloy manufactured by wire arc additive manufacturing

Comprehensive and Comparative Heat Treatment of Additively Manufactured Inconel 625 Alloy and Corresponding Microstructures and Mechanical Properties

Grain refinement and mechanical properties improvement of Inconel 625 alloy fabricated by ultrasonic-assisted wire and arc additive manufacturing

Effect of Post Processing Heat Treatment Routes on Microstructure and Mechanical Property Evolution of Haynes 282 Ni-Based Superalloy Fabricated with Selective Laser Melting (SLM)

Effect of Nano-Sized γ′ Phase on the Ultrasonic and Mechanical Properties of Ni-Based Superalloy

Effect of heat treatment on the microstructural evolution of a nickel-based superalloy additive-manufactured by laser powder bed fusion

Recrystallization behavior and mechanical properties of Haynes 282 fabricated by wire-arc additive manufacturing with post-heat treatment

Influence of Heat Treatments on Microstructure and Mechanical Properties of Ti⁻26Nb Alloy Elaborated In Situ by Laser Additive Manufacturing with Ti and Nb Mixed Powder

Effect of Heat Treatment Temperature on Microstructure, Tensile Properties and δ-Precipitate Phase in Ni-based Superalloy

Wire arc additive manufacturing of the Al-5.55Cu alloy: Insight the effect of intrinsic heat treatment on microstructure and mechanical properties

Effect of Different Heat Treatments on the Microstructural Evolution and Mechanical Properties of Ni-Cr-Si Alloy Fabricated by Laser Additive Manufacturing